Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for LHD vehicles.
1. TABLE OF BOLT, SCREW AND NUT
All bolts, screws and nuts relevant to installing and removing the instrument panel are shown along with their alphabet code in the table below.
2. RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM (w/ Cool Box)
3.DISABLE AUTOAWAY/RETURN FUNCTION (for Power Tilt and Power Telescopic Steering Column)
Disable the autoaway/return function by changing the customize parameter (See page Steering>STEERING COLUMN>POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM>CUSTOMIZE PARAMETERS).
Record the current customize parameter setting (whether the autoaway/return function is enabled or disabled) in order to restore the current setting after finishing the operation.
Performing the above operation causes the autoaway/return function to be disabled when the engine switch is turned off.
Turn the ignition switch on (IG). Operate the tilt and telescopic switch to fully extend and lower the steering column assembly.
Turn the ignition switch off.
4. PRECAUTION
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
5.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
6.REMOVE FRONT SEAT ASSEMBLY LH
for Manual Seat:
(See page Vehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Manual Seat)>REMOVAL)
for Power Seat:
(See page Vehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Power Seat)>REMOVAL)
7.REMOVE FRONT SEAT ASSEMBLY RH
for Manual Seat:
(See page Vehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Manual Seat)>REMOVAL)
for Power Seat:
(See page Vehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Power Seat)>REMOVAL)
for Bench Seat Type:
(See page Vehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Bench Seat Type)>REMOVAL)
84140
8.REMOVE HEADLIGHT DIMMER SWITCH ASSEMBLY
58901A
9.REMOVE REAR CONSOLE BOX SUB-ASSEMBLY (w/o Cool Box)
88520
10.REMOVE COOLING BOX ASSEMBLY (w/ Cool Box)
58812A
11.REMOVE LOWER CONSOLE BOX (w/o Console Box Lid)
55318C
12.REMOVE INSTRUMENT SIDE PANEL LH
Put protective tape around the instrument side panel LH.
| *a | Protective Tape |
Using a moulding remover A, detach the 6 claws and remove the instrument side panel LH.
55474C
13.REMOVE NO. 1 INSTRUMENT CLUSTER FINISH PANEL GARNISH
Put protective tape around the No. 1 instrument cluster finish panel garnish.
| *a | Protective Tape |
Using a moulding remover A, detach the 3 claws and remove the No. 1 instrument cluster finish panel garnish.
55475A
14.REMOVE NO. 2 INSTRUMENT CLUSTER FINISH PANEL GARNISH
Put protective tape around the No. 2 instrument cluster finish panel garnish.
| *a | Protective Tape |
Using a moulding remover A, detach the 2 claws and remove the No. 2 instrument cluster finish panel garnish.
55404C
15.REMOVE NO. 2 INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY
Put protective tape around the No. 2 instrument cluster finish panel sub-assembly.
| *a | Protective Tape |
Detach the 9 claws.
Disconnect the connectors and remove the No. 2 instrument cluster finish panel sub-assembly.
83100
16.REMOVE COMBINATION METER ASSEMBLY
Remove the 4 screws.
Disconnect the connectors and remove the combination meter assembly.
67914B
17.REMOVE FRONT DOOR SCUFF PLATE LH
55606
18.REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (w/ Floor Under Cover)
Remove the 2 screws <A>.
| *a | Screw <A> |
Detach the 3 claws.
Disconnect the connector and remove the No. 1 instrument panel under cover sub-assembly.
62112
19.REMOVE COWL SIDE TRIM BOARD LH
Remove the cap nut.
| *a | Cap Nut |
Detach the 2 clips and remove the cowl side trim board LH.
55432D
20.REMOVE LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL
Using a screwdriver, detach the 2 claws and open the hole cover.
Tape the screwdriver tip before use.
| *a | Protective Tape |
Put protective tape around the lower No. 1 instrument panel finish panel.
Remove the 2 bolts <B>.
| *a | Protective Tape |
| *b | Bolt <B> |
w/ Driver Side Knee Airbag:
Detach the 16 claws.
w/o Driver Side Knee Airbag:
Detach the 9 claws.
for Automatic Air Conditioning System:
Detach the 2 claws and remove the room temperature sensor.
Detach the 2 claws and disconnect the 2 control cables.
Disconnect the connectors and remove the lower No. 1 instrument panel finish panel.
55446A
21.REMOVE NO. 1 SWITCH HOLE BASE
Put protective tape around the No. 1 switch hole base.
| *a | Protective Tape |
Detach the 4 claws.
Disconnect the connectors and remove the No. 1 switch hole base.
73900
22.REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY (w/ Driver Side Knee Airbag)
55303B
23.REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY (w/o Driver Side Knee Airbag)
Detach the 2 claws and disconnect the DLC3.
Remove the 5 bolts <B> and lower instrument panel sub-assembly.
| *a | Bolt <B> |
55650
24.REMOVE NO. 1 INSTRUMENT PANEL REGISTER ASSEMBLY
Put protective tape around the No. 1 instrument panel register assembly.
| *a | Protective Tape |
Detach the 4 claws and remove the No. 1 instrument panel register assembly.
55317A
25.REMOVE INSTRUMENT SIDE PANEL RH
Put protective tape around the instrument side panel RH.
| *a | Protective Tape |
Using a moulding remover A, detach the 6 claws and remove the instrument side panel RH.
w/ Airbag Cut Off Switch:
Disconnect the connector and remove the instrument side panel RH.
67913B
26.REMOVE FRONT DOOR SCUFF PLATE RH
55607
27.REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (w/ Floor Under Cover)
Detach the 4 claws and 3 guides.
Disconnect the connector and remove the No. 2 instrument panel under cover sub-assembly.
62111C
28.REMOVE COWL SIDE TRIM BOARD RH
Remove the cap nut.
| *a | Cap Nut |
Detach the 2 clips and remove the cowl side trim board LH.
73990
29.REMOVE LOWER NO. 2 INSTRUMENT PANEL AIRBAG ASSEMBLY (w/ Passenger Side Knee Airbag)
55312
30.REMOVE LOWER INSTRUMENT PANEL (w/o Passenger Side Knee Airbag)
Remove the 2 bolts <B>.
| *a | Bolt <B> |
Detach the 4 claws and remove the lower instrument panel.
55476A
31.REMOVE NO. 3 INSTRUMENT CLUSTER FINISH PANEL GARNISH
Put protective tape around the No. 3 instrument cluster finish panel garnish.
| *a | Protective Tape |
Using a moulding remover A, detach the 6 claws and remove the No. 3 instrument cluster finish panel garnish.
55443D
32.REMOVE INSTRUMENT PANEL BOX DOOR KNOB
Use the same procedure for both instrument panel box door knobs.
Using a moulding remover B, detach the 2 claws and remove the instrument panel box door knob.
55433B
33.REMOVE LOWER NO. 2 INSTRUMENT PANEL FINISH PANEL
Put protective tape around the lower No. 2 instrument panel finish panel.
Remove the 4 screws <C>.
| *a | Protective Tape |
| *b | Screw <C> |
Detach the 3 claws.
Disconnect the connector and remove the lower No. 2 instrument panel finish panel.
55660
34.REMOVE NO. 2 INSTRUMENT PANEL REGISTER ASSEMBLY
Put protective tape around the No. 2 instrument panel register assembly.
| *a | Protective Tape |
Detach the 4 claws and remove the No. 2 instrument panel register assembly.
55670
35.REMOVE NO. 3 INSTRUMENT PANEL REGISTER ASSEMBLY
for Type A:
Put protective tape around the No. 3 instrument panel register assembly.
| *a | Protective Tape |
Using moulding remover B, raise the No. 3 instrument panel register assembly.
Pull the No. 3 instrument panel register assembly by hand to detach the 7 claws and guide and remove the No. 3 instrument panel register assembly.
for Type B:
Put protective tape around the No. 3 instrument panel register assembly.
| *a | Protective Tape |
Using moulding remover B, raise the No. 3 instrument panel register assembly.
Pull the No. 3 instrument panel register assembly by hand to detach the 6 claws and remove the No. 3 instrument panel register assembly.
55680A
36.REMOVE NO. 4 INSTRUMENT PANEL REGISTER ASSEMBLY
for Type A:
Put protective tape around the No. 3 instrument panel register assembly.
| *a | Protective Tape |
Using moulding remover B, raise the No. 3 instrument panel register assembly.
Pull the No. 3 instrument panel register assembly by hand to detach the 7 claws and guide and remove the No. 3 instrument panel register assembly.
for Type B:
Put protective tape around the No. 3 instrument panel register assembly.
| *a | Protective Tape |
Using moulding remover B, raise the No. 3 instrument panel register assembly.
Pull the No. 3 instrument panel register assembly by hand to detach the 6 claws and remove the No. 3 instrument panel register assembly.
86110B
37.REMOVE MULTI-DISPLAY ASSEMBLY (w/ Navigation System)
55412C
38.REMOVE NO. 1 CENTER INSTRUMENT CLUSTER FINISH PANEL (w/o Navigation System)
for Type A:
Detach the 8 claws and 3 clips.
Disconnect the connectors and remove the No. 1 center instrument cluster finish panel.
for Type B:
Detach the 10 claws.
Disconnect the connectors and remove the No. 1 center instrument cluster finish panel.
55522B
39.REMOVE RADIO TUNER OPENING COVER (w/o Radio Receiver)
Remove the 2 bolts.
Remove the 2 screws and radio tuner opening cover.
86140A
40.REMOVE RADIO AND DISPLAY RECEIVER ASSEMBLY (for Radio and Display Type)
86120
41.REMOVE RADIO RECEIVER ASSEMBLY (for Radio Receiver Type)
86130A
42.REMOVE MULTI-MEDIA MODULE RECEIVER ASSEMBLY (w/ Navigation System)
43.REMOVE AIR CONDITIONING CONTROL ASSEMBLY (w/o Navigation System)
74610A
44.REMOVE ASSIST GRIP SUB-ASSEMBLY
62212
45.REMOVE FRONT PILLAR GARNISH LH
62211
46.REMOVE FRONT PILLAR GARNISH RH
55510F
47.REMOVE NO. 1 SPEAKER OPENING COVER ASSEMBLY
Put protective tape around the No. 1 speaker opening cover assembly.
| *a | Protective Tape |
Using a moulding remover A, detach the 8 clips and remove the No. 1 speaker opening cover assembly.
55408F
48.REMOVE NO. 1 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY
Put protective tape around the No. 1 instrument panel speaker panel sub-assembly.
| *a | Protective Tape |
Using a moulding remover A, detach the 3 claws and 2 guides and remove the No. 1 instrument panel speaker panel sub-assembly.
55409F
49.REMOVE NO. 2 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY
Put protective tape around the No. 2 instrument panel speaker panel sub-assembly.
| *a | Protective Tape |
Using a moulding remover A, detach the 3 claws and 2 guides and remove the No. 2 instrument panel speaker panel sub-assembly.
86160L
50.REMOVE FRONT NO. 4 SPEAKER ASSEMBLY (w/ Front Center Speaker)
86160P
51.REMOVE FRONT NO. 2 SPEAKER ASSEMBLY
Use the same procedure for the RH and LH sides (See page Audio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER>REMOVAL).
55405B
52.REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY
w/o Wireless Charger:
Detach the 6 claws.
Disconnect the connectors and remove the center instrument cluster finish panel sub-assembly.
w/ Wireless Charger:
Detach the 6 claws.
Disconnect the connectors and remove the center instrument cluster finish panel sub-assembly.
87212H
53.REMOVE REAR NO. 4 AIR DUCT (w/ Rear Air Duct)
Fold back the front floor carpet.
Detach the clip and remove the rear No. 4 air duct.
87212F
54.REMOVE REAR NO. 2 AIR DUCT (w/ Rear Air Duct)
Fold back the front floor carpet.
Detach the clip and remove the rear No. 2 air duct.
55400
55.REMOVE INSTRUMENT PANEL SAFETY PAD ASSEMBLY
Disconnect the connector and detach the clamps.
| *A | w/ Multi-terrian Monitor System | *B | w/ TOYOTA Parking Assist-sensor System |
Disconnect the connectors and detach the clamps.
Remove the bolt and disconnect the wire harness.
| *a | Connector | *b | Bolt |
Pull and slide the lock slider in the direction indicated by the arrow to release the connector lock and disconnect the passenger airbag connector.
When handling the passenger airbag connector, take care not to damage the airbag wire harness.
| *a | Lock Slider |
Disconnect the connectors.
Remove the 2 passenger airbag installation bolts <D>.
Remove the 6 bolts <E>.
Remove the 2 nuts <F>.
Remove the 2 bolts <B> and instrument panel safety pad assembly.
| *a | Passenger Airbag Connector | *b | Connector |
| *c | Passenger Airbag Installation Bolt <D> | *d | Bolt <E> |
| *e | Nut <F> | *f | Bolt <B> |