Home › Vehicle Interior › PRE-CRASH SAFETY › PRE-CRASH SAFETY SYSTEM › from 2015.08
RM2660E _58 Vehicle Interior _052844 PRE-CRASH SAFETY _0255621 PRE-CRASH SAFETY SYSTEM C

PRE-CRASH SAFETY  PRE-CRASH SAFETY SYSTEM  C1A4B  Stop Light Relay Circuit  


DESCRIPTION

The master cylinder solenoid (skid control ECU) sends a stop light operation request signal to the stop light relay (STP LP OPE). If the master cylinder solenoid (skid control ECU) detects a malfunction in the stop light relay circuit, the driving support ECU assembly stores DTC C1A4B.

Vehicle Condition
Pattern 1 Pattern 2
Diagnosis Condition IG1 terminal voltage is 11 to 14 V ○ ○
Stop Light illumination output (STPO) ON ○ -
Stop Light illumination output (STPO) OFF - ○
Malfunction Status No signal input to STP2 terminal ○ -
Signals input to STP and STP2 terminals do not match - ○
Malfunction Time 0.3 seconds or more 0.3 seconds or more
Number of Trips - -

DTC No. DTC Detection Condition Trouble Area
C1A4B Either of the following conditions is met:
·

When the engine switch is on (IG), the IG1 terminal voltage is between 11 and 14 V and the stop light illumination output signal (STPO) is output, the signal is not received at terminal STP2 for 0.3 seconds or more.

·

When the stop light illumination output (STPO) signal is off, signals input to the STP terminal and STP2 terminal of the master cylinder solenoid (skid control ECU) differ for 0.3 seconds or more continuously.


·

Lighting system

·

Stop light relay (STP LP OPE)

·

Master cylinder solenoid (Skid control ECU)

·

Harness or connector



WIRING DIAGRAM

E331221E14
1.115,1.094 3.635,1.333 2.521,0.24 10 false Driving Support ECU Assembly 0.375,2.031 1.188,2.219 0.813,0.188 10 false from Battery 0.25,1.573 1.396,1.75 1.146,0.177 10 false from IG Circuit 1.531,1.708 2.5,1.927 0.969,0.219 10 false ECU-IG NO. 1 1.771,2.219 2.25,2.438 0.479,0.219 10 false STOP 2.99,2.719 4.698,3.063 1.708,0.344 10 false Stop Light Relay (STP LP OPE) 3.115,1.417 3.323,1.625 0.208,0.208 10 false 1 3.104,1.906 3.313,2.115 0.208,0.208 10 false 5 3.104,2.229 3.313,2.438 0.208,0.208 10 false 4 4.406,1.417 4.615,1.625 0.208,0.208 10 false 2 4.417,2.063 4.625,2.271 0.208,0.208 10 false 3 5.51,1.458 5.771,1.646 0.26,0.188 10 false 16 5.51,2.094 5.771,2.281 0.26,0.188 10 false 45 5.823,1.438 6.281,1.625 0.458,0.188 10 false STPO 5.823,2.083 6.281,2.271 0.458,0.188 10 false STP2 5.823,3.49 6.281,3.677 0.458,0.188 10 false STP 5.573,3.458 5.781,3.667 0.208,0.208 10 false 7 3.104,3.5 4.271,3.885 1.167,0.385 10 false from Stop Light Switch Assembly 0.438,4.792 2.688,5.104 2.25,0.313 10 false Stop Light Control Relay Assembly 0.448,4.615 0.74,4.823 0.292,0.208 10 false A39 2.167,3.313 2.51,3.531 0.344,0.219 10 false OUT 0.906,3.313 1.177,3.479 0.271,0.167 10 false +B 0.677,3.26 0.885,3.469 0.208,0.208 10 false 6 2.594,3.26 2.802,3.469 0.208,0.208 10 false 8 0.667,4.104 0.875,4.313 0.208,0.208 10 false 4 2.167,4.115 2.625,4.302 0.458,0.188 10 false STP 0.917,4.104 1.292,4.313 0.375,0.208 10 false GND 5.344,4.219 5.677,4.427 0.333,0.208 10 false A24 5.323,4.406 6.948,5.031 1.625,0.625 10 false Master Cylinder Solenoid (Skid Control ECU) 4.323,4.646 4.781,4.833 0.458,0.188 10 false STP 3.375,4.656 3.708,4.906 0.333,0.25 10 false E 3.135,4.646 3.344,4.854 0.208,0.208 10 false 3 4.729,4.625 4.938,4.833 0.208,0.208 10 false 5 2.875,5.135 3.219,5.354 0.344,0.219 10 false L3 2.823,5.302 5.24,5.573 2.417,0.271 10 false Rear Combination Light Assembly RH 0.75,6.042 1.021,6.302 0.271,0.26 10 false K4 0.729,6.26 3.76,6.448 3.031,0.188 10 false Rear Combination Light Assembly LH 2.188,5.635 2.646,5.823 0.458,0.188 10 false STP 1.208,5.635 1.542,5.885 0.333,0.25 10 false E 2.583,5.604 2.792,5.813 0.208,0.208 10 false 5 0.948,5.625 1.156,5.833 0.208,0.208 10 false 3 1.292,7.74 3.26,7.969 1.969,0.229 10 false Center Stop Light Assembly 1.302,7.552 1.677,7.781 0.375,0.229 10 false S4 2.333,7.063 2.594,7.302 0.26,0.24 10 false B 1.708,7.073 2.042,7.323 0.333,0.25 10 false E 2.594,7.042 2.802,7.25 0.208,0.208 10 false 1 1.448,7.042 1.656,7.25 0.208,0.208 10 false 2 5.146,7.51 5.521,7.729 0.375,0.219 10 false S34 5.156,7.719 6.771,7.906 1.615,0.188 10 false Rear Light Assembly LH 5.302,6.031 5.635,6.26 0.333,0.229 10 false S35 5.292,6.24 6.917,6.51 1.625,0.271 10 false Rear Light Assembly RH 5.833,5.625 6.094,5.865 0.26,0.24 10 false B 6.479,5.625 6.813,5.875 0.333,0.25 10 false E 5.823,7.052 6.083,7.292 0.26,0.24 10 false B 6.458,7.042 6.792,7.292 0.333,0.25 10 false E 5.604,5.615 5.813,5.823 0.208,0.208 10 false 1 6.698,5.604 6.906,5.813 0.208,0.208 10 false 4 5.604,7.042 5.813,7.25 0.208,0.208 10 false 1 6.698,7.031 6.906,7.24 0.208,0.208 10 false 4 0.635,8.385 2.417,8.594 1.781,0.208 10 false : CAN Communication Line 2.594,4.042 2.792,4.292 0.198,0.25 10 false 2

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

After replacing the master cylinder solenoid, perform zero point calibration and store the system information (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>CALIBRATION).

·

When the start function does not operate, check the Entry and Start System(for start function) (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING).



PROCEDURE

1.CHECK STOP LIGHT OPERATION
a.

Check that the stop lights come on when the brake pedal is depressed and go off when the brake pedal is released.

OK:

The stop lights illuminate when the brake pedal is depressed. The stop lights turn off when the brake pedal is released.




OK

2.CHECK HARNESS AND CONNECTOR (MASTER CYLINDER SOLENOID [SKID CONTROL ECU] STPO TERMINAL VOLTAGE)

NG

2.CHECK HARNESS AND CONNECTOR (MASTER CYLINDER SOLENOID [SKID CONTROL ECU] STPO TERMINAL VOLTAGE)
a.

Disconnect the master cylinder solenoid (skid control ECU) connector.


b.
U156827E02
2.302,1.198 2.406,0.438 2.406,0.438 2.594,0.438 true 0.083,0.104 0.323,0.365 0.24,0.26 10 false *a 2.625,0.375 3.052,0.552 0.427,0.177 10 false STPO 1.656,0.417 1.948,0.573 0.292,0.156 10 false A24

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A24-16 (STPO) - Body ground Engine switch on (IG) 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Master Cylinder Solenoid [Skid Control ECU])



OK

3.CHECK HARNESS AND CONNECTOR (MASTER CYLINDER SOLENOID [SKID CONTROL ECU] STP2 TERMINAL VOLTAGE)

NG

7.CHECK HARNESS AND CONNECTOR (STOP LIGHT RELAY [STP LP OPE] - MASTER CYLINDER SOLENOID [SKID CONTLOR ECU] AND BATTERY)
3.CHECK HARNESS AND CONNECTOR (MASTER CYLINDER SOLENOID [SKID CONTROL ECU] STP2 TERMINAL VOLTAGE)
a.

Disconnect the master cylinder solenoid (skid control ECU) connector.


b.
U156828E06
2.24,1.406 2.469,1.885 2.469,1.885 2.656,1.885 true 0.083,0.052 0.323,0.313 0.24,0.26 10 false *a 2.708,1.792 3.135,1.969 0.427,0.177 10 false STP2 1.635,0.427 1.927,0.583 0.292,0.156 10 false A24

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A24-45 (STP2) - Body ground Brake pedal depressed 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Master Cylinder Solenoid [Skid Control ECU])



OK

4.PERFORM ACTIVE TEST USING GTS (STOP LIGHT RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.PERFORM ACTIVE TEST USING GTS (STOP LIGHT RELAY)
a.

Enter the following menus: Chassis / ABS/VSC/TRAC / Active Test.


b.

Perform the Active Test according to the display on the GTS.

ABS/VSC/TRAC
Tester Display Test Part Control Range Diagnostic Note
Stop Light Relay Stop light relay (STP LP OPE) Relay ON/OFF Observe the stop light (the stop lights do not come on for 2 to 5 seconds).


c.

Check the stop light relay (STP LP OPE) operation using the Data List and stop light operation by performing an Active Test.

ABS/VSC/TRAC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Stop Light Relay Output Stop light relay (STP LP OPE) output/ ON or OFF ON: Relay output on (Stop light on)
OFF: Relay output off (Stop light off)
-

Result
Result Proceed to
The Data List item "Stop Light Relay Output" switches between ON and OFF when turning the stop light control relay on and off with the Active Test, but the stop lights do not illuminate or turn off A
The Data List item "Stop Light Relay Output" does not switch between ON and OFF when turning the stop light control relay on and off with the Active Test (for LHD) B
The Data List item "Stop Light Relay Output" switches between ON and OFF when turning the stop light control relay on and off with the Active Test and the stop lights illuminate and turn off (for LHD)
The Data List item "Stop Light Relay Output" does not switch between ON and OFF when turning the stop light control relay on and off with the Active Test (for RHD) C
The Data List item "Stop Light Relay Output" switches between ON and OFF when turning the stop light control relay on and off with the Active Test and the stop lights illuminate and turn off (for RHD)



A

5.INSPECT STOP LIGHT RELAY (STP LP OPE)

B

REPLACE MASTER CYLINDER SOLENOID (SKID CONTROL ECU)

C

REPLACE MASTER CYLINDER SOLENOID (SKID CONTROL ECU)

5.INSPECT STOP LIGHT RELAY (STP LP OPE)
a.

Turn the engine switch off.


b.

Remove the stop light relay (STP LP OPE) from the engine room relay block and junction block assembly.


c.

Inspect the stop light relay (STP LP OPE) (See page Vehicle Exterior>LIGHTING (EXT)>RELAY>ON-VEHICLE INSPECTION).



OK

6.CHECK HARNESS AND CONNECTOR (STOP LIGHT RELAY [STP LP OPE] - BATTERY)

NG

REPLACE STOP LIGHT RELAY (STP LP OPE)

6.CHECK HARNESS AND CONNECTOR (STOP LIGHT RELAY [STP LP OPE] - BATTERY)
a.

Turn the engine switch off.


b.

Remove the stop light relay (STP LP OPE) from the engine room relay block and junction block assembly.


c.
E331226E08
0.146,0.125 0.542,0.375 0.396,0.25 10 false *1 2.698,1.75 3.094,2 0.396,0.25 10 false *2

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
Stop light relay (STP LP OPE) holder terminal 5 - Body ground Always 11 to 14 V


Text in Illustration
*1 Engine Room Relay Block and Junction Block Assembly
*2 Stop Light Relay (STP LP OPE) Holder Terminal

OK:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C




A

REPLACE MASTER CYLINDER SOLENOID (SKID CONTROL ECU)

B

REPLACE MASTER CYLINDER SOLENOID (SKID CONTROL ECU)

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (STOP LIGHT RELAY [STP LP OPE] - MASTER CYLINDER SOLENOID [SKID CONTLOR ECU] AND BATTERY)
a.

Turn the engine switch off.


b.

Remove the stop light relay (STP LP OPE) from the engine room relay block and junction block assembly.


c.

Disconnect the A24 master cylinder solenoid (skid control ECU) connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Stop light relay (STP LP OPE) holder terminal 2 - A24-16 (STPO) Always Below 1 Ω
Stop light relay (STP LP OPE) holder terminal 2 or A24-16 (STPO) - Body ground Always 10 kΩ or higher



e.
E331226E09
0.135,0.083 0.531,0.333 0.396,0.25 10 false *1 2.698,1.74 3.094,1.99 0.396,0.25 10 false *2

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
Stop light relay (STP LP OPE) holder terminal 1 - Body ground Engine switch on (IG) 11 to 14 V


Text in Illustration
*1 Engine Room Relay Block and Junction Block Assembly
*2 Stop Light Relay (STP LP OPE) Holder Terminal



OK

REPLACE STOP LIGHT RELAY (STP LP OPE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR