CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) AND COWL SIDE JUNCTION BLOCK LH
| *1 | Main Body ECU (Multiplex Network Body ECU) | - | - |
Remove the main body ECU (multiplex network body ECU) from the cowl side junction block LH.
Connect the cowl side junction block LH connectors.
Measure the voltage and resistance according to the value(s) in the table below.
| Tester Connection | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| A-11 (GND1) - Body ground | None - Body ground | Ground | Always | Below 1 Ω |
| A-30 (ACC) - Body ground | None - Body ground | ACC power supply | Engine switch on (ACC) | 11 to 14 V |
| Engine switch off | Below 1 V | |||
| A-31 (BECU) - Body ground | None - Body ground | Battery power supply | Always | 11 to 14 V |
| A-32 (IG) - Body ground | None - Body ground | IG power supply | Engine switch on (IG) | 11 to 14 V |
| Engine switch off | Below 1 V | |||
| E118-6 (FLCY) - Body ground | V - Body ground | Front door courtesy light switch assembly LH input signal | Front door LH closed (OFF) → open (ON) | 10 kΩ or higher → Below 1 Ω |
| E118-27 (FRCY) - Body ground | V - Body ground | Front door courtesy light switch assembly RH input signal | Front door RH closed (OFF) → open (ON) | 10 kΩ or higher → Below 1 Ω |
| A-13 (LCTY) - Body ground | None - Body ground | Rear door courtesy light switch assembly LH input signal | Rear door LH closed (OFF) → open (ON) | 10 kΩ or higher → Below 1 Ω |
| A-2 (RCTY) - Body ground | None - Body ground | Rear door courtesy light switch assembly RH input signal | Rear door RH closed (OFF) → open (ON) | 10 kΩ or higher → Below 1 Ω |
| A-4 (BCTY) - Body ground | None - Body ground | Back door courtesy light switch signal | Back door closed (OFF) → open (ON) | 10 kΩ or higher → Below 1 Ω |
| E118-11 (HCTY) - Body ground | L - Body ground | Engine hood courtesy switch input signal | Engine hood open (OFF) → closed (ON) | 10 kΩ or higher → Below 1 Ω |
Install the main body ECU (multiplex network body ECU) to the cowl side junction block LH.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| 2J-19 (LSFL) - Body ground | G - Body ground | Front door LH unlock detection switch input signal | Front door LH unlocked | Below 1 V |
| Engine switch off, all doors closed and front door LH locked | Pulse generation | |||
| 2J-16 (LSFR) - Body ground | B - Body ground | Front door RH unlock detection switch input signal | Front door RH unlocked | Below 1 V |
| Engine switch off, all doors closed and front door RH locked | Pulse generation | |||
| 2K-33 (LSWL) - Body ground | L - Body ground | Rear door LH unlock detection switch input signal | Rear door LH unlocked | Below 1 V |
| Engine switch off, all doors closed and rear door LH locked | Pulse generation | |||
| E117-2 (LSWR) - Body ground | W - Body ground | Rear door RH unlock detection switch input signal | Rear door RH unlocked | Below 1 V |
| Engine switch off, all doors closed and rear door RH locked | Pulse generation | |||
| 2H-26 (SH) - Body ground*4 | LG - Body ground | Security horn drive | Security horn sounding
(Theft deterrent system is in alarm sounding state) |
Pulse generation
(Below 1 V ← → 11 to 14 V) |
| E117-18 (SSCL) - Body ground*1 | R - Body ground | Theft warning siren drive | Theft warning siren sounding
(Theft deterrent system is in alarm sounding state) |
Pulse generation
(Below 1 V ← → 11 to 14 V) |
| E117-13 (SSW1) - Body ground*2 | L - Body ground | Intrusion sensor cancel switch signal | Intrusion sensor cancel switch on | Below 1 V |
| Intrusion sensor cancel switch off | Pulse generation | |||
| E117-12 (ISIF) - Body ground*2 | G - Body ground | Intrusion sensor (theft warning ultrasonic sensor) signal input | No moving object detected by sensor | 11 to 14 V |
| Moving object detected by sensor during arming preparation state or armed state | Pulse generation | |||
| E117-6 (GCS) - Body ground*4 | B - Body ground | Communication line between main body ECU (multiplex network body ECU) and tilt sensor | ·
Theft deterrent system changes from armed preparation state to armed state. ·
The tilt sensor detects pitch angle of vehicle inclination when theft deterrent system is in armed state. |
Pulse generation |
| E118-7 (GPBS) - Body ground*3 | V - Body ground | Glass breakage sensor signal | Glass breakage sensor normal | Below 2 V |
| 2H-27 (HORN) - Body ground | L - Body ground | Vehicle horn drive | Vehicle horns sounding
(Theft deterrent system is in alarm sounding state) |
Pulse generation
(Below 1 V ← → 11 to 14 V) |
*1: w/ Theft Warning Siren Assembly
*2: w/ Intrusion Sensor
*3: w/ Glass Breakage Sensor
*4: w/ Security Horn Assembly