Home › Steering › VARIABLE GEAR RATIO STEERING › VARIABLE GEAR RATIO STEERING SYSTEM › from 2015.08
RM2660E _55 Steering _052825 VARIABLE GEAR RATIO STEERING _0255448 VARIABLE GEAR RATIO STEERING SYSTEM C

VARIABLE GEAR RATIO STEERING  VARIABLE GEAR RATIO STEERING SYSTEM  C15A1/61  Actuator Malfunction  C15A2/62  Open in Motor Circuit  C15A6/62  Actuator Motor Power Distribution Malfunction  


DESCRIPTION

If the VGRS ECU (steering control ECU) detects excessive current, it stores DTC C15A1/61, turns on the master warning light.

If the VGRS ECU (steering control ECU) detects excessive current flowing into the steering actuator assembly or an internal malfunction, it turns the master warning light on, and stores DTC C15A2/62.

If the VGRS ECU (steering control ECU) detects a malfunction in the motor drive circuit, it turns the master warning light on, and stores DTC C15A6/62.

DTC No. DTC Detection Condition Trouble Area
C15A1/61 Either condition is met:
·

After the engine switch is turned on (IG), a short in the motor circuit or an internal ECU (motor drive circuit) malfunction continues for 1.2 seconds or more before control starts.

·

After the engine switch is turned on (IG), a short in the motor circuit or an internal ECU (motor drive circuit) malfunction continues for 0.03 seconds or more.


·

Steering actuator assembly

·

VGRS ECU (steering control ECU)

·

Harness or connector


C15A2/62 Either condition is met:
·

After the engine switch is turned on (IG), an open in the motor circuit or an internal ECU (motor drive circuit) malfunction continues for 1.2 seconds or more before control starts.

·

After the engine switch is turned on (IG), an open in the motor circuit or an internal ECU (motor drive circuit) malfunction continues for 0.03 seconds or more.


·

Steering actuator assembly

·

VGRS ECU (steering control ECU)

·

Harness or connector


C15A6/62 Either condition is met:
·

After the engine switch is turned on (IG), an open in the motor circuit or an internal ECU (motor drive circuit) malfunction continues for 1.2 seconds or more before control starts.

·

After the engine switch is turned on (IG), an open in the motor circuit or an internal ECU (motor drive circuit) malfunction continues for 0.03 seconds or more.


·

Steering actuator assembly

·

VGRS ECU (steering control ECU)

·

Harness or connector



WIRING DIAGRAM

C287217E10
0.927,0.594 1.542,0.792 0.615,0.198 10 false BMU+ 0.927,1.031 1.542,1.229 0.615,0.198 10 false BMV+ 0.906,1.51 1.521,1.708 0.615,0.198 10 false BMW+ 1.448,0.469 1.938,0.656 0.49,0.188 10 false 4 1.448,0.927 1.938,1.115 0.49,0.188 10 false 5 1.396,1.375 1.885,1.563 0.49,0.188 10 false 13 0.229,1.885 0.844,2.083 0.615,0.198 10 false E80 3.438,2.833 4.052,3.031 0.615,0.198 10 false VGRS 5.844,0.583 6.458,0.781 0.615,0.198 10 false BMU 5.844,1.042 6.458,1.24 0.615,0.198 10 false BMV 5.844,1.5 6.458,1.698 0.615,0.198 10 false BMW 5.844,1.958 6.458,2.156 0.615,0.198 10 false SG 5.844,2.698 6.458,2.896 0.615,0.198 10 false PIG 5.844,3.167 6.458,3.365 0.615,0.198 10 false PGND 5.427,0.583 6.042,0.781 0.615,0.198 10 false E160 5.438,2.688 6.052,2.885 0.615,0.198 10 false E159 5.438,3.156 6.052,3.354 0.615,0.198 10 false E159 5.552,0.385 5.844,0.563 0.292,0.177 10 false 3 5.552,0.844 5.844,1.021 0.292,0.177 10 false 2 5.552,1.302 5.844,1.479 0.292,0.177 10 false 1 5.552,1.771 5.844,1.948 0.292,0.177 10 false 5 5.552,2.49 5.844,2.667 0.292,0.177 10 false 2 5.552,2.969 5.844,3.146 0.292,0.177 10 false 1 5.385,3.865 7.063,4.313 1.677,0.448 10 false VGRS ECU (Front Steering Control ECU) 0.229,2.042 2.052,2.25 1.823,0.208 10 false Steering Actuator Assembly 1.417,2.688 2.208,2.906 0.792,0.219 10 false from Battery 5.427,1.042 6.042,1.24 0.615,0.198 10 false E160 5.438,1.49 6.052,1.688 0.615,0.198 10 false E160 5.417,1.958 6.031,2.156 0.615,0.198 10 false E160

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the VGRS ECU (steering control ECU) or steering actuator assembly, perform actuator angle neutral point calibration and initialization after replacing parts (See page Steering>VARIABLE GEAR RATIO STEERING>VARIABLE GEAR RATIO STEERING SYSTEM>CALIBRATION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



HINT:

When DTC C15A2/62 is output, a short circuit inside the steering actuator assembly or inside the VGRS ECU (steering control ECU) is suspected.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (PIG, PGND TERMINAL)
a.
U165228E02
1.448,1.156 1.073,1.521 1.073,1.521 1.073,1.646 false 1.646,1.156 1.938,1.521 1.938,1.521 1.938,1.646 false 0.073,0.063 0.281,0.25 0.208,0.188 10 false *a 0.771,1.698 1.271,1.885 0.5,0.188 10 false 2 (PIG) 1.542,0.26 1.906,0.417 0.365,0.156 10 false E159 1.635,1.688 2.302,1.875 0.667,0.188 10 false 1 (PGND)

Turn the engine switch off.


b.

Measure the resistance according to the value(s) in the table below.

HINT:

Perform the inspection from the rear of the connector with the connector connected to the VGRS ECU (steering control ECU).


Standard Resistance:
Tester Connection Condition Specified Condition
E159-1(PGND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
E159-2(PIG) - E159-1(PGND) Always 11 to 14 V



Text in Illustration
*a Component with harness connected
(VGRS ECU [Steering Control ECU])


OK

2.INSPECT STEERING ACTUATOR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT STEERING ACTUATOR ASSEMBLY
a.
C358496E01
1.479,0.323 1.896,0.563 0.417,0.24 1.01,1.74 1.01,1.583 1.01,1.583 1.271,1.25 false 1.615,1.76 1.615,1.25 false 2.177,1.76 2.177,1.615 2.177,1.615 1.958,1.24 false 1.521,0.365 2.135,0.563 0.615,0.198 10 false E160 0.177,0.156 0.792,0.354 0.615,0.198 10 false *a 0.844,1.781 1.458,1.979 0.615,0.198 10 false BMW 1.5,1.781 2.115,1.979 0.615,0.198 10 false BMV 2.052,1.781 2.667,1.979 0.615,0.198 10 false BMU

Disconnect the E160 VGRS ECU (steering control ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

HINT:

Measure the resistance of the steering actuator assembly at the connector of the VGRS ECU (steering control ECU).


Standard Resistance:
Tester Connection Condition Specified Condition
E160-2 (BMV) - E160-3 (BMU) Always Below 1 Ω
E160-2 (BMV) - E160-1 (BMW) Always Below 1 Ω
E160-3 (BMU) - E160-1 (BMW) Always Below 1 Ω
E160-1 (BMW) - Body ground Always 100 kΩ or higher
E160-2 (BMV) - Body ground Always 100 kΩ or higher
E160-3 (BMU) - Body ground Always 100 kΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to VGRS ECU [Steering Control ECU])

Result
Result Proceed to
The resistance value deviates from the standard A
The resistance value is within the standard B



A

3.CHECK HARNESS AND CONNECTOR (VGRS ECU (STEERING CONTROL ECU) - STEERING ACTUATOR ASSEMBLY)

B

4.RECONFIRM DTC
3.CHECK HARNESS AND CONNECTOR (VGRS ECU (STEERING CONTROL ECU) - STEERING ACTUATOR ASSEMBLY)
a.

Turn the engine switch off.


b.

Disconnect the E160 VGRS ECU (steering control ECU) connector.


c.

Disconnect the E80 steering actuator assembly connector.


d.

Measure the resistance according to the value(s) in the table below.


Standard Resistance:
Tester Connection Condition Specified Condition
E160-2 (BMV) - E80-5 (BMV+) Always Below 1 Ω
E160-3 (BMU) - E80-4 (BMU+) Always Below 1 Ω
E160-1 (BMW) - E80-13 (BMW+) Always Below 1 Ω
E160-2 (BMV) - E160-3 (BMU) Always 100 kΩ or higher
E160-2 (BMV) - E160-1 (BMW) Always 100 kΩ or higher
E160-3 (BMU) - E160-1 (BMW) Always 100 kΩ or higher
E160-2 (BMV) or E80-5 (BMV+) - Body ground Always 100 kΩ or higher
E160-3 (BMU) or E80-4 (BMU+) - Body ground Always 100 kΩ or higher
E160-1 (BMW) or E80-13 (BMW+) - Body ground Always 100 kΩ or higher



OK

REPLACE STEERING ACTUATOR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.RECONFIRM DTC
a.

Reconnect the E160 VGRS ECU (steering control ECU) connector.



c.

Turn the engine switch off.


d.

Start the engine.


e.

Check for DTCs (See page Steering>VARIABLE GEAR RATIO STEERING>VARIABLE GEAR RATIO STEERING SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTCs C15A1/61, C15A2/62 and C15A6/62 is not output (for LHD) A
DTCs C15A1/61, C15A2/62 and C15A6/62 is not output (for RHD) B
DTCs C15A1/61, C15A2/62 and C15A6/62 is output C



A

REPLACE VGRS ECU (STEERING CONTROL ECU)

B

REPLACE VGRS ECU (STEERING CONTROL ECU)

C

REPLACE STEERING ACTUATOR ASSEMBLY