| DTC No. | DTC Detection Condition | Trouble Area |
|---|---|---|
| 74-40 | Short is detected in the speaker output circuit. | ·
Harness or connector ·
Speaker ·
Stereo component amplifier assembly |
After the inspection is completed, clear the DTCs.
Disconnect the F3 and F52 amplifier connectors.
Clear the DTCs.
Check if DTC 74-40 is output.
DTC 74-40 is not output.
OK
NG
Reconnect the F52 amplifier connector.
Clear the DTCs.
Check if DTC 74-40 is output.
DTC 74-40 is not output.
OK
NG
Disconnect the F3 amplifier connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F3-8 (CTR+) - Body ground | Always | 10 kΩ or higher |
| F3-7 (CTR-) - Body ground | Always | 10 kΩ or higher |
| F3-1 (WFL+) - Body ground | Always | 10 kΩ or higher |
| F3-5 (WFL-) - Body ground | Always | 10 kΩ or higher |
| F3-2 (WFR+) - Body ground | Always | 10 kΩ or higher |
| F3-6 (WFR-) - Body ground | Always | 10 kΩ or higher |
OK
NG
Disconnect the I10 and I1 speaker connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 - 2 | Always | 3 Ω |
| *1 | Component without harness connected
(Front No. 1 Speaker) |
OK
NG
Disconnect the F6 speaker connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 - 2 | Always | 6 Ω |
| *1 | Component without harness connected
(Front No. 4 Speaker) |
OK
NG
Disconnect the F52 amplifier connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F52-8 (FL-) - Body ground | Always | 10 kΩ or higher |
| F52-3 (FL+) - Body ground | Always | 10 kΩ or higher |
| F52-9 (FR-) - Body ground | Always | 10 kΩ or higher |
| F52-10 (FR+) - Body ground | Always | 10 kΩ or higher |
| F52-5 (RR+) - Body ground | Always | 10 kΩ or higher |
| F52-12 (RR-) - Body ground | Always | 10 kΩ or higher |
| F52-4 (RL+) - Body ground | Always | 10 kΩ or higher |
| F52-11 (RL-) - Body ground | Always | 10 kΩ or higher |
OK
NG
Disconnect the J17 and J15 speaker connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 - 2 | Always | 4 Ω |
| *1 | Component without harness connected
(Rear Speaker Set) |
OK
NG
Disconnect the F8 and F7 speaker connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 - 2 | Always | Below 1 Ω |
| 3 - 4 | Always | Below 1 Ω |
| 2 - 4 | Always | 4 Ω |
| *1 | Component without harness connected
(Front No. 2 Speaker) |
OK
NG
Disconnect the F14 and F13 speaker connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 - 2 | Always | 4 Ω |
| *1 | Component without harness connected
(Front No. 3 Speaker) |
OK
NG
Disconnect the F8, F7, F14 and F13 speaker connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F8-2 (TWL+) - F14-1 | Always | Below 1 Ω |
| F8-4 (TWL-) - F14-2 | ||
| F8-2 (TWL+) - Body ground | Always | 10 kΩ or higher |
| F8-4 (TWL-) - Body ground |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F7-2 (TWR+) - F13-1 | Always | Below 1 Ω |
| F7-4 (TWR-) - F13-2 | ||
| F7-2 (TWR+) - Body ground | Always | 10 kΩ or higher |
| F7-4 (TWR-) - Body ground |
OK
NG