Home › Steering › VARIABLE GEAR RATIO STEERING › VARIABLE GEAR RATIO STEERING SYSTEM › from 2015.08
RM2660E _55 Steering _052825 VARIABLE GEAR RATIO STEERING _0255448 VARIABLE GEAR RATIO STEERING SYSTEM C

VARIABLE GEAR RATIO STEERING  VARIABLE GEAR RATIO STEERING SYSTEM  C15A3/63  Motor Rotation Angle Not Detected  C15C5/69  Motor Rotation Signal Not Detected  


DESCRIPTION

The steering actuator assembly drives the internal motor using the current output from the VGRS ECU (steering control ECU) to change the relative angle between the tire angle and steering wheel angle.

The motor rotation angle sensor in the steering actuator assembly detects the motor rotation angle and outputs this information to the VGRS ECU (steering control ECU).

If the VGRS ECU (steering control ECU) detects a malfunction in the motor rotation angle sensor circuit, it stores DTC C15A3/63.

The test mode DTC C15C5/69 is only stored during test mode.

DTC No. DTC Detection Condition Trouble Area
C15A3/63 All conditions are met for approximately 0.03 seconds or more:
·

2 seconds or more elapse after turning the engine switch on (IG).

·

2 seconds or more elapse with the power source voltage at 10 V or higher.

·

A problem with the motor rotation angle sensor is detected.


·

Steering actuator assembly

·

VGRS ECU (steering control ECU)

·

Harness or connector


C15C5/69 The system enters test mode.
·

Steering actuator assembly

·

VGRS ECU (steering control ECU)

·

Harness or connector



WIRING DIAGRAM

C256577E13
0.281,3.01 2.479,3.208 2.198,0.198 10 false Steering Actuator Assembly 5.25,3.083 6.958,3.479 1.708,0.396 10 false VGRS ECU (Front Steering Control ECU) 5.25,2.885 5.917,3.135 0.667,0.25 10 false E162 5.792,0.313 6.104,0.5 0.313,0.188 10 false RV 5.792,0.677 6.104,0.865 0.313,0.188 10 false S1 5.792,1.063 6.104,1.25 0.313,0.188 10 false S2 5.792,1.458 6.104,1.646 0.313,0.188 10 false RG 5.792,1.823 6.104,2.01 0.313,0.188 10 false LV 5.792,2.188 6.104,2.375 0.313,0.188 10 false LG 5.792,2.552 6.198,2.74 0.406,0.188 10 false SG2+ 1.177,0.313 1.49,0.5 0.313,0.188 10 false RV+ 1.188,0.698 1.5,0.885 0.313,0.188 10 false S1+ 1.188,1.063 1.5,1.25 0.313,0.188 10 false S2+ 1.177,1.438 1.49,1.625 0.313,0.188 10 false RG+ 1.188,1.833 1.5,2.021 0.313,0.188 10 false LV+ 1.188,2.198 1.5,2.385 0.313,0.188 10 false LG+ 5.594,0.552 5.771,0.729 0.177,0.177 10 false 3 5.594,0.177 5.771,0.354 0.177,0.177 10 false 9 1.531,2.083 1.74,2.26 0.208,0.177 10 false 16 1.542,0.583 1.698,0.771 0.156,0.188 10 false 2 1.542,0.219 1.698,0.406 0.156,0.188 10 false 1 5.594,1.688 5.75,1.875 0.156,0.188 10 false 2 1.542,0.99 1.698,1.177 0.156,0.188 10 false 9 1.552,1.708 1.708,1.896 0.156,0.188 10 false 7 1.521,1.344 1.729,1.521 0.208,0.177 10 false 10 5.594,0.927 5.802,1.104 0.208,0.177 10 false 5 5.594,1.313 5.802,1.49 0.208,0.177 10 false 8 5.594,2.073 5.802,2.25 0.208,0.177 10 false 6 5.552,2.448 5.76,2.625 0.208,0.177 10 false 10 0.292,2.823 0.604,2.99 0.313,0.167 10 false E80 3.365,2.698 3.948,2.896 0.583,0.198 10 false Shielded

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the VGRS ECU (steering control ECU) or steering actuator assembly, perform actuator angle neutral point calibration and initialization after replacing parts (See page Steering>VARIABLE GEAR RATIO STEERING>VARIABLE GEAR RATIO STEERING SYSTEM>CALIBRATION).

·

Since DTC C1289 is stored in the skid control ECU (master cylinder solenoid), after performing repairs on the VGRS system, clear the DTCs for the vehicle stability control system.



PROCEDURE

1.CHECK DTC
a.

Check for DTCs (See page Steering>VARIABLE GEAR RATIO STEERING>VARIABLE GEAR RATIO STEERING SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
·

DTC C15A3/63 is output as a current DTC

·

When the engine is started and the steering wheel is operated, DTC C15A3/63 is output as a current DTC.


A
When the engine is started and a wire harness is jiggled, DTC C15A3/63 is output as a current DTC. B
DTC C15A3/63 is not output as a current DTC C



A

2.CHECK FRAME DATA (MOTOR RESOLVER SIN PHASE OFFSET,MOTOR RESOLVER COS PHASE OFFSET)

B

REPAIR OR REPLACE HARNESS OR CONNECTOR

C

2.CHECK FRAME DATA (MOTOR RESOLVER SIN PHASE OFFSET,MOTOR RESOLVER COS PHASE OFFSET)
a.

Turn the engine switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the engine switch on (IG).


d.

Turn the GTS on.



f.

Select DTC "C15A3/63", and check the freeze frame data for "Motor Resolver SIN Phase Offset" and "Motor Resolver COS Phase Offset" (See page Steering>VARIABLE GEAR RATIO STEERING>VARIABLE GEAR RATIO STEERING SYSTEM>FREEZE FRAME DATA).

Result
Result Proceed to
"Motor Resolver SIN Phase Offset" and "Motor Resolver COS Phase Offset" are 5 V or higher A
"Motor Resolver SIN Phase Offset" and "Motor Resolver COS Phase Offset" are below 5 V (for LHD) B
"Motor Resolver SIN Phase Offset" and "Motor Resolver COS Phase Offset" are below 5 V (for RHD) C



A

3.INSPECT STEERING ACTUATOR ASSEMBLY

B

REPLACE VGRS ECU (STEERING CONTROL ECU)

C

REPLACE VGRS ECU (STEERING CONTROL ECU)

3.INSPECT STEERING ACTUATOR ASSEMBLY
a.

Turn the engine switch off.


b.
U165257E02
1.698,1.135 1.042,1.604 1.042,1.604 1.042,1.729 false 1.99,1.135 2.365,1.604 2.365,1.604 2.365,1.729 false 1.719,1.302 1.448,1.604 1.448,1.604 1.448,1.729 false 1.854,1.292 1.854,1.729 false 0.115,0.094 0.292,0.26 0.177,0.167 10 false *a 0.938,1.76 1.156,1.927 0.219,0.167 10 false S1 1.302,1.76 1.563,1.927 0.26,0.167 10 false RG 1.74,1.76 1.958,1.927 0.219,0.167 10 false RV 2.271,1.76 2.49,1.927 0.219,0.167 10 false S2 1.552,0.323 1.917,0.479 0.365,0.156 10 false E162

Disconnect the E162 VGRS ECU (steering control ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

HINT:

Measure the resistance of the steering actuator assembly at the connector of the VGRS ECU (steering control ECU).


Standard Resistance:
Tester Connection Condition Specified Condition
E162-9 (RV) - E162-8 (RG) Always 20 to 60 Ω
E162-3 (S1) - E162-8 (RG) Always 70 to 160 Ω
E162-5 (S2) - E162-8 (RG) Always 60 to 150 Ω
E162-9 (RV) - E162-3 (S1) Always 90 to 220 Ω
E162-9 (RV) - E162-5 (S2) Always 80 to 210 Ω
E162-3 (S1) - E162-5 (S2) Always 130 to 310 Ω
E162-3 (S1) - Body ground Always 100 kΩ or higher
E162-5 (S2) - Body ground Always 100 kΩ or higher
E162-8 (RG) - Body ground Always 100 kΩ or higher
E162-9 (RV) - Body ground Always 100 kΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to VGRS ECU [Steering Control ECU])

Result
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C



A

REPLACE VGRS ECU (STEERING CONTROL ECU)

B

REPLACE VGRS ECU (STEERING CONTROL ECU)

C

4.CHECK HARNESS AND CONNECTOR (VGRS ECU (STEERING CONTROL ECU) - STEERING ACTUATOR ASSEMBLY)
4.CHECK HARNESS AND CONNECTOR (VGRS ECU (STEERING CONTROL ECU) - STEERING ACTUATOR ASSEMBLY)
a.

Turn the engine switch off.


b.

Disconnect the E162 VGRS ECU (steering control ECU) connector.


c.

Disconnect the E80 steering actuator assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E162-3 (S1) - E80-2 (S1+) Always Below 1 Ω
E162-5 (S2) - E80-9 (S2+) Always Below 1 Ω
E162-8 (RG) - E80-10 (RG+) Always Below 1 Ω
E162-9 (RV) - E80-1 (RV+) Always Below 1 Ω
E162-9 (RV) - E162-8 (RG) Always 20 to 60 Ω
E162-3 (S1) - E162-8 (RG) Always 70 to 160 Ω
E162-5 (S2) - E162-8 (RG) Always 60 to 150 Ω
E162-9 (RV) - E162-3 (S1) Always 90 to 220 Ω
E162-9 (RV) - E162-5 (S2) Always 80 to 210 Ω
E162-3 (S1) - E162-5 (S2) Always 130 to 310 Ω
E162-3 (S1) or E80-2 (S1+) - Body ground Always 100 kΩ or higher
E162-5 (S2) or E80-9 (S2+) - Body ground Always 100 kΩ or higher
E162-8 (RG) or E80-10 (RG+) - Body ground Always 100 kΩ or higher
E162-9 (RV) or E80-1 (RV+) - Body ground Always 100 kΩ or higher




OK

REPLACE STEERING ACTUATOR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR