Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM › from 2015.08
RM2660E _57 Power Source / Network _052837 NETWORKING _0255535 LIN COMMUNICATION SYSTEM C

NETWORKING  LIN COMMUNICATION SYSTEM  B2325  LIN Communication Bus Malfunction  


DESCRIPTION

The main body ECU (multiplex network body ECU) intermittently monitors the LIN communication bus between the components related to the door and sliding roof. DTC B2325 is stored when a malfunction in the LIN communication bus between the components related to the door and sliding roof is detected consecutively 3 times.

DTC Code DTC Detection Condition Trouble Area
B2325 The main body ECU (multiplex network body ECU) detects a malfunction in the LIN communication bus between components related to the doors and sliding roof consecutively 3 times.
for LHD:
·

Multiplex network master switch assembly

·

Front power window regulator motor LH

·

Front power window regulator motor RH*1

·

Rear power window regulator motor LH*1

·

Rear power window regulator motor RH*1

·

Sliding roof driver gear sub-assembly (Sliding roof ECU)*2

·

Double lock door control relay*3

·

Main body ECU (multiplex network body ECU)

·

Harness or connector


for RHD:
·

Multiplex network master switch assembly

·

Front power window regulator motor RH

·

Front power window regulator motor LH*1

·

Rear power window regulator motor RH*1

·

Rear power window regulator motor LH*1

·

Sliding roof driver gear sub-assembly (Sliding roof ECU)*2

·

Double lock door control relay assembly*3

·

Main body ECU (multiplex network body ECU)

·

Harness or connector



*1: for Models with Jam Protection Function on 4 Windows

*2: w/ Sliding Roof System

*3: w/ Double Locking System


WIRING DIAGRAM

E326597E04
4.95,1.494 5.160,1.676 0.210,0.181 10 I11 1.303,4.234 1.637,4.415 0.334,0.181 10 R18 5.172,3.505 5.382,3.686 0.210,0.181 10 I12 4.95,1.67 6.562,1.997 1.611,0.327 10 Multiplex Network Master Switch Assembly 1.303,4.374 2.752,4.555 1.449,0.181 10 Sliding Roof ECU*1 1.106,5.614 1.262,5.795 0.156,0.181 10 I4 5.079,0.703 5.389,0.884 0.310,0.181 10 LIN1 1.24,0.718 1.550,0.900 0.310,0.181 10 LIN2 0.18,0.078 1.366,0.408 1.186,0.329 12 for LHD: 5.079,1.053 5.389,1.234 0.310,0.181 10 LIN2 5.079,3.064 5.312,3.245 0.233,0.181 10 LIN 2.104,5.146 2.337,5.327 0.233,0.181 10 LIN 2.104,6.68 2.337,6.861 0.233,0.181 10 LIN 5.009,6.68 5.242,6.861 0.233,0.181 10 LIN 4.75,6.503 4.906,6.684 0.156,0.181 10 9 5.009,5.167 5.409,5.348 0.400,0.181 10 MPX1 4.757,0.549 4.928,0.730 0.171,0.181 10 17 2.858,0.549 3.030,0.730 0.171,0.181 10 13 1.639,0.549 1.811,0.730 0.171,0.181 10 16 4.757,0.906 4.928,1.087 0.171,0.181 10 16 4.792,2.91 4.948,3.091 0.156,0.181 10 9 2.466,3.568 2.637,3.749 0.171,0.181 10 11 2.435,4.997 2.591,5.178 0.156,0.181 10 9 2.435,6.503 2.591,6.684 0.156,0.181 10 9 4.75,4.99 4.906,5.171 0.156,0.181 10 9 1.94,3.757 2.336,3.938 0.395,0.181 10 MPX1 5.172,3.68 6.607,4.109 1.435,0.429 10 Front Power Window Regulator Motor LH 1.037,7.148 1.278,7.329 0.241,0.181 10 J11 1.037,7.288 3.769,7.674 2.732,0.386 10 Rear Power Window Regulator Motor LH*2 0.389,7.949 4.107,8.092 3.718,0.143 10 *2: for Models with Jam Protection Function on 4 Windows 0.389,8.242 2.447,8.385 2.059,0.143 10 *3: w/ Double Locking System 0.743,8.528 2.885,8.695 2.142,0.167 10 : LIN Communication Line 1.106,5.768 3.102,6.105 1.996,0.338 10 Front Power Window Regulator Motor RH*2 4.21,7.148 4.374,7.329 0.164,0.181 10 J4 4.21,7.288 6.949,7.674 2.739,0.386 10 Rear Power Window Regulator Motor RH*2 4.077,5.663 4.532,5.844 0.455,0.181 10 E167 4.077,5.803 6.934,6.022 2.857,0.220 10 Double Lock Door Control Relay Assembly*3 1.669,1.677 1.833,1.858 0.164,0.181 10 2J 1.669,1.835 3.503,2.058 1.834,0.223 10 Cowl Side Junction Block LH 0.416,2.522 2.082,2.930 1.666,0.408 10 Main Body ECU (Multiplex Network Body ECU) 0.427,2.363 0.591,2.544 0.164,0.181 10 A 0.389,7.657 2.628,7.799 2.239,0.142 10 *1: w/ Sliding Roof System

E326597E03
4.992,1.459 5.202,1.641 0.210,0.181 10 I22 1.303,4.234 1.575,4.415 0.272,0.181 10 R18 5.172,3.505 5.382,3.686 0.210,0.181 10 I4 4.992,1.6 6.590,1.996 1.597,0.397 10 Multiolex Network Master Switch Assembly 1.303,4.374 2.752,4.555 1.449,0.181 10 Sliding Roof ECU*1 1.151,5.635 1.451,5.816 0.299,0.181 10 I12 5.079,0.703 5.389,0.884 0.310,0.181 10 LIN1 1.24,0.718 1.550,0.900 0.310,0.181 10 LIN2 0.18,0.078 1.366,0.408 1.186,0.329 12 for RHD: 5.079,1.053 5.389,1.234 0.310,0.181 10 LIN2 5.079,3.064 5.312,3.245 0.233,0.181 10 LIN 2.104,5.146 2.337,5.327 0.233,0.181 10 LIN 2.104,6.68 2.337,6.861 0.233,0.181 10 LIN 5.009,6.68 5.242,6.861 0.233,0.181 10 LIN 4.75,6.503 4.906,6.684 0.156,0.181 10 9 5.009,5.167 5.409,5.348 0.400,0.181 10 MPX1 4.757,0.549 4.928,0.730 0.171,0.181 10 17 2.858,0.549 3.030,0.730 0.171,0.181 10 13 1.639,0.549 1.811,0.730 0.171,0.181 10 16 4.757,0.906 4.928,1.087 0.171,0.181 10 16 4.792,2.91 4.948,3.091 0.156,0.181 10 9 2.466,3.568 2.637,3.749 0.171,0.181 10 11 2.435,4.997 2.591,5.178 0.156,0.181 10 9 2.435,6.503 2.591,6.684 0.156,0.181 10 9 4.75,4.99 4.906,5.171 0.156,0.181 10 9 1.94,3.757 2.336,3.938 0.395,0.181 10 MPX1 5.172,3.68 6.607,4.109 1.435,0.429 10 Front Power Window Regulator Motor RH 1.037,7.148 1.278,7.329 0.241,0.181 10 J11 1.037,7.288 3.769,7.674 2.732,0.386 10 Rear Power Window Regulator Motor LH*2 0.389,7.949 4.107,8.092 3.718,0.143 10 *2: for Models with Jam Protection Function on 4 Windows 0.389,8.242 2.447,8.385 2.059,0.143 10 *3: w/ Double Locking System 0.743,8.528 2.885,8.695 2.142,0.167 10 : LIN Communication Line 1.151,5.789 3.182,6.126 2.031,0.338 10 Front Power Window Regulator Motor LH*2 4.21,7.148 4.374,7.329 0.164,0.181 10 J4 4.21,7.288 6.949,7.674 2.739,0.386 10 Rear Power Window Regulator Motor RH*2 4.035,5.663 4.490,5.844 0.455,0.181 10 E167 4.035,5.803 6.885,5.987 2.850,0.185 10 Double Lock Door Control Relay Assembly*3 1.669,1.677 1.833,1.858 0.164,0.181 10 2J 1.669,1.835 3.503,2.058 1.834,0.223 10 Cowl Side Junction Block LH 0.416,2.522 2.082,2.930 1.666,0.408 10 Main Body ECU (Multiplex Network Body ECU) 0.427,2.363 0.591,2.544 0.164,0.181 10 A 0.389,7.657 2.628,7.799 2.239,0.142 10 *1: w/ Sliding Roof System

CAUTION / NOTICE / HINT

NOTICE:

When using the GTS with the ignition switch off to troubleshoot:

Connect the GTS to the vehicle, and turn a courtesy switch on and off at 1.5 second intervals until communication between the GTS and vehicle begins.


HINT:

When DTC B2325 and a LIN communication stop DTC are output simultaneously, first perform the troubleshooting for the LIN communication stop DTC. Then perform the troubleshooting for DTC B2325.


PROCEDURE

1.CLEAR DTC

NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Recheck for DTCs (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B2325 is output A
DTC B2325 is not output B



A

3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - MASTER SWITCH)

B

3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - MASTER SWITCH)

*1: w/ Sliding Roof System

*2: for Models with Jam Protection Function on 4 Windows

*3: w/ Double Locking System


a.

for LHD:

i.

Disconnect the A main body ECU connector.


ii.

Disconnect the R18 sliding roof ECU connector*1.


iii.

Disconnect the I12 power window regulator motor connector.


iv.

Disconnect the I4, J4 and J11 power window regulator motor connectors*2.


v.

Disconnect the I11 master switch connector.


vi.

Disconnect the E167 double lock door control relay connector*3.


vii.

Measure the resistance according to the value(s) in the tables below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-16 (LIN2) - I11-17 (LIN1) Always Below 1 Ω
A-16 (LIN2) - Body ground Always 10 kΩ or higher




b.

for RHD:

i.

Disconnect the A main body ECU connector.


ii.

Disconnect the R18 sliding roof ECU connector*1.


iii.

Disconnect the I4 power window regulator motor connector.


iv.

Disconnect the I12, J4 and J11 power window regulator motor connectors*2.


v.

Disconnect the I22 master switch connector.


vi.

Disconnect the E167 double lock door control relay connector*3.


vii.

Measure the resistance according to the value(s) in the tables below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-16 (LIN2) - I22-17 (LIN1) Always Below 1 Ω
A-16 (LIN2) - Body ground Always 10 kΩ or higher





OK

4.CLEAR DTC

NG

18.CHECK HARNESS AND CONNECTOR (COWL SIDE JUNCTION BLOCK LH - MASTER SWITCH)
4.CLEAR DTC

*1: w/ Sliding Roof System

*2: for Models with Jam Protection Function on 4 Windows

*3: w/ Double Locking System


a.

for LHD:

i.

Reconnect the A main body ECU connector.


ii.

Reconnect the R18 sliding roof ECU connector*1.


iii.

Reconnect the I12 power window regulator motor connector.


iv.

Reconnect the I4, J4 and J11 power window regulator motor connectors*2.


v.

Disconnect the I11 master switch connector.


vi.

Reconnect the E167 double lock door control relay connector*3.



b.

for RHD:

i.

Reconnect the A main body ECU connector.


ii.

Reconnect the R18 sliding roof ECU connector*1.


iii.

Reconnect the I4 power window regulator motor connector.


iv.

Reconnect the I12, J4 and J11 power window regulator motor connectors*2.


v.

Disconnect the I22 master switch connector.


vi.

Reconnect the E167 double lock door control relay connector*3.





NEXT

5.CHECK FOR DTC
5.CHECK FOR DTC
a.

Recheck for DTCs (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B2325 is output A
DTC B2325 is not output B



A

6.CLEAR DTC

B

6.CLEAR DTC
a.

for LHD:

i.

Reconnect the I11 master switch connector.


ii.

Disconnect the I12 power window regulator motor connector.



b.

for LHD:

i.

Reconnect the I22 master switch connector.


ii.

Disconnect the I4 power window regulator motor connector.





NEXT

7.CHECK FOR DTC
7.CHECK FOR DTC
a.

Recheck for DTCs (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B2325 is output A
DTC B2325 is not output (for LHD) B
DTC B2325 is not output (for RHD) C



A

8.CLEAR DTC

B

REPLACE FRONT POWER WINDOW REGULATOR MOTOR LH

C

REPLACE FRONT POWER WINDOW REGULATOR MOTOR RH

8.CLEAR DTC

*: for Models with Jam Protection Function on 4 Windows


a.

for LHD:

i.

Reconnect the I12 power window regulator motor connector.


ii.

Disconnect the I4 power window regulator motor connector*.



b.

for LHD:

i.

Reconnect the I4 power window regulator motor connector.


ii.

Disconnect the I12 power window regulator motor connector*.





NEXT

9.CHECK FOR DTC
9.CHECK FOR DTC
a.

Recheck for DTCs (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B2325 is output A
DTC B2325 is not output (for LHD) B
DTC B2325 is not output (for RHD) C



A

10.CLEAR DTC

B

REPLACE FRONT POWER WINDOW REGULATOR MOTOR RH

C

REPLACE FRONT POWER WINDOW REGULATOR MOTOR LH

10.CLEAR DTC

*: for Models with Jam Protection Function on 4 Windows


a.

for LHD:

i.

Reconnect the I4 power window regulator motor connector*.


ii.

Disconnect the J4 power window regulator motor connector*.



b.

for LHD:

i.

Reconnect the I12 power window regulator motor connector*.


ii.

Disconnect the J4 power window regulator motor connector*.





NEXT

11.CHECK FOR DTC
11.CHECK FOR DTC
a.

Recheck for DTCs (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B2325 is output A
DTC B2325 is not output B



A

12.CLEAR DTC

B

REPLACE REAR POWER WINDOW REGULATOR MOTOR RH

12.CLEAR DTC

*: for Models with Jam Protection Function on 4 Windows


a.

Reconnect the J4 power window regulator motor connector*.


b.

Disconnect the J11 power window regulator motor connector*.




NEXT

13.CHECK FOR DTC
13.CHECK FOR DTC
a.

Recheck for DTCs (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B2325 is output A
DTC B2325 is not output B



A

14.CLEAR DTC

B

REPLACE REAR POWER WINDOW REGULATOR MOTOR LH

14.CLEAR DTC

*1: for Models with Jam Protection Function on 4 Windows

*2: w/ Double Locking System


a.

Reconnect the J11 power window regulator motor connector*1.


b.

Disconnect the E167 double lock door control relay connector*2.




NEXT

15.CHECK FOR DTC
15.CHECK FOR DTC
a.

Recheck for DTC (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B2325 is output A
DTC B2325 is not output (for LHD) B
DTC B2325 is not output (for RHD) C



A

16.CLEAR DTC

B

REPLACE DOUBLE LOCK DOOR CONTROL RELAY

C

REPLACE DOUBLE LOCK DOOR CONTROL RELAY

16.CLEAR DTC

*1: w/ Double Locking System

*2: w/ Sliding Roof System


a.

Reconnect the J11 power window regulator motor connector*1.


b.

Disconnect the R18 sliding roof ECU connector*2.




NEXT

17.CHECK FOR DTC
17.CHECK FOR DTC
a.

Recheck for DTCs (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B2325 is output (for LHD) A
DTC B2325 is output (for RHD) B
DTC B2325 is not output C



A

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

B

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

C

REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY

18.CHECK HARNESS AND CONNECTOR (COWL SIDE JUNCTION BLOCK LH - MASTER SWITCH)

*1: w/ Sliding Roof System

*2: for Models with Jam Protection Function on 4 Windows

*3: w/ Double Locking System


a.

for LHD:

i.

Disconnect the 2J cowl side junction block LH connector.


ii.

Disconnect the R18 sliding roof ECU connector*1.


iii.

Disconnect the I12 power window regulator motor connector.


iv.

Disconnect the I4, J4 and J11 power window regulator motor connectors*2.


v.

Disconnect the I11 master switch connector.


vi.

Disconnect the E167 double lock door control relay connector*3.


vii.

Measure the resistance according to the value(s) in the tables below.

Standard Resistance:
Tester Connection Condition Specified Condition
2J-13 - I11-17 (LIN1) Always Below 1 Ω
2J-13 - Body ground Always 10 kΩ or higher




b.

for RHD:

i.

Disconnect the 2J cowl side junction block LH connector.


ii.

Disconnect the R18 sliding roof ECU connector*1.


iii.

Disconnect the I4 power window regulator motor connector.


iv.

Disconnect the I12, J4 and J11 power window regulator motor connectors*2.


v.

Disconnect the I22 master switch connector.


vi.

Disconnect the E167 double lock door control relay connector*3.


vii.

Measure the resistance according to the value(s) in the tables below.

Standard Resistance:
Tester Connection Condition Specified Condition
2J-13 - I22-17 (LIN1) Always Below 1 Ω
2J-13 - Body ground Always 10 kΩ or higher




Result
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C


A

B

C

REPAIR OR REPLACE HARNESS OR CONNECTOR