Home › Vehicle Interior › HEATING / AIR CONDITIONING › FRONT AIR CONDITIONING UNIT (for LHD) › from 2015.08
RM2660E _58 Vehicle Interior _052847 HEATING / AIR CONDITIONING _0255683 FRONT AIR CONDITIONING UNIT(for LHD) A

HEATING / AIR CONDITIONING  FRONT AIR CONDITIONING UNIT(for LHD)  REMOVAL  


CAUTION / NOTICE / HINT

NOTICE:

Set to recirculation mode before removing the air conditioning filter.


PROCEDURE

Hide 53806 1.REMOVE FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY LH

Hide 53805 2.REMOVE FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY RH

Hide 5.RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM

Hide 7. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 8.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 88710C 9.DISCONNECT AIR CONDITIONING TUBE ASSEMBLY

a.
E154197E02
1.822,0.396 2.017,0.573 0.195,0.177 10 *1 1.108,0.476 1.796,0.476 false

Remove the bolt.

Text in Illustration
*1 Plate


b.

Detach the plate as shown in the illustration.


c.
U166658E02
2.167,0.677 2.656,0.677 false 2.313,0.302 2.552,0.49 0.24,0.188 10 false *a

Disconnect the air conditioning tube assembly.

NOTICE:
·

Do not use a screwdriver or similar tool to disconnect the tube.

·

Seal the openings of the disconnected parts using vinyl tape to prevent moisture and foreign matter from entering them.



Text in Illustration
*a Disconnect tube by hand


d.

Remove the 2 O-rings from the air conditioning tube assembly.


Hide 87245A 10.DISCONNECT HEATER WATER INLET HOSE AND HEATER WATER OUTLET HOSE

a.

Using pliers, grip the claws of the clips and slide the 2 clips.


b.

Disconnect the 2 heater water hoses.

E247110E01
0.144,0.243 0.371,0.430 0.227,0.187 10 *A 3.927,0.243 4.154,0.430 0.227,0.187 10 *B 0.144,2.597 0.371,2.784 0.227,0.187 10 *C

Text in Illustration
*A for 1GR-FE *B for 1VD-FTV
*C for 1UR-FE, for 3UR-FE - -


Hide 11.REMOVE FRONT WIPER MOTOR AND BRACKET

Hide 55301 12.REMOVE INSTRUMENT PANEL SUB-ASSEMBLY

Hide 88576D 13.REMOVE NO. 2 COOLER AIR DUCT

Hide 87201F 14.REMOVE NO. 3 AIR DUCT SUB-ASSEMBLY

E156901

a.

Remove the clip.


b.

Detach the 2 claws and remove the duct.


Hide 45250 15.REMOVE STEERING COLUMN ASSEMBLY

Hide 55870B 16.REMOVE HEATER TO REGISTER DUCT ASSEMBLY

a.

Remove the 3 clips.


b.

Detach the 2 claws and remove the duct.

E154749


Hide 55330B 17.REMOVE INSTRUMENT PANEL REINFORCEMENT ASSEMBLY

a.

Disconnect the 17 clamps.


b.

Remove the 8 nuts, 6 bolts, connectors and wire harness

E154750


c.

Remove the instrument panel reinforcement.

i.

for Driver Side:

Remove the 3 caps and 3 bolts.


ii.

for Passenger Side:

Remove the 2 caps.


iii.

for Passenger Side:

Using a T40 "TORX" socket, remove the 2 "TORX" bolts.

HINT:

When removing the bolts, the collars may come off with the bolts.



iv.

for Passenger Side:

Using a 12 mm hexagon wrench, remove the 2 collars.


v.

Remove the 7 bolts, screw and instrument panel reinforcement.

E155488



Hide 88720A 18.REMOVE AIR CONDITIONING HOSE AND ACCESSORY (w/ Cool Box)

E154320

a.

Remove the bolt.


b.

Using SST, remove the piping clamp.

SST
09870-00025  

i.
E112919E02
2.348,1.375 2.677,1.545 0.330,0.170 10 SST 1.259,0.614 2.1,1.448 false 2.1,1.448 2.332,1.448 false

Attach SST to the piping clamp.

HINT:

Confirm the direction of the piping clamp claw and SST by referring to the illustration on the caution label.



ii.
E112920E04
3.011,1.476 2.547,1.914 false 2.547,1.914 2.353,1.914 false 0.651,0.155 0.839,0.352 0.188,0.198 10 *a 2.496,0.155 2.679,0.348 0.184,0.193 10 *b 2.166,1.819 2.341,2.003 0.174,0.184 10 *1 2.988,0.201 3.311,0.366 0.323,0.165 10 SST 1.407,0.166 1.730,0.331 0.323,0.165 10 SST 2.954,0.287 2.822,0.281 2.822,0.281 2.719,0.619 false 1.373,0.247 1.201,0.247 1.201,0.247 0.995,0.659 false

Push down SST and release the clamp lock.

NOTICE:

Be careful not to deform the tubes when pushing SST.



iii.

Pull SST slightly and push the release lever, then remove the piping clamp with SST.


iv.

Remove the piping clamp from SST.

Text in Illustration
*1 Release Lever
*a Push
*b Pull



c.

Disconnect the hose and accessory from the liquid tube to remove it.

NOTICE:

Cap the open fittings immediately to keep moisture or dirt out of the system.



d.

Remove the 2 O-rings from the air conditioner hose and accessory.


Hide 19.REMOVE AIR CONDITIONING UNIT

a.
E154751

Remove the 2 nuts and air conditioning unit.