Home › Power Source / Network › POWER DISTRIBUTION › MAIN BODY ECU (for LHD) › from 2015.08
RM2660E _57 Power Source / Network _052836 POWER DISTRIBUTION _0255530 MAIN BODY ECU(for LHD) A

POWER DISTRIBUTION  MAIN BODY ECU(for LHD)  INSTALLATION  


PROCEDURE

Hide 89221 1.INSTALL MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NOTICE:
·

If the main body ECU (multiplex network body ECU) is replaced, refer to service bulletin.

·

Make sure that the connecting surfaces are free of foreign matter.

·

Do not touch the main body ECU (multiplex network body ECU) connector.



a.
E333966E01
0.291,2.147 0.482,2.319 0.191,0.172 10 *a

Insert the main body ECU (multiplex network body ECU) up to the position where it contacts the housing sidewall as shown in the illustration.

Text in Illustration
*a 20°
V100136

Insert
V100155

Housing Sidewall

HINT:

Make sure to keep the angle 20° or more as shown in the illustration.



b.
E333967

Slide the main body ECU (multiplex network body ECU) along the housing sidewall so that it attaches to the 2 guides.

Text in Illustration
V100135

Slide
V100155

Housing Sidewall


c.
E333968E01
2.675,0.739 2.872,0.911 0.198,0.172 10 *a 2.239,1.38 2.675,0.876 false

While keeping the main body ECU (multiplex network body ECU) in contact with side A of the cowl side junction block LH (axis of rotation), rotate it downward as shown in the illustration.

Text in Illustration
*a Side A Contact Portion


d.
E333969

Press the push area until the claw engages to install the main body ECU (multiplex network body ECU).

Text in Illustration
V100155

Push Area

NOTICE:
·

Make sure to press only the push area.

·

Confirm the engagement of the main body ECU (multiplex network body ECU) and cowl side junction block LH by listening for the "click" sound of the lock engaging.



HINT:

If a "click" sound cannot be heard, visually check the engagement of the lock. The engagement can also be confirmed if the main body ECU (multiplex network body ECU) and cowl side junction block LH are flush.



Hide 82673A 2.INSTALL JUNCTION BLOCK BRACKET

a.

Attach the guide to install the junction block bracket.


b.

Install the bolt.

Torque:
7.6 N*m (77 kgf*cm, 67 in.*lbf)


Hide 82733A 4.INSTALL COWL SIDE JUNCTION BLOCK LH

a.
E333970

Connect the connector with lock lever.

i.

Connect the connector.


ii.

Push the lock lever to attach the claw.



b.
E333971

Slide the connector lock to attach the claw.


c.
E333972

Connect the connector with lock lever.

i.

Connect the connector.


ii.

Push the lock lever to attach the claw.



d.

Install the cowl side junction block LH with the 2 nuts and bolt.

Torque:
for Nut : 7.6 N*m (77 kgf*cm, 67 in.*lbf)
for Bolt : 7.6 N*m (77 kgf*cm, 67 in.*lbf)


e.
E333973E01
3.021,2.846 3.267,3.037 0.246,0.191 12 *A

Connect the connector with lock lever.

Text in Illustration
*A w/ VGRS
V100135

Connector
V100137

Connector with Lock Lever

HINT:

Use the same procedure to connect the connector with lock lever on the other side.


i.

Connect the connector.


ii.

Push the lock lever to attach the claw.



f.

Connect each connector.


Hide 55303B 5.INSTALL LOWER INSTRUMENT PANEL SUB-ASSEMBLY (w/o Driver Side Knee Airbag)

Hide 73900 6.INSTALL DRIVER SIDE KNEE AIRBAG ASSEMBLY (w/ Driver Side Knee Airbag)

Hide 55432D 7.INSTALL LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL

Hide 55606 9.INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (w/ Cover)

Hide 55475A 10.INSTALL NO. 2 INSTRUMENT CLUSTER FINISH PANEL GARNISH

Hide 55474C 11.INSTALL NO. 1 INSTRUMENT CLUSTER FINISH PANEL GARNISH

Hide 55403C 12.INSTALL LOWER INSTRUMENT PANEL PAD SUB-ASSEMBLY LH

Hide 55449C 13.INSTALL NO. 2 INSTRUMENT PANEL FINISH PANEL CUSHION

Hide 16.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).