The steering control ECU drives the actuator based on steering angle sensor signals and vehicle speed signals.
If the steering control ECU detects excessive current flowing into the steering actuator, or an internal malfunction, it will turn on the master warning light, store DTC C15A2/62, and stop VGRS operation.
If the steering control ECU detects a malfunction in the motor drive circuit, it will turn the master warning light on, store DTC C15A6/62, and stop VGRS operation.
| DTC Code | DTC Detection Condition | Trouble Area |
|---|---|---|
| C15A2/62 | The VGRS system detects a malfunction in the motor drive circuit. | ·
Harness or connector ·
Power source circuit ·
Steering actuator ·
Steering control ECU |
| C15A6/62 | The actual motor current value greatly differs from the estimated value. | ·
Power source circuit ·
Harness or connector ·
Steering actuator ·
Steering control ECU |
Only the actuator only can be checked in this procedure. If it is normal, the steering control ECU is faulty.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E77-7 (PGND) - Body ground | Always | Below 1 Ω |
| E78-8 (PGD2) - Body ground |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E77-8 (PIG) - Body ground | Always | 11 to 14 V |
OK
NG
Disconnect the E78 steering control ECU connector.
Disconnect the E80 steering actuator connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E78-1 (BMV) - E78-2 (BMU) | Always | 10 kΩ or higher |
| E78-1 (BMV) - E78-3 (BMW) | ||
| E78-2 (BMU) - E78-3 (BMW) | ||
| E78-1 (BMV) - E80-5 (BMV+) | Always | Below 1 Ω |
| E78-2 (BMU) - E80-4 (BMU+) | ||
| E78-3 (BMW) - E80-13 (BMW+) | ||
| E78-1 (BMV) - Body ground | Always | 10 kΩ or higher |
| E78-2 (BMU) - Body ground | ||
| E78-3 (BMW) - Body ground |
OK
NG
Disconnect the E78 steering control ECU connector.
Measure the resistance according to the value(s) in the table below.
The resistance must be measured with the steering actuator connector connected.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E78-1 (BMV) - E78-2 (BMU) | Always | Below 1 Ω |
| E78-1 (BMV) - E78-3 (BMW) | ||
| E78-2 (BMU) - E78-3 (BMW) | ||
| E78-1 (BMV) - Body ground | Always | 10 kΩ or higher |
| E78-2 (BMU) - Body ground | ||
| E78-3 (BMW) - Body ground |
OK
NG
Check for DTCs (See page Steering>VARIABLE GEAR RATIO STEERING>VARIABLE GEAR RATIO STEERING SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| C15A1/61 is output | A |
| C15A1/61 is not output (for LHD) | B |
| C15A1/61 is not output (for RHD) | C |
A
B
C