Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM (w/ Entry and Start System) › from 2015.08
RM2660E _58 Vehicle Interior _052839 THEFT DETERRENT / KEYLESS ENTRY _0255573 ENGINE IMMOBILISER SYSTEM(w/ Entry and Start System) J

THEFT DETERRENT / KEYLESS ENTRY  ENGINE IMMOBILISER SYSTEM(w/ Entry and Start System)  Security Indicator Light Does not Blink  


DESCRIPTION

·

The certification ECU (smart key ECU assembly) blinks the security indicator light when the immobiliser is set (engine switch off, or driver door is opened and closed with engine switch on [IG]).

·

The certification ECU (smart key ECU assembly) receives the security indicator light signal from the main body ECU (multiplex network body ECU) via CAN communication when the theft deterrent system is in the arming preparation state or alarm sounding state. Then, the certification ECU (smart key ECU assembly) blinks the security indicator light.


WIRING DIAGRAM

(w/ Multi-media Module Receiver Assembly)


B374004E08
0.792,1.469 2.396,2.01 1.604,0.542 10 false Security Indicator Light (Multi-media Module Receiver Assembly) 0.802,1.313 1.24,1.51 0.438,0.198 10 false F77 2.219,0.74 2.708,0.917 0.49,0.177 10 false 37 0.594,0.729 0.802,0.906 0.208,0.177 10 false 12 1.729,0.865 2.177,1.052 0.448,0.188 10 false SEUC 3.188,0.854 3.573,1.031 0.385,0.177 10 false IND 2.927,0.74 3.313,0.917 0.385,0.177 10 false 19 3.083,1.49 4.625,1.906 1.542,0.417 10 false Certification ECU (Smart Key ECU Assembly) 3.094,1.333 3.802,1.552 0.708,0.219 10 false E130 5.365,1.323 7.021,1.688 1.656,0.365 10 false Main Body ECU (Multiplex Network Body ECU) 0.583,2.427 2.427,2.667 1.844,0.24 10 false : CAN Communication Line 0.854,0.854 1.521,1.094 0.667,0.24 10 false GND1

(w/o Multi-media Module Receiver Assembly)


B374004E09
0.781,1.479 2.656,1.969 1.875,0.49 10 false Security Indicator Light (Clock Assembly) 0.802,1.292 1.323,1.5 0.521,0.208 10 false g1 2.219,0.771 2.708,0.948 0.49,0.177 10 false 9 0.698,0.76 0.938,0.979 0.24,0.219 10 false 1 1.896,0.771 2.135,0.969 0.24,0.198 10 false LP 3.188,0.854 3.573,1.031 0.385,0.177 10 false IND 2.917,0.771 3.302,0.948 0.385,0.177 10 false 19 3.083,1.469 4.667,1.865 1.583,0.396 10 false Certification ECU (Smart Key ECU Assembly) 3.083,1.323 3.792,1.542 0.708,0.219 10 false E130 5.302,1.313 7.042,1.906 1.74,0.594 10 false Main Body ECU (Multiplex Network Body ECU) 0.594,2.438 2.688,2.688 2.094,0.25 10 false : CAN Communication Line 0.854,0.771 1.396,0.948 0.542,0.177 10 false E

CAUTION / NOTICE / HINT

NOTICE:
·

The engine immobiliser system uses the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the engine immobiliser system after confirming that the communication systems are functioning properly (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM (w/ Entry and Start System)>HOW TO PROCEED WITH TROUBLESHOOTING).

·

When using the GTS with the engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

Before replacing the certification ECU (smart key ECU assembly) or main body ECU (multiplex network body ECU), refer to Service Bulletin.



PROCEDURE

1.CHECK FOR DTC

OK

2.PERFORM ACTIVE TEST USING GTS (IMMOBILISERINDICATOR)

NG

2.PERFORM ACTIVE TEST USING GTS (IMMOBILISERINDICATOR)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Entry&Start / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Entry&Start
Tester Display Test Part Control Range Diagnostic Note
Immobiliser Indicator Security indicator light OFF/ON -

OK:

The security indicator light operates normally.




OK

3.CHECK SECURITY INDICATOR LIGHT OPERATION

NG

4.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] - SECURITY INDICATOR LIGHT AND BODY GROUND)
3.CHECK SECURITY INDICATOR LIGHT OPERATION
a.

When the immobiliser is set, check that the security indicator light blinks*1.

OK:

The security indicator light blinks normally.



b.

When the theft deterrent system is in the arming preparation state, check that the security indicator light illuminates*2.

OK:

The security indicator light illuminates normally.


Result
Result Proceed to
*1 is NG (*2 is OK) A
*2 is NG (*1 is OK) (for LHD) B
*2 is NG (*1 is OK) (for RHD) C



A

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

B

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

C

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

4.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] - SECURITY INDICATOR LIGHT AND BODY GROUND)
a.

Disconnect the E130 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the F77*1 or g1*2 security indicator light connector.

·

*1: w/ Multi-media Module Receiver Assembly

·

*2: w/o Multi-media Module Receiver Assembly



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
(w/ Multi-media Module Receiver Assembly)
Tester Connection Condition Specified Condition
E130-19 (IND) - F77-37 (SEUC) Always Below 1 Ω
E130-19 (IND) or F77-37 (SEUC) - Body ground Always 10 kΩ or higher
F77-12 (GND1) - Body ground Always Below 1 Ω

(w/o Multi-media Module Receiver Assembly)
Tester Connection Condition Specified Condition
E130-19 (IND) - g1-9 (LP) Always Below 1 Ω
130-19 (IND) or g1-9 (LP) - Body ground Always 10 kΩ or higher
g1-1 (E) - Body ground Always Below 1 Ω




OK

5.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Connect the E130 certification ECU (smart key ECU assembly) connector.

U164317E01
4.445,1.85 4.832,2.008 0.387,0.158 10 IND 0.21,0.07 0.396,0.229 0.186,0.158 10 *a 5.181,0.238 5.654,0.461 0.473,0.223 10 E130 5.177,1.078 4.918,1.94 4.918,1.94 4.795,1.94 false 5.177,1.078 4.918,1.94 4.918,1.94 4.795,1.94 false

Text in Illustration
*a Component with harness connected
(Certification ECU [Smart Key ECU Assembly])
- -


b.

Connect the F77*1 or g1*2 security indicator light connector.

·

*1: w/ Multi-media Module Receiver Assembly

·

*2: w/o Multi-media Module Receiver Assembly



c.

Using an oscilloscope, check the waveform.

Measurement Condition:
Tester Connection Condition Specified Condition
E130-19 (IND) - Body ground Engine switch off → on (IG) Pulse generation → Below 2 V


Result
Result Proceed to
OK (w/ Multi-media Module Receiver Assembly) A
OK (w/o Multi-media Module Receiver Assembly) B
NG C



A

REPLACE MULTI-MEDIA MODULE RECEIVER ASSEMBLY (SECURITY INDICATOR LIGHT)

B

REPLACE CLOCK ASSEMBLY (SECURITY INDICATOR LIGHT)

C

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)