Home › Vehicle Interior › PRE-CRASH SAFETY › PRE-CRASH SAFETY SYSTEM › 2014.08–2015.08
RM2660E _58 Vehicle Interior _052844 PRE-CRASH SAFETY _0255621 PRE-CRASH SAFETY SYSTEM C

PRE-CRASH SAFETY  PRE-CRASH SAFETY SYSTEM  B2000  Short to B+ in Seat Belt Motor RH Circuit  B2005  Short to B+ in Seat Belt Motor LH Circuit  


DESCRIPTION

The seat belt control ECU receives information from the master cylinder solenoid (skid control ECU) via the CAN communication line and tightens the seat belt by operating the motor in the front seat outer belt assembly RH or LH.

DTC Code DTC Detection Condition Trouble Area
B2000
·

Short to B+ in the seat belt motor RH circuit continues for 1 second or more.

·

Short in the seat belt motor RH circuit.


·

Front seat outer belt assembly RH

·

Harness or connector

·

Seat belt control ECU


B2005
·

Short to B+ in the seat belt motor LH circuit continues for 1 second or more.

·

Short in the seat belt motor LH circuit.


·

Front seat outer belt assembly LH

·

Harness or connector

·

Seat belt control ECU



WIRING DIAGRAM

E149036E03
1.927,0.521 2.365,0.677 0.438,0.156 10 false MOR+ 0.083,0.073 0.792,0.292 0.708,0.219 12 false for RH: 1.927,1.323 2.365,1.479 0.438,0.156 10 false MOR- 4.865,1.396 5.313,1.552 0.448,0.156 10 false MOR- 4.802,1.99 5.25,2.146 0.448,0.156 10 false E41 4.865,0.604 5.313,0.76 0.448,0.156 10 false MOR+ 4.802,2.135 6.271,2.427 1.469,0.292 10 false Seat Belt Control ECU 0.948,1.979 1.396,2.135 0.448,0.156 10 false L5 0.948,2.115 3.188,2.531 2.24,0.417 10 false Front Seat Outer Belt Assembly RH (Seat Belt Motor RH) 2.438,0.521 2.563,0.677 0.125,0.156 10 false 1 2.438,1.313 2.563,1.469 0.125,0.156 10 false 2 4.615,0.521 4.74,0.677 0.125,0.156 10 false 2 4.615,1.313 4.74,1.469 0.125,0.156 10 false 1

E149036E04
1.927,0.521 2.365,0.677 0.438,0.156 10 false MOL+ 0.083,0.094 0.656,0.344 0.573,0.25 12 false for LH: 1.927,1.323 2.365,1.479 0.438,0.156 10 false MOL- 4.865,1.396 5.313,1.552 0.448,0.156 10 false MOL- 4.802,1.99 5.25,2.146 0.448,0.156 10 false E41 4.865,0.604 5.313,0.76 0.448,0.156 10 false MOL+ 4.802,2.135 6.271,2.427 1.469,0.292 10 false Seat Belt Control ECU 0.948,1.979 1.396,2.135 0.448,0.156 10 false K11 0.948,2.115 3.188,2.531 2.24,0.417 10 false Front Seat Outer Belt Assembly LH (Seat Belt Motor LH) 2.438,0.521 2.563,0.677 0.125,0.156 10 false 1 2.438,1.323 2.563,1.479 0.125,0.156 10 false 2 4.615,0.531 4.74,0.688 0.125,0.156 10 false 3 4.615,1.313 4.74,1.469 0.125,0.156 10 false 4

CAUTION / NOTICE / HINT

CAUTION:

The pretensioner is built into the front seat outer belt assembly. Be sure to follow the correct inspection procedure, as failure to follow the correct procedure (such as inspection of incorrect connectors) may deploy the pretensioner.


PROCEDURE

1.CHECK SEAT BELT CONTROL ECU
a.
U165821E02
2.198,1.635 2.521,1.01 true 0.875,1.01 1.354,1.646 true 2.323,1.792 2.469,2.583 true 1.208,1.781 1.354,2.573 true 1.615,0.917 2.063,1.073 0.448,0.156 10 false E41 2.281,2.688 2.802,2.854 0.521,0.167 10 false MOL-*1 0.083,2.688 0.729,2.854 0.646,0.167 10 false *1: for LH 0.083,3.042 0.729,3.208 0.646,0.167 10 false *2: for RH 2.583,0.906 3.135,1.073 0.552,0.167 10 false MOL+*1 0.177,0.906 0.74,1.073 0.563,0.167 10 false MOR+*2 1.125,2.688 1.698,2.854 0.573,0.167 10 false MOR-*2 0.292,0.094 2.656,0.656 2.365,0.563 10 false Front view of wire harness connector: (to Seat Belt Control ECU)

Disconnect the E41 seat belt control ECU connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for LH
Tester Connection Switch Condition Specified Condition
E41-3 (MOL+) - Body ground Ignition switch ON Below 1 V
E41-4 (MOL-) - Body ground

for RH
Tester Connection Switch Condition Specified Condition
E41-1 (MOR-) - Body ground Ignition switch ON Below 1 V
E41-2 (MOR+) - Body ground


Result
Result Proceed to
OK
(for LHD)
A
OK
(for RHD)
B
NG C



A

B

C

2.CHECK HARNESS AND CONNECTOR (FRONT SEAT OUTER BELT - SEAT BELT CONTROL ECU)
2.CHECK HARNESS AND CONNECTOR (FRONT SEAT OUTER BELT - SEAT BELT CONTROL ECU)
a.
U165817E02
1.5,2.365 1.198,2.802 true 1.969,2.365 2.49,2.802 true 0.333,0.094 2.719,0.677 2.385,0.583 10 false Front view of wire harness connector: (to Front Seat Outer Belt) 2.281,2.823 2.823,2.99 0.542,0.167 10 false MOL-*1 0.99,2.833 1.604,3 0.615,0.167 10 false MOL+*1 2.281,3.115 2.823,3.281 0.542,0.167 10 false MOR-*2 0.99,3.125 1.604,3.292 0.615,0.167 10 false MOR+*2 0.063,2.833 0.698,3 0.635,0.167 10 false *1: for LH 0.063,3.125 0.698,3.292 0.635,0.167 10 false *2: for RH 2.083,1.094 2.375,1.271 0.292,0.177 10 false L5 2.448,1.094 2.625,1.271 0.177,0.177 10 false *2 1.031,1.083 1.323,1.26 0.292,0.177 10 false K11 1.406,1.094 1.583,1.271 0.177,0.177 10 false *1

Disconnect the E41 seat belt control ECU connector.


b.

Disconnect the K11*1 or L5*2 front seat outer belt connector.

HINT:
·

*1: for LH

·

*2: for RH




c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage :
for LH
Tester Connection Switch Condition Specified Condition
K11-1 (MOL+) - Body ground Ignition switch ON Below 1 V
K11-2 (MOL-) - Body ground

for RH
Tester Connection Switch Condition Specified Condition
L5-1 (MOR+) - Body ground Ignition switch ON Below 1 V
L5-2 (MOR-) - Body ground


Result
Result Proceed to
OK
(for DTC B2000)
A
OK
(for DTC B2005)
B
NG C



A

REPLACE FRONT SEAT OUTER BELT ASSEMBLY RH

B

REPLACE FRONT SEAT OUTER BELT ASSEMBLY LH

C

REPAIR OR REPLACE HARNESS OR CONNECTOR