Home › Vehicle Interior › INTERIOR PANELS / TRIM › INSTRUMENT PANEL SAFETY PAD › 2015.08–2016.08
RM2660E _58 Vehicle Interior _052849 INTERIOR PANELS / TRIM _0255717 INSTRUMENT PANEL SAFETY PAD A

INTERIOR PANELS / TRIM  INSTRUMENT PANEL SAFETY PAD  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.

·

A bolt without a torque specification is shown in the standard bolt chart (See page General>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS).



PROCEDURE

Hide 55400 1.INSTALL INSTRUMENT PANEL SAFETY PAD ASSEMBLY

a.

Install the instrument panel safety pad assembly with the 6 bolts <E>, 2 nuts <F> and 2 bolts <B>.


b.

Install the 2 passenger airbag installation bolts <D>.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


c.

Connect the connectors.

U156001E03
1.135,1.063 1.323,1.24 0.188,0.177 10 false *f 1.25,0.854 1.438,1.031 0.188,0.177 10 true *e 1.875,0.333 2.063,0.51 0.188,0.177 10 true *d 0.813,0.615 1,0.792 0.188,0.177 10 true *d 1.823,0.958 2.01,1.135 0.188,0.177 10 true *e 6.656,1.458 6.844,1.635 0.188,0.177 10 false *a 0.25,3.24 0.438,3.417 0.188,0.177 10 false *a 5.115,2.604 5.302,2.781 0.188,0.177 10 false *a 4.76,3.354 4.948,3.531 0.188,0.177 10 false *a 6.469,2.229 6.656,2.406 0.188,0.177 10 false *a 1.344,4.438 1.531,4.615 0.188,0.177 10 false *c 6.333,2.979 6.521,3.156 0.188,0.177 10 false *c 3.146,2.792 3.333,2.969 0.188,0.177 10 true *b 3.083,3.75 3.271,3.927 0.188,0.177 10 false *a 2.281,2.885 2.469,3.063 0.188,0.177 10 false *b

Text in Illustration
*a Bolt <E> *b Nut <F>
*c Bolt <B> *d Passenger Airbag Installation Bolt <D>
*e Connector *f Passenger Airbag Connector


d.
U155893E01
1.813,0.252 2.004,0.431 0.192,0.179 10 *a 2.736,0.237 2.927,0.416 0.192,0.179 10 *b 1.78,0.926 1.888,0.446 false 2.719,0.915 2.827,0.436 false

Connect the passenger airbag connector.

NOTICE:

When handling the passenger airbag connector, take care not to damage the airbag wire harness.



e.

Check that the lock slider is in the lock position.

Text in Illustration
*a Lock Slider
*b Lock Position


f.

Connect the connectors and attach the clamps.


g.

Connect the wire harness with the bolt.

U155757E01
6.771,1.083 6.958,1.26 0.188,0.177 10 true *a 6.792,0.833 6.979,1.01 0.188,0.177 10 true *b 6.771,1.302 6.958,1.479 0.188,0.177 10 true *a 6.75,1.573 6.938,1.75 0.188,0.177 10 true *a 4.25,5 4.438,5.177 0.188,0.177 10 true *a 4.323,5.323 4.51,5.5 0.188,0.177 10 true *a 6.76,5.375 6.948,5.552 0.188,0.177 10 true *b 3.073,5.427 3.26,5.604 0.188,0.177 10 true *a

Text in Illustration
*a Connector *b Bolt


h.

Connect the connectors and attach the clamps.

U164418E01
1.216,1.711 1.407,1.890 0.192,0.179 10 *A 4.307,1.719 4.499,1.898 0.192,0.179 10 *B

Text in Illustration
*A w/ Multi-terrian Monitor System *B w/ TOYOTA Parking Assist-sensor System


Hide 87212H 2.INSTALL REAR NO. 4 AIR DUCT (w/ Rear Air Duct)

B180308

a.

Attach the clip to install the rear No. 4 air duct.


Hide 87212F 3.INSTALL REAR NO. 2 AIR DUCT (w/ Rear Air Duct)

B180309

a.

Attach the clip to install the rear No. 2 air duct.


Hide 55405B 4.INSTALL CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY

a.

w/o Wireless Charger:

i.
B432518

Connect the connectors.


ii.

Attach the 6 claws to install the center instrument cluster finish panel sub-assembly.



b.

w/ Wireless Charger:

i.
B432519

Connect the connectors.


ii.

Attach the 6 claws to install the center instrument cluster finish panel sub-assembly.



Hide 86160P 5.INSTALL FRONT NO. 2 SPEAKER ASSEMBLY

HINT:

Use the same procedure for the RH and LH sides (See page Audio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER>INSTALLATION).


Hide 86160L 6.INSTALL FRONT NO. 4 SPEAKER ASSEMBLY (w/ Front Center Speaker)

Hide 55408F 7.INSTALL NO. 1 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY

B421869

a.

Attach the 2 guides.


b.

Attach the 3 claws to install the No. 1 instrument panel speaker panel sub-assembly.


Hide 55409F 8.INSTALL NO. 2 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY

B421867

a.

Attach the 2 guides.


b.

Attach the 3 claws to install the No. 2 instrument panel speaker panel sub-assembly.


Hide 55510F 9.INSTALL NO. 1 SPEAKER OPENING COVER ASSEMBLY

B421865

a.

Attach the 8 clips to install the No. 1 speaker opening cover assembly.


Hide 86130A 13.INSTALL MULTI-MEDIA MODULE RECEIVER ASSEMBLY (w/ Navigation System)

Hide 55522B 16.INSTALL RADIO TUNER OPENING COVER (w/o Radio Receiver)

B180654

a.

Install the radio tuner opening cover with the 2 bolts and 2 screws.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


Hide 86120 17.INSTALL RADIO RECEIVER ASSEMBLY (for Radio Receiver Type)

Hide 86140A 18.INSTALL RADIO AND DISPLAY RECEIVER ASSEMBLY (for Radio and Display Type)

Hide 55412C 19.INSTALL NO. 1 CENTER INSTRUMENT CLUSTER FINISH PANEL (w/o Navigation System)

B421870

a.

for Type A:

i.

Connect the connector.


ii.

Attach the 8 claws and 3 clips to install the No. 1 center instrument cluster finish panel.



b.

for Type B:

i.
B180653

Connect the connector.


ii.

Attach the 10 claws to install the No. 1 center instrument cluster finish panel.



Hide 55670 20.INSTALL NO. 3 INSTRUMENT PANEL REGISTER ASSEMBLY

a.

for Type A:

i.
B432535

Attach the guide and 7 claws to install the No. 3 instrument panel register assembly.



b.

for Type B:

i.
B435724

Attach the 6 claws to install the No. 3 instrument panel register assembly.



Hide 55680A 21.INSTALL NO. 4 INSTRUMENT PANEL REGISTER ASSEMBLY

a.

for Type A:

i.
B432536

Attach the guide and 7 claws to install the No. 4 instrument panel register assembly.



b.

for Type B:

i.
B435725

Attach the 6 claws to install the No. 4 instrument panel register assembly.



Hide 55660 22.INSTALL NO. 2 INSTRUMENT PANEL REGISTER ASSEMBLY

B432537

a.

Attach the 4 claws to install the No. 2 instrument panel register assembly.


Hide 55433B 23.INSTALL LOWER NO. 2 INSTRUMENT PANEL FINISH PANEL

B432510

a.

Connect the connector.


b.

Attach the 3 claws to install the lower No. 2 instrument panel finish panel.


c.
U156003E01
0.747,1.018 0.939,1.197 0.192,0.179 10 *a 2.609,1.018 2.801,1.197 0.192,0.179 10 *a 0.598,1.791 0.790,1.970 0.192,0.179 10 *a 2.529,1.877 2.721,2.056 0.192,0.179 10 *a

Install the 4 screws <C>.

Text in Illustration
*a Screw <C>


Hide 55443D 24.INSTALL INSTRUMENT PANEL BOX DOOR KNOB

HINT:

Use the same procedure for both instrument panel box door knobs.


a.
B182549

Attach the 2 claws to install the instrument panel box door knob.


Hide 55476A 25.INSTALL NO. 3 INSTRUMENT CLUSTER FINISH PANEL GARNISH

B432539

a.

Attach the 6 claws to install the No. 3 instrument cluster finish panel garnish.


Hide 55312 26.INSTALL LOWER INSTRUMENT PANEL (w/o Passenger Side Knee Airbag)

U163957E01
0.5,1.555 0.692,1.734 0.192,0.179 10 *a 2.475,1.852 2.666,2.031 0.192,0.179 10 *a

a.

Attach the 4 claws to install the lower instrument panel.


b.

Install the 2 bolts <B>.

Text in Illustration
*a Bolt <B>


Hide 73990 27.INSTALL LOWER NO. 2 INSTRUMENT PANEL AIRBAG ASSEMBLY (w/ Passenger Side Knee Airbag)

Hide 62111C 28.INSTALL COWL SIDE TRIM BOARD RH

U155994E01
0.696,0.961 0.888,1.140 0.192,0.179 10 *a

a.

Attach the 2 clips to install the cowl side trim board RH.


b.

Install the cap nut.

Text in Illustration
*a Cap Nut


Hide 55607 29.INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (w/ Floor Under Cover)

B432506

a.

Connect the connector.


b.

Attach the 3 guides.


c.

Attach the 4 claws to install the No. 2 instrument panel under cover sub-assembly.


Hide 55317A 31.INSTALL INSTRUMENT SIDE PANEL RH

B432540

a.

w/ Airbag Cut Off Switch:

i.

Connect the connector.



b.

Attach the 6 claws to install the instrument side panel RH.


Hide 55650 32.INSTALL NO. 1 INSTRUMENT PANEL REGISTER ASSEMBLY

B432541

a.

Attach the 4 claws to install the No. 1 instrument panel register assembly.


Hide 55303B 33.INSTALL LOWER INSTRUMENT PANEL SUB-ASSEMBLY (w/o Driver Side Knee Airbag)

U163956E01
0.799,1.869 0.990,2.048 0.192,0.179 10 *a 1.796,1.606 1.988,1.785 0.192,0.179 10 *a 2.667,1.034 2.859,1.213 0.192,0.179 10 *a 2.872,0.618 3.064,0.797 0.192,0.179 10 *a 1.584,0.868 1.775,1.047 0.192,0.179 10 *a

a.

Attach the 2 claws and connect the DLC3.


b.

Install the lower instrument panel sub-assembly with the 5 bolts.

Text in Illustration
*a Bolt <B>


Hide 73900 34.INSTALL LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY (w/ Driver Side Knee Airbag)

Hide 55446A 35.INSTALL NO. 1 SWITCH HOLE BASE

B432542

a.

Connect the connectors.


b.

Attach the 4 claws to install the No. 1 switch hole base.


Hide 55432D 36.INSTALL LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL

a.

Connect the connectors.


b.
B181942

Attach the 2 claws to connect the 2 control cables.


c.

for Automatic Air Conditioning System:

i.
B180296

Attach the 2 claws to install the room temperature sensor.



d.

w/ Driver Side Knee Airbag:

i.

Attach the 16 claws to install the lower No. 1 instrument panel finish panel.

B434077



e.

w/o Driver Side Knee Airbag:

i.

Attach the 9 claws to install the lower No. 1 instrument panel finish panel.

B434078



f.
U156004E01
1.191,1.715 1.383,1.894 0.192,0.179 10 *a 3.075,1.622 3.267,1.801 0.192,0.179 10 *a

Install the 2 bolts <B>.

Text in Illustration
*a Bolt <B>


g.
B182569

Attach the 2 claws to close the hole cover.


Hide 62112 37.INSTALL COWL SIDE TRIM BOARD LH

U155989E01
2.437,0.892 2.629,1.071 0.192,0.179 10 *a

a.

Attach the 2 clips to install the cowl side trim board LH.


b.

Install the cap nut.

Text in Illustration
*a Cap Nut


Hide 55606 38.INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (w/ Floor Under Cover)

U155808E01
2.024,0.184 2.215,0.363 0.192,0.179 10 *a 2.879,0.369 3.071,0.548 0.192,0.179 10 *a

a.

Connect the connector.


b.

Attach the 3 claws to install the No. 1 instrument panel under cover sub-assembly.


c.

Install the 2 screws <A>.

Text in Illustration
*a Screw <A>


Hide 83100 40.INSTALL COMBINATION METER ASSEMBLY

B432499

a.

Connect the connectors.


b.

Install the combination meter assembly with the 4 screws.


Hide 55404C 41.INSTALL NO. 2 INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY

B432544

a.

Connect the connector.


b.

Attach the 9 claws to install the No. 2 instrument cluster finish panel sub-assembly.


Hide 55475A 42.INSTALL NO. 2 INSTRUMENT CLUSTER FINISH PANEL GARNISH

B432545

a.

Attach the 2 claws to install the No. 2 instrument cluster finish panel garnish.


Hide 55474C 43.INSTALL NO. 1 INSTRUMENT CLUSTER FINISH PANEL GARNISH

B432546

a.

Attach the 3 claws to install the No. 1 instrument cluster finish panel garnish.


Hide 55318C 44.INSTALL INSTRUMENT SIDE PANEL LH

B432547

a.

Attach the 6 claws to install the instrument side panel LH.


Hide 58901A 45.INSTALL REAR CONSOLE BOX SUB-ASSEMBLY (w/o Cool Box)

Hide 88520 46.INSTALL COOLING BOX ASSEMBLY (w/ Cool Box)

Hide 58812A 47.INSTALL LOWER CONSOLE BOX (w/o Console Box Lid)

Hide 84140 48.INSTALL HEADLIGHT DIMMER SWITCH ASSEMBLY

Hide 49.INSTALL FRONT SEAT ASSEMBLY LH

Hide 51.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 54.CHECK FOR REFRIGERANT GAS LEAK (w/ Cool Box)

Hide 55.ENABLE AUTOAWAY/RETURN FUNCTION (for Power Tilt and Power Telescopic Steering Column)

a.

Restore the autoaway/return function setting to the previous condition by changing the customize parameter (See page Steering>STEERING COLUMN>POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM>CUSTOMIZE PARAMETERS).