Home › Steering › STEERING COLUMN › STEERING COLUMN ASSEMBLY (for Manual Tilt and Manual Telescopic Steering Column) › 2014.08–2015.08
RM2660E _55 Steering _052826 STEERING COLUMN _0255458 STEERING COLUMN ASSEMBLY(for Manual Tilt and Manual Telescopic Steering Column) A

STEERING COLUMN  STEERING COLUMN ASSEMBLY(for Manual Tilt and Manual Telescopic Steering Column)  REMOVAL  


CAUTION / NOTICE / HINT

CAUTION:

Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing the steering column (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION).


HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 1. FRONT WHEELS FACING STRAIGHT AHEAD

Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:
·

After the engine switch is turned off, the navigation system requires approximately 90 seconds to record various types of memory and settings. As a result, after turning the engine switch off, wait 90 seconds or more before disconnecting the cable from the negative (-) battery terminal.

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



Hide 45187 3.REMOVE LOWER NO. 3 STEERING WHEEL COVER

Hide 45186 4.REMOVE LOWER NO. 2 STEERING WHEEL COVER

Hide 45100 6.REMOVE STEERING WHEEL ASSEMBLY

Hide 7.REMOVE LOWER STEERING COLUMN COVER

a.
C179481

Remove the 3 screws.


b.

Detach the 2 claws to remove the lower steering column cover.


Hide 45286B 8.REMOVE UPPER STEERING COLUMN COVER

a.
C179482

Detach the 4 clips.


b.

Detach the claw to remove the upper steering column cover.


Hide 9.REMOVE COMBINATION SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY

a.

Disconnect the connectors from the combination switch with spiral cable.


b.
U164929

Using pliers, grip the claws of the clamp and remove the combination switch with spiral cable from the steering column.


Hide 55449C 10.REMOVE NO. 2 INSTRUMENT PANEL FINISH PANEL CUSHION

Hide 55403C 11.REMOVE LOWER INSTRUMENT PANEL PAD SUB-ASSEMBLY LH

Hide 55474C 13.REMOVE NO. 1 INSTRUMENT CLUSTER FINISH PANEL GARNISH

Hide 55475A 14.REMOVE NO. 2 INSTRUMENT CLUSTER FINISH PANEL GARNISH

Hide 55404C 15.REMOVE INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY (w/ Multi-information Display)

Hide 55404C 16.REMOVE INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY (w/o Multi-information Display)

Hide 55606 17.REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (w/ Floor Under Cover)

Hide 67914B 18.REMOVE FRONT DOOR SCUFF PLATE LH

Hide 55432D 20.REMOVE LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL

Hide 73900 22.REMOVE DRIVER SIDE KNEE AIRBAG ASSEMBLY (w/ Driver Side Knee Airbag)

Hide 55303B 23.REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY (w/o Driver Side Knee Airbag)

Hide 24.DISCONNECT WIRE HARNESS PROTECTOR AND WIRE HARNESS

a.
C172656

Detach the 2 claws to disconnect the wire harness protector and wire harness.


Hide 45250 26.REMOVE STEERING COLUMN ASSEMBLY

a.
C172648E03
1.906,1.208 2.417,0.99 2.417,0.99 1.917,0.75 true 2.469,0.906 2.729,1.125 0.26,0.219 10 false *a

Put matchmarks on the steering intermediate shaft and the steering column.

Text in Illustration
*a Matchmark


b.

Remove the bolt.


c.

w/o Entry and Start System:

i.
C358201

Remove the 4 nuts and steering column.



d.

w/ Entry and Start System:

i.
C172654

Remove the 4 nuts and steering column.



Hide 27.REMOVE FRONT WHEEL

Hide 45220 28.DISCONNECT STEERING INTERMEDIATE SHAFT ASSEMBLY

a.
C172649E05
1.854,0.885 2.51,0.979 2.51,0.979 1.719,1.021 true 2.563,0.875 2.802,1.052 0.24,0.177 10 false *a

Put matchmarks on the steering intermediate shaft and the No. 2 steering intermediate shaft.

Text in Illustration
*a Matchmark


b.

Remove the bolt, and then pull out the intermediate shaft toward the inside of the vehicle.


Hide 45026D 29.REMOVE STEERING COLUMN HOLE COVER SUB-ASSEMBLY

a.
C358207

Hold the clamp with needle nose pliers, then insert a screwdriver and turn it in the direction shown in the illustration to remove the clamp of the steering column hole cover.


b.
C179099

Remove the 4 bolts and nut with the steering column hole cover from the vehicle.


Hide 45203A 30.DISCONNECT NO. 2 STEERING INTERMEDIATE SHAFT

a.
C358214E01
0.708,1.604 0.885,0.427 0.885,0.427 1.188,0.427 false 0.802,1.573 1.052,0.438 false 1.26,0.333 1.573,0.531 0.313,0.198 10 false *a 2.667,1.135 2.844,1.323 0.177,0.188 10 false A

Loosen the bolt and remove the No. 2 intermediate shaft.

Text in Illustration
*a Matchmark

NOTICE:

It is possible to install the intermediate shaft to the same position it was removed from without placing matchmarks due to the dust cover part labeled A. Therefore, do not remove the dust cover from the steering link.


HINT:

If the dust cover is removed/installed or replaced, place matchmarks on the dust cover and steering link.