Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM(w/ Navigation System) › 2014.08–2015.08
RM2660E _56 Audio / Visual / Telematics _052828 AUDIO / VIDEO _0255478 AUDIO AND VISUAL SYSTEM(w/ Navigation System) C

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(w/ Navigation System)  B15D0  MOST Communication Malfunction  


DESCRIPTION

This DTC is stored when the MOST network cannot be established after the master unit is activated.

HINT:
·

If a short occurs in a speaker circuit, the sound from the corresponding speaker will be low or almost impossible to hear. If the volume is turned up in this situation, to prevent excessive current flow due to the short circuit, the stereo component amplifier assembly stops operating when its output exceeds a certain level. When the operation of the stereo component amplifier assembly stops, the audio and visual system will not function normally. This is because MOST communication will stop due to the shut down of the amplifier causing an error in the MOST network. The stereo component amplifier assembly will start operating again when the engine switch is turned off and back on (ACC) again. However, the amplifier will stop operating again if its output exceeds a certain level.

·

When the stereo component amplifier assembly stops operating and a malfunction occurs in the audio and visual system due to a short in a speaker circuit, this DTC will be stored.



DTC Code DTC Detection Condition Trouble Area
B15D0 MOST network cannot be established.
·

MOST line check

·

MOST communication line connector

·

MOST communication line

·

Stereo component amplifier assembly

·

Multi-media module receiver assembly

·

Television display assembly*



*: w/ Rear Seat Entertainment System


HINT:
·

For the MOST network, the multi-media module receiver assembly is the master unit.

·

Errors may occur in MOST communication between devices due to problems such as electrical noise.



WIRING DIAGRAM

E248724E01
0.494,6.827 3.165,7.022 2.671,0.195 10 *1: w/o Rear Seat Entertainment System 0.494,7.087 3.056,7.282 2.562,0.195 10 *2: w/ Rear Seat Entertainment System 1.081,7.352 2.941,7.536 1.860,0.184 10 : MOST Network 1.702,2.959 1.899,3.129 0.198,0.170 10 6 1.702,3.379 1.899,3.549 0.198,0.170 10 7 1.702,2.51 1.899,2.681 0.198,0.170 10 5 4.181,4.871 4.379,5.041 0.198,0.170 10 6 4.195,5.319 4.393,5.490 0.198,0.170 10 7 4.181,4.409 4.379,4.579 0.198,0.170 10 5 5.645,2.959 5.749,3.129 0.103,0.170 10 3 5.645,3.358 5.843,3.528 0.198,0.170 10 4 5.645,2.503 5.843,2.674 0.198,0.170 10 2 1.709,2.055 1.906,2.225 0.198,0.170 10 8 3.264,5.34 3.461,5.511 0.198,0.170 10 4 3.264,4.878 3.461,5.048 0.198,0.170 10 3 3.271,4.423 3.468,4.593 0.198,0.170 10 2 5.681,5.312 5.878,5.483 0.198,0.170 10 4 5.681,4.85 5.878,5.020 0.198,0.170 10 3 5.688,4.395 5.885,4.565 0.198,0.170 10 2 3.264,4.065 3.461,4.236 0.198,0.170 10 8 1.681,4.85 1.878,5.020 0.198,0.170 10 6 1.681,5.312 1.878,5.483 0.198,0.170 10 7 1.681,4.402 1.878,4.572 0.198,0.170 10 5 1.695,4.065 1.892,4.236 0.198,0.170 10 1 5.645,2.055 5.843,2.225 0.198,0.170 10 1 1.681,1.144 1.878,1.315 0.198,0.170 10 3 1.681,1.621 1.878,1.791 0.198,0.170 10 4 1.681,0.696 1.878,0.866 0.198,0.170 10 2 0.711,2.753 0.909,2.923 0.198,0.170 10 *1 0.75,4.861 0.947,5.031 0.198,0.170 10 *2 5.624,1.172 5.749,1.343 0.125,0.170 10 6 5.624,1.649 5.822,1.819 0.198,0.170 10 7 1.275,2.111 1.584,2.281 0.309,0.170 10 WUI 1.254,2.619 1.583,2.789 0.330,0.170 10 MO+ 1.275,3.067 1.584,3.238 0.309,0.170 10 MO- 1.166,3.474 1.583,3.644 0.416,0.170 10 SLDO 1.205,4.128 1.583,4.299 0.378,0.170 10 WUO 1.243,4.51 1.583,4.681 0.340,0.170 10 MO+ 1.278,4.973 1.584,5.143 0.305,0.170 10 MO- 1.17,5.421 1.583,5.591 0.413,0.170 10 SLDO 3.439,4.135 3.817,4.306 0.378,0.170 10 WUI 3.44,4.517 3.818,4.688 0.378,0.170 10 MI+ 3.433,5.022 3.811,5.192 0.378,0.170 10 MI- 3.412,5.428 3.859,5.598 0.448,0.170 10 SLDI 3.818,4.503 4.196,4.674 0.378,0.170 10 MO+ 3.839,4.966 4.217,5.136 0.378,0.170 10 MO- 3.762,5.428 4.209,5.598 0.448,0.170 10 SLDO 1.229,1.708 1.583,1.879 0.354,0.170 10 SLDI 1.317,1.253 1.584,1.423 0.267,0.170 10 MI- 1.317,0.805 1.584,0.975 0.267,0.170 10 MI+ 5.87,2.125 6.248,2.295 0.378,0.170 10 WUO 5.87,2.605 6.248,2.775 0.378,0.170 10 MI+ 5.87,3.067 6.248,3.238 0.378,0.170 10 MI- 5.87,3.474 6.318,3.644 0.448,0.170 10 SLDI 5.87,1.736 6.339,1.907 0.468,0.170 10 SLDO 5.87,1.281 6.248,1.451 0.378,0.170 10 MO+ 5.87,0.833 6.248,1.003 0.378,0.170 10 MO+ 5.87,5.414 6.248,5.584 0.378,0.170 10 SLDI 5.87,4.973 6.248,5.143 0.378,0.170 10 MI- 5.87,4.51 6.248,4.681 0.378,0.170 10 MI+ 5.624,0.71 5.822,0.880 0.198,0.170 10 5 0.221,6.278 2.662,6.474 2.442,0.195 10 Stereo Component Amplifier Assembly 5.735,6.4 7.095,6.785 1.360,0.385 10 Multi-media Module Receiver Assembly 5.735,6.222 6.090,6.434 0.355,0.211 10 F84 3.283,6.134 4.643,6.519 1.360,0.385 10 Television Display Assembly*2 3.283,5.956 3.638,6.168 0.355,0.211 10 L56 0.221,6.115 0.576,6.326 0.355,0.211 10 F85 3.936,1.839 4.549,2.009 0.614,0.170 10 Shielded 2.829,1.839 3.443,2.009 0.614,0.170 10 Shielded 3.922,3.59 4.535,3.760 0.614,0.170 10 Shielded 2.815,3.59 3.429,3.760 0.614,0.170 10 Shielded 1.82,5.575 2.434,5.745 0.614,0.170 10 Shielded 2.661,5.575 3.274,5.745 0.614,0.170 10 Shielded 4.323,5.575 4.937,5.745 0.614,0.170 10 Shielded 5.145,5.575 5.759,5.745 0.614,0.170 10 Shielded 0.96,2.423 6.403,3.768 5.443,1.345 0.96,4.018 6.403,5.79 5.443,1.772 0.96,4.018 6.403,5.79 5.443,1.772

PROCEDURE

1.CHECK OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)
a.

Check that optional components (including associated wiring) which generate radio waves are not installed.

Result
Result Proceed to
Optional components (including associated wiring) are installed. A
Optional components (including associated wiring) are installed.
DTCs are not output.
B

HINT:
·

Electrical noise from radio waves generated by optional components or the wiring for those components may affect AVC-LAN communication.

·

These DTCs may be stored when an AVC-LAN communication error occurs due to electrical noise.





A

2.CONFIRM SYMPTOMS

B

3.CHECK MOST COMMUNICATION CONNECTORS
2.CONFIRM SYMPTOMS
a.

Turn the engine switch off.


b.

Turn the engine switch on (ACC) and check if the audio system activates and if the speakers operate.

HINT:
·

Choose a source such as radio so that sound can be output from the speakers.

·

If sound from the speakers is low, turn up the volume.



Result
Result Proceed to
Even after the engine switch is turned on (ACC), the audio system does not activate and sound is not output from the speakers (w/o Rear Seat Entertainment System). A
Even after the engine switch is turned on (ACC), the audio system does not activate and sound is not output from the speakers (w/ Rear Seat Entertainment System). B
The audio system activates when the engine switch is turned on (ACC) but the sound stops being output when the amplifier output exceeds a certain level. C

HINT:
·

If a short occurs in a speaker circuit, the sound from the corresponding speaker will be low or almost impossible to hear. If the volume is turned up in this situation, to prevent excessive current flow due to the short circuit, the stereo component amplifier assembly stops operating when its output exceeds a certain level. When the operation of the stereo component amplifier assembly stops, the audio and visual system will not function normally. This is because MOST communication will stop due to the shut down of the amplifier causing an error in the MOST network. The stereo component amplifier assembly will start operating again when the engine switch is turned off and back on (ACC) again. However, the amplifier will stop operating again if its output exceeds a certain level.

·

When the stereo component amplifier assembly stops operating and a malfunction occurs in the audio and visual system due to a short in a speaker circuit, this DTC will be stored. In this case, check each speaker circuit and repair or replace malfunctioning parts, and then recheck for DTCs.





A

3.CHECK MOST COMMUNICATION CONNECTORS

B

11.CHECK MOST COMMUNICATION CONNECTORS

C

3.CHECK MOST COMMUNICATION CONNECTORS
a.
C253083E01
1.104,1.834 1.276,2.013 0.172,0.179 10 *c 0.76,1.834 0.932,2.013 0.172,0.179 10 *b 0.416,1.834 0.588,2.013 0.172,0.179 10 *a 0.812,0.899 0.885,1.856 false 1.156,0.899 1.229,1.856 false 0.588,0.899 0.541,1.856 false

Display the "MOST Line Check" screen (See page Audio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM(w/ Navigation System)>DTC CHECK / CLEAR).


b.

Check the result on the "MOST Line Check" screen.

Result
Result Proceed to
"NCON" is displayed for "AMP". A
"OK" is displayed for all items. B

·

When "NCON" is displayed for more than 1 item, proceed to the step for the device that has the smallest node position number.

·

The "MOST Line Check" screen can be displayed only when DTC B15D0 is stored.


Text in Illustration
*a Node position number for devices that use MOST communication
*b Device name
*c Result



A

4.CONFIRM SYMPTOMS

B

7.CHECK HARNESS AND CONNECTOR (MULTI-MEDIA MODULE RECEIVER ASSEMBLY - STEREO COMPONENTAMPLIFIER ASSEMBLY)
4.CONFIRM SYMPTOMS
a.

Check the MOST communication line connectors.

i.

Check if the MOST communication line connector between the multi-media module receiver assembly and stereo component amplifier assembly has any connection problems (See page General>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE).



b.

Display the "MOST Line Check" screen and check the result (See page Audio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM(w/ Navigation System)>DTC CHECK / CLEAR).

Result
Result Proceed to
"NCON" is displayed for "AMP". A
The screen cannot be changed to the "MOST Line Check" screen. B

HINT:

When the malfunction in the MOST network is repaired, the screen cannot be changed to the "MOST Line Check" screen.




A

5.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY WAKE UP LINE)

B

5.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY WAKE UP LINE)
a.
U166257E01
0.091,0.042 0.289,0.209 0.198,0.167 10 *a 0.907,1.847 1.247,2.014 0.340,0.167 10 WUI 1.592,0.279 1.924,0.456 0.332,0.177 10 F85 1.684,1.522 1.241,1.844 false

Disconnect the stereo component amplifier assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F85-8 (WUI) - Body ground Engine switch on (ACC) 4.5 V or higher


Text in Illustration
*a Front view of wire harness connector
(to Stereo Component Amplifier Assembly)



OK

REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY

NG

6.CHECK HARNESS AND CONNECTOR (MULTI-MEDIA MODULE RECEIVER ASSEMBLY - STEREO COMPONENT AMPLIFIER ASSEMBLY)
6.CHECK HARNESS AND CONNECTOR (MULTI-MEDIA MODULE RECEIVER ASSEMBLY - STEREO COMPONENT AMPLIFIER ASSEMBLY)
a.

Disconnect the F84 multi-media module receiver assembly connector.


b.

Disconnect the F85 stereo component amplifier assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F84-1 (WUO) - F85-8 (WUI) Always Below 1 Ω
F84-1 (WUO) - Body ground Always 10 kΩ or higher




OK

7.CHECK HARNESS AND CONNECTOR (MULTI-MEDIA MODULE RECEIVER ASSEMBLY - STEREO COMPONENTAMPLIFIER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (MULTI-MEDIA MODULE RECEIVER ASSEMBLY - STEREO COMPONENTAMPLIFIER ASSEMBLY)
a.

Disconnect the F84 multi-media module receiver assembly connector.


b.

Disconnect the F85 stereo component amplifier assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F84-2 (MI+) - F85-5 (MO+) Always Below 1 Ω
F84-3 (MI-) - F85-6 (MO-) Always Below 1 Ω
F84-4 (SLDI) - F85-7 (SLDO) Always Below 1 Ω
F84-5 (MO+) - F85-2 (MI+) Always Below 1 Ω
F84-6 (MO-) - F85-3 (MI-) Always Below 1 Ω
F84-7 (SLDO) - F85-4 (SLDI) Always Below 1 Ω
F84-2 (MI+) - Body ground Always 10 kΩ or higher
F84-3 (MI-) - Body ground Always 10 kΩ or higher
F84-4 (SLDI) - Body ground Always 10 kΩ or higher
F84-5 (MO+) - Body ground Always 10 kΩ or higher
F84-6 (MO-) - Body ground Always 10 kΩ or higher
F84-7 (SLDO) - Body ground Always 10 kΩ or higher




OK

8.REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY
a.

Replace the stereo component amplifier assembly with a new or normally functioning one (See page Audio / Visual / Telematics>AUDIO / VIDEO>STEREO COMPONENT AMPLIFIER>REMOVAL).



NEXT

9.CLEAR DTC
10.CHECK DTC
a.

Recheck for DTCs and check if the same DTC is output again (See page Audio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM(w/ Navigation System)>DTC CHECK / CLEAR).

OK:

No DTCs are output.




OK

END (STEREO COMPONENT AMPLIFIER ASSEMBLY IS DEFECTIVE)

NG

REPLACE MULTI-MEDIA MODULE RECEIVER ASSEMBLY

11.CHECK MOST COMMUNICATION CONNECTORS
a.
E248723E01
0.506,1.918 0.668,2.079 0.162,0.161 10 *a 0.608,1.107 0.608,1.9 false 0.792,1.918 0.954,2.079 0.162,0.161 10 *b 0.895,1.091 0.895,1.916 false 1.079,1.918 1.240,2.079 0.162,0.161 10 *c 1.181,1.096 1.181,1.906 false

Display the "MOST Line Check" screen (See page Audio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM(w/ Navigation System)>DTC CHECK / CLEAR).


b.

Check the result on the "MOST Line Check" screen.

Result
Result Proceed to
"NCON" is displayed for "AMP". A
"NCON" is displayed for "RSE". B
"OK" is displayed for all items. C

·

When "NCON" is displayed for more than 1 item, proceed to the step for the device that has the smallest node position number.

·

The "MOST Line Check" screen can be displayed only when DTC B15D0 is stored.


Text in Illustration
*a Node position number for devices that use MOST communication
*b Device name
*c Result



A

12.CONFIRM SYMPTOMS

B

15.CONFIRM SYMPTOMS

C

18.CHECK HARNESS AND CONNECTOR (MULTI-MEDIA MODULE RECEIVER ASSEMBLY - STEREO COMPONENT AMPLIFIER ASSEMBLY)
12.CONFIRM SYMPTOMS
a.

Check the MOST communication line connectors.

i.

Check if the MOST communication line connector between the multi-media module receiver assembly and stereo component amplifier assembly has any connection problems (See page General>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING).



b.

Display the "MOST Line Check" screen and check the result (See page Audio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM(w/ Navigation System)>DTC CHECK / CLEAR).

Result
Result Proceed to
"NCON" is displayed for "AMP". A
The screen cannot be changed to the "MOST Line Check" screen. B

HINT:

When the malfunction in the MOST network is repaired, the screen cannot be changed to the "MOST Line Check" screen.




A

13.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY WAKE UP LINE)

B

13.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY WAKE UP LINE)
a.
U166257E01
0.091,0.042 0.289,0.209 0.198,0.167 10 *a 0.907,1.847 1.247,2.014 0.340,0.167 10 WUI 1.592,0.279 1.924,0.456 0.332,0.177 10 F85 1.684,1.522 1.241,1.844 false

Disconnect the stereo component amplifier assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F85-8 (WUI) - Body ground Engine switch on (ACC) 4.5 V or higher


Text in Illustration
*a Front view of wire harness connector
(to Stereo Component Amplifier Assembly)



OK

REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY

NG

14.CHECK HARNESS AND CONNECTOR (MULTI-MEDIA MODULE RECEIVER ASSEMBLY - STEREO COMPONENT AMPLIFIER ASSEMBLY)
14.CHECK HARNESS AND CONNECTOR (MULTI-MEDIA MODULE RECEIVER ASSEMBLY - STEREO COMPONENT AMPLIFIER ASSEMBLY)
a.

Disconnect the F84 multi-media module receiver assembly connector.


b.

Disconnect the F85 stereo component amplifier assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F84-1 (WUO) - F85-8 (WUI) Always Below 1 Ω
F84-1 (WUO) - Body ground Always 10 kΩ or higher




OK

REPLACE MULTI-MEDIA MODULE RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

15.CONFIRM SYMPTOMS
a.

Check the MOST communication line connectors.

i.

Check if the MOST communication line connector between the multi-media module receiver assembly and stereo component amplifier assembly has any connection problems (See page General>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING).



b.

Display the "MOST Line Check" screen and check the result (See page Audio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM(w/ Navigation System)>DTC CHECK / CLEAR).

Result
Result Proceed to
"NCON" is displayed for "RSE". A
The screen cannot be changed to the "MOST Line Check" screen. B

HINT:

When the malfunction in the MOST network is repaired, the screen cannot be changed to the "MOST Line Check" screen.




A

16.CHECK HARNESS AND CONNECTOR (TELEVISION DISPLAY ASSEMBLY WAKE UP LINE)

B

16.CHECK HARNESS AND CONNECTOR (TELEVISION DISPLAY ASSEMBLY WAKE UP LINE)
a.
U166258E01
0.091,0.042 0.289,0.209 0.198,0.167 10 *a 0.907,1.847 1.247,2.014 0.340,0.167 10 WUI 1.592,0.279 1.924,0.456 0.332,0.177 10 L56 1.684,1.522 1.241,1.844 false

Disconnect the television display assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
L56-8 (WUI) - Body ground Engine switch on (ACC) 4.5 V or higher


Text in Illustration
*a Front view of wire harness connector
(to Television Display Assembly)



OK

REPLACE TELEVISION DISPLAY ASSEMBLY

NG

17.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - TELEVISION DISPLAY ASSEMBLY)
17.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - TELEVISION DISPLAY ASSEMBLY)
a.

Disconnect the F85 stereo component amplifier assembly connector.


b.

Disconnect the L56 television display assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F85-1 (WUO) - L56-8 (WUI) Always Below 1 Ω
F85-1 (WUO) - Body ground Always 10 kΩ or higher




OK

REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

18.CHECK HARNESS AND CONNECTOR (MULTI-MEDIA MODULE RECEIVER ASSEMBLY - STEREO COMPONENT AMPLIFIER ASSEMBLY)
a.

Disconnect the F84 multi-media module receiver assembly connector.


b.

Disconnect the F85 stereo component amplifier assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F84-2 (MI+) - F85-5 (MO+) Always Below 1 Ω
F84-3 (MI-) - F85-6 (MO-) Always Below 1 Ω
F84-4 (SLDI) - F85-7 (SLDO) Always Below 1 Ω
F84-5 (MO+) - F85-2 (MI+) Always Below 1 Ω
F84-6 (MO-) - F85-3 (MI-) Always Below 1 Ω
F84-7 (SLDO) - F85-4 (SLDI) Always Below 1 Ω
F84-2 (MI+) - Body ground Always 10 kΩ or higher
F84-3 (MI-) - Body ground Always 10 kΩ or higher
F84-4 (SLDI) - Body ground Always 10 kΩ or higher
F84-5 (MO+) - Body ground Always 10 kΩ or higher
F84-6 (MO-) - Body ground Always 10 kΩ or higher
F84-7 (SLDO) - Body ground Always 10 kΩ or higher




OK

19.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - TELEVISION DISPLAY ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

19.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - TELEVISION DISPLAY ASSEMBLY)
a.

Disconnect the F85 stereo component amplifier assembly connector.


b.

Disconnect the L56 television display assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F85-5 (MO+) - L56-2 (MI+) Always Below 1 Ω
F85-6 (MO-) - L56-3 (MI-) Always Below 1 Ω
F85-7 (SLDO) - L56-4 (SLDI) Always Below 1 Ω
F85-5 (MO+) - Body ground Always 10 kΩ or higher
F85-6 (MO-) - Body ground Always 10 kΩ or higher
F85-7 (SLDO) - Body ground Always 10 kΩ or higher




OK

20.CHECK HARNESS AND CONNECTOR (MULTI-MEDIA MODULE RECEIVER ASSEMBLY - TELEVISION DISPLAY ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

20.CHECK HARNESS AND CONNECTOR (MULTI-MEDIA MODULE RECEIVER ASSEMBLY - TELEVISION DISPLAY ASSEMBLY)
a.

Disconnect the F84 multi-media module receiver assembly connector.


b.

Disconnect the L56 television display assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F84-2 (MI+) - L56-5 (MO+) Always Below 1 Ω
F84-3 (MI-) - L56-6 (MO-) Always Below 1 Ω
F84-4 (SLDI) - L56-7 (SLDO) Always Below 1 Ω
F84-2 (MI+) - Body ground Always 10 kΩ or higher
F84-3 (MI-) - Body ground Always 10 kΩ or higher
F84-4 (SLDI) - Body ground Always 10 kΩ or higher




OK

21.CLEAR DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

22.CHECK DTC
a.

Recheck for DTCs and check if the same DTC is output again (See page Audio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM(w/ Navigation System)>DTC CHECK / CLEAR).

OK:

No DTCs are output.




OK

NG

REPLACE MULTI-MEDIA MODULE RECEIVER ASSEMBLY