Home › Steering › STEERING COLUMN › STEERING COLUMN ASSEMBLY (for Manual Tilt and Manual Telescopic Steering Column) › from 2015.08
RM2660E _55 Steering _052826 STEERING COLUMN _0255458 STEERING COLUMN ASSEMBLY(for Manual Tilt and Manual Telescopic Steering Column) A

STEERING COLUMN  STEERING COLUMN ASSEMBLY(for Manual Tilt and Manual Telescopic Steering Column)  REMOVAL  


CAUTION / NOTICE / HINT

CAUTION:

Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing the steering column (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION).


HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 1. FRONT WHEELS FACING STRAIGHT AHEAD

Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:
·

After the ignition switch is turned off, the navigation system requires approximately 90 seconds to record various types of memory and settings. As a result, after turning the ignition switch off, wait 90 seconds or more before disconnecting the cable from the negative (-) battery terminal.

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



Hide 45100 3.REMOVE STEERING WHEEL ASSEMBLY

Hide 4.REMOVE LOWER STEERING COLUMN COVER

a.
C348616

Remove the 3 screws.


b.
C358209E01
0.344,1.01 0.156,0.719 0.156,0.719 0.156,0.323 true 2.917,0.917 3.083,0.75 3.083,0.75 3.083,0.302 true 0.156,0.333 0.302,0.333 false 2.927,0.302 3.083,0.302 false 0.344,0.25 1.208,0.74 0.865,0.49 10 true Push Area 2.094,0.24 2.948,0.667 0.854,0.427 10 true Push Area

While pressing the push area shown in the illustration to detach the 2 claws, slightly lower steering column cover.


Hide 45286B 5.REMOVE UPPER STEERING COLUMN COVER

a.
C348617E01
0.145,0.694 1.069,1.045 0.924,0.350 10 Meter Hood Spacer 1.653,1.751 1.124,0.809 false

Detach the 4 clips and 2 claws remove the meter hood spacer.


b.

Detach the claw and 2 guide pin remove the upper steering column cover from the steering column assembly.


Hide 6.REMOVE COMBINATION SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY

a.

Disconnect the connectors from the combination switch with spiral cable.


b.
C347263

Using pliers, grip the claws of the clamp and remove the combination switch with spiral cable from the steering column.


Hide 73900 7.REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY (w/ Driver Side Knee Airbag)

Hide 55303B 8.REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY (w/o Driver Side Knee Airbag)

Hide 9.DISCONNECT WIRE HARNESS PROTECTOR AND WIRE HARNESS

a.

Remove the 2 wire harness cramps.


b.
C172656

Detach the 2 claws to disconnect the wire harness protector and wire harness.


Hide 45250 11.REMOVE STEERING COLUMN ASSEMBLY

a.
C172648E03
1.906,1.208 2.417,0.99 2.417,0.99 1.917,0.75 true 2.469,0.906 2.729,1.125 0.26,0.219 10 false *a

Put matchmarks on the steering intermediate shaft and the steering column.

Text in Illustration
*a Matchmark


b.

Remove the bolt.


c.

w/o Entry and Start System:

i.
C347265

Remove the 4 nuts and steering column.



d.

w/ Entry and Start System:

i.
C347266

Remove the 4 nuts and steering column.



Hide 12.REMOVE FRONT WHEEL

Hide 45220 13.DISCONNECT STEERING INTERMEDIATE SHAFT ASSEMBLY

a.
C172649E05
1.854,0.885 2.51,0.979 2.51,0.979 1.719,1.021 true 2.563,0.875 2.802,1.052 0.24,0.177 10 false *a

Put matchmarks on the steering intermediate shaft and the No. 2 steering intermediate shaft.

Text in Illustration
*a Matchmark


b.

Remove the bolt, and then pull out the intermediate shaft toward the inside of the vehicle.


Hide 45026D 14.REMOVE STEERING COLUMN HOLE COVER SUB-ASSEMBLY

a.
C358207

Hold the clamp with needle nose pliers, then insert a screwdriver and turn it in the direction shown in the illustration to remove the clamp of the steering column hole cover.


b.
C179099

Remove the 4 bolts and nut with the steering column hole cover from the vehicle.


Hide 45203A 15.DISCONNECT NO. 2 STEERING INTERMEDIATE SHAFT

a.
C358214E01
0.708,1.604 0.885,0.427 0.885,0.427 1.188,0.427 false 0.802,1.573 1.052,0.438 false 1.26,0.333 1.573,0.531 0.313,0.198 10 false *a 2.667,1.135 2.844,1.323 0.177,0.188 10 false A

Loosen the bolt and remove the No. 2 intermediate shaft.

Text in Illustration
*a Matchmark

NOTICE:

It is possible to install the intermediate shaft to the same position it was removed from without placing matchmarks due to the dust cover part labeled A. Therefore, do not remove the dust cover from the steering link.


HINT:

If the dust cover is removed/installed or replaced, place matchmarks on the dust cover and steering link.