The door control receiver receives signals from the transmitter and sends these signals to the main body ECU. The main body ECU then controls all the doors by sending lock/unlock signals to each door.
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
When replacing the door control receiver, refer to the registration procedures (See page Vehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM(w/o Entry and Start System)>REGISTRATION).
Check the power door lock operation (See page Vehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK).
Each door locks and unlocks normally.
OK
NG
(See pageVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING)
Check the key reminder warning buzzer operation (See page Vehicle Interior>DOOR LOCK>KEY REMINDER WARNING SYSTEM>OPERATION CHECK).
If the key reminder warning buzzer is functioning normally, it can be assumed that the unlock warning switch is also functioning normally.
Key reminder warning buzzer operates normally.
OK
NG
(See pageVehicle Interior>DOOR LOCK>KEY REMINDER WARNING SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING)
Check whether the wireless door lock control functions operate normally with another registered transmitter.
Wireless door lock control functions operate normally.
OK
NG
Remove the battery from the inoperative wireless door control transmitter (See page Vehicle Interior>DOOR LOCK>TRANSMITTER BATTERY(w/o Entry and Start System)>REPLACEMENT).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Battery positive (+) - Battery negative (-) | Always | 2.5 to 3.2 V |
OK
NG
Move the transmitter in the vicinity of the door control receiver.
Refer to Parts Location for the location of the door control receiver (See page Vehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM(w/o Entry and Start System)>PARTS LOCATION).
Press and hold either the lock or unlock transmitter switch for 1 second, and check that the doors are locked or unlocked accordingly.
Wireless door lock control functions operate normally.
Check if electrical noise is the cause by moving the door control transmitter closer to the door control receiver. Moving closer will decrease the effects of electrical noise.
If the operation check can be performed normally, there is a high probability that electrical noise or a decrease in output from the door control transmitter is the cause of the malfunction. There is a high probability that electrical noise is the cause if the problem occurs only in a certain location or only during a certain time of day. Also, custom components may be causing electrical noise. If custom components are installed in the vehicle, remove them and perform the operation check again.
OK
NG
Disconnect the L47 receiver connector.
Disconnect the E118 main body ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L47-2 (RDA) - E118-4 (RDA) | Always | Below 1 Ω |
| L47-3 (PRG) - E118-5 (PRG) | Always | Below 1 Ω |
| L47-2 (RDA) - Body ground | Always | 10 kΩ or higher |
| L47-3 (PRG) - Body ground | Always | 10 kΩ or higher |
OK
NG
Disconnect the L47 receiver connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L47-1 (GND) - Body ground | Always | Below 1 Ω |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L47-5 (+B) - Body ground | Always | 11 to 14 V |
| *a | Front view of wire harness connector
(to Door Control Receiver) |
OK
NG
Using an oscilloscope, check the waveform.
| Item | Content |
|---|---|
| Tester Connection | L47-2 (RDA) - Body ground |
| Tool Setting | 10 V/DIV., 50 μs/DIV. |
| Condition | No key in ignition key cylinder, all doors closed and transmitter switch off → on |
Waveform is output normally (refer to illustration).
| Result | Proceed to |
|---|---|
| OK (for LHD) | A |
| OK (for RHD) | B |
| NG | C |
A
B
C