Home › Vehicle Interior › SEAT BELT › SEAT BELT WARNING SYSTEM › 2014.08–2015.08
RM2660E _58 Vehicle Interior _052846 SEAT BELT _0255651 SEAT BELT WARNING SYSTEM J

SEAT BELT  SEAT BELT WARNING SYSTEM  Front Passenger Side Seat Belt Warning Light Malfunction  


DESCRIPTION

The combination meter detects the state of the front seat inner belt assembly (for Front Passenger Side) when the front passenger seat is occupied with the ignition switch ON. If the front passenger seat belt is not fastened, the front passenger side seat belt warning light on the multi-display assembly*1 or clock assembly*2 blinks. If the seat belt is fastened, the warning light goes off.

*1: w/ Navigation System

*2: w/o Navigation System


WIRING DIAGRAM

C263393E02
5.875,0.802 6.354,0.958 0.479,0.156 10 false WRNP 3.885,0.802 4.344,0.958 0.458,0.156 10 false PBEW 3.927,2.469 4.313,2.625 0.385,0.156 10 false LAPL 4.396,2.375 4.542,2.531 0.146,0.156 10 false 8 4.396,0.719 4.51,0.875 0.115,0.156 10 false 9 4.531,3.76 4.813,3.917 0.281,0.156 10 false c22 4.615,3.583 4.729,3.74 0.115,0.156 10 false 3 4.573,3.958 4.771,4.115 0.198,0.156 10 false *4 4.229,3.958 4.427,4.115 0.198,0.156 10 false *3 1.521,3.896 2.76,4.281 1.24,0.385 10 true Occupant Detection Sensor 2.833,4.75 4.146,5.146 1.313,0.396 10 false Front Seat Inner Belt RH*3, LH*4 0.052,3.969 1.344,4.406 1.292,0.438 10 false Front Separate Type Seat Cushion Pad 0.042,5.76 1.333,6.198 1.292,0.438 10 false Front Separate Type Seat Cushion Pad 0.031,6.927 1.74,7.115 1.708,0.188 10 false *1: w/ Navigation System 0.031,7.188 1.74,7.375 1.708,0.188 10 false *2: w/o Navigation System 1.979,7.188 4.167,7.375 2.188,0.188 10 false *5: except Double Swing Out Type 1.979,7.438 4.094,7.625 2.115,0.188 10 false *6: for Double Swing Out Type 0.031,7.438 1.74,7.625 1.708,0.188 10 false *3: for LHD 1.979,6.927 2.76,7.115 0.781,0.188 10 false *4: for RHD 2.958,4.448 3.854,4.615 0.896,0.167 10 false Buckle Switch 4.219,3.76 4.396,3.917 0.177,0.156 10 false c7 4.26,3.583 4.375,3.74 0.115,0.156 10 false 3 2.667,3.677 2.781,3.833 0.115,0.156 10 false 1 2.667,4.438 2.781,4.594 0.115,0.156 10 false 3 1.521,5.708 2.781,6.073 1.26,0.365 10 false Occupant Detection Sensor 2.833,6.563 4.146,6.958 1.313,0.396 10 false Front Seat Inner Belt RH*3, LH*4 2.958,6.302 3.854,6.469 0.896,0.167 10 false Buckle Switch 2.667,5.51 2.781,5.667 0.115,0.156 10 false 1 2.667,6.25 2.781,6.406 0.115,0.156 10 false 3 4.531,4.333 4.813,4.49 0.281,0.156 10 false c22 4.615,4.156 4.729,4.313 0.115,0.156 10 false 4 4.573,4.531 4.771,4.688 0.198,0.156 10 false *4 4.229,4.531 4.427,4.688 0.198,0.156 10 false *3 4.219,4.333 4.396,4.49 0.177,0.156 10 false c7 4.26,4.156 4.375,4.313 0.115,0.156 10 false 4 4.531,5.583 4.813,5.74 0.281,0.156 10 false K43 4.583,5.406 4.771,5.563 0.188,0.156 10 false 13 4.573,5.781 4.771,5.938 0.198,0.156 10 false *4 4.229,5.781 4.427,5.938 0.198,0.156 10 false *3 4.188,5.583 4.458,5.74 0.271,0.156 10 false L49 3.979,5.5 4.094,5.656 0.115,0.156 10 false + 3.958,6.083 4.115,6.24 0.156,0.156 10 false E 4.219,5.406 4.406,5.563 0.188,0.156 10 false 13 4.531,6.156 4.813,6.313 0.281,0.156 10 false K43 4.615,5.979 4.729,6.135 0.115,0.156 10 false 9 4.573,6.354 4.771,6.51 0.198,0.156 10 false *4 4.219,6.354 4.417,6.51 0.198,0.156 10 false *3 4.167,6.156 4.427,6.313 0.26,0.156 10 false L49 4.25,5.979 4.365,6.135 0.115,0.156 10 false 9 3.375,0.51 3.563,0.667 0.188,0.156 10 false IG 3.396,2.146 3.708,2.302 0.313,0.156 10 false IG+ 3.125,2.073 3.313,2.229 0.188,0.156 10 false 10 3.396,2.688 3.521,2.844 0.125,0.156 10 false E 3.208,2.604 3.313,2.76 0.104,0.156 10 false 1 3.146,0.427 3.333,0.583 0.188,0.156 10 false 23 3.042,1.396 3.323,1.552 0.281,0.156 10 false F79 3.375,1.125 3.802,1.281 0.427,0.156 10 false GND1 2.052,0.646 2.906,0.802 0.854,0.156 10 false ECU-IG No.1 2.177,2.292 3.042,2.448 0.865,0.156 10 false ECU-IG No.2 0.125,0.5 1.479,0.698 1.354,0.198 10 false from IG1 NO. 1 Relay 0.125,2.156 1.479,2.344 1.354,0.188 10 false from IG1 NO. 3 Relay 3.146,1.042 3.323,1.198 0.177,0.156 10 false 13 5.594,0.708 5.802,0.865 0.208,0.156 10 false 22 5.875,3.781 6.354,3.938 0.479,0.156 10 false P/SB 5.677,3.688 5.792,3.844 0.115,0.156 10 false 7 5.167,0.885 5.375,1.042 0.208,0.156 10 false *1 3.042,1.542 4.75,1.698 1.708,0.156 10 false Multi-display Assembly*1 3.656,3.031 3.854,3.188 0.198,0.156 10 false g1 3.656,3.198 4.167,3.354 0.51,0.156 10 false Clock*2 5.792,4.615 5.99,4.771 0.198,0.156 10 false E7 5.792,4.771 7.042,4.927 1.25,0.156 10 false Combination Meter 5.167,2.552 5.375,2.708 0.208,0.156 10 false *2 4.927,3.854 5.135,4.01 0.208,0.156 10 false *5 5.198,5.677 5.406,5.833 0.208,0.156 10 false *6

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK VEHICLE TYPE
a.

Check the vehicle type.

Result
Result Proceed to
except Double Swing Out Type A
for Double Swing Out Type B



A

2.CHECK FOR DTC

B

13.READ VALUE USING INTELLIGENT TESTER (PASSENGER SIDE BUCKLE SWITCH)
2.CHECK FOR DTC
a.

Check for DTCs.

Result
Result Proceed to
DTC is not output A
CAN communication system DTC is output (for LHD) B
CAN communication system DTC is output (for RHD) C
Airbag system DTC is output D



A

3.READ VALUE USING INTELLIGENT TESTER (PASSENGER SIDE BUCKLE SWITCH)

B

C

D

3.READ VALUE USING INTELLIGENT TESTER (PASSENGER SIDE BUCKLE SWITCH)
a.

Check the Data List for proper functioning of the front passenger side seat belt buckle switch.

Combination Meter
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
P-Seatbelt Buckle SW Front passenger side seat belt buckle signal / ON or OFF ON: Front passenger side seat is occupied, front passenger side seat belt is fastened
OFF: Front passenger side seat is occupied, front passenger side seat belt is unfastened
-

OK:

The display is as specified in the normal condition column.




OK

4.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (FRONT PASSENGER SIDE SEAT BELT WARNING LIGHT)

NG

9.CHECK HARNESS AND CONNECTOR (FRONT SEAT INNER BELT - COMBINATION METER AND BODY GROUND)
4.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (FRONT PASSENGER SIDE SEAT BELT WARNING LIGHT)
a.

Operate the intelligent tester according to the steps on the display and select Active Test.

Combination Meter
Item Test Part Control Range Diagnostic Note
Front Passenger Side Seat Belt Front passenger side seat belt warning light ON or OFF Confirm that the vehicle is stopped and the engine is idling.

Result
Result Proceed to
Front passenger side seat belt warning light condition cannot be switched by Active Test (w/ Navigation System) A
Front passenger side seat belt warning light condition cannot be switched by Active Test (w/o Navigation System) B
Front passenger side seat belt warning light condition can be switched by Active Test (w/ Multi-information Display) C
Front passenger side seat belt warning light condition can be switched by Active Test (w/o Multi-information Display) D



A

5.CHECK HARNESS AND CONNECTOR (MULTI-DISPLAY ASSEMBLY - COMBINATION METER, BATTERY AND BODY GROUND)

B

7.CHECK HARNESS AND CONNECTOR (CLOCK - COMBINATION METER, BATTERY AND BODY GROUND)

C

D

5.CHECK HARNESS AND CONNECTOR (MULTI-DISPLAY ASSEMBLY - COMBINATION METER, BATTERY AND BODY GROUND)
a.

Disconnect the F79 multi-display assembly connectors.


b.

Disconnect the E7 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F79-9 (PBEW) - E7-22 (WRNP) Always Below 1 Ω
F79-9 (PBEW) or E7-22 (WRNP) - Body ground Always 10 kΩ or higher
F79-13 (GND1) - Body ground Always Below 1 Ω



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F79-23 (IG) - Body ground Ignition switch ON 11 to 14 V




OK

6.CHECK MULTI-DISPLAY ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK MULTI-DISPLAY ASSEMBLY
a.
U164296E01
1.563,0.19 1.820,0.337 0.258,0.147 10 F79 2.886,1.711 3.317,1.858 0.431,0.147 10 GND1 0.412,0.225 0.850,0.372 0.438,0.147 10 PBEW 0.516,1.797 0.704,1.944 0.188,0.147 10 IG 0.933,0.317 1.295,0.999 false 0.728,1.876 0.946,1.31 false 2.687,1.314 2.87,1.79 false 0.05,0.027 0.204,0.173 0.154,0.147 10 *1

Disconnect the F79 multi-display assembly connectors.


b.

Apply battery voltage to the terminals and check that the front passenger seat belt warning light illuminates.

OK:
Measurement Connection Specified Condition
Battery Positive (+) → 23 (IG)
Battery negative (-) → 9 (PBEW)
Battery negative (-) → 13 (GND1)
Front passenger side seat belt warning light on


Text in Illustration
*1 Component without harness connected
(Multi-display Assembly)

Result
Result Proceed to
NG A
OK (w/ Multi-information Display) B
OK (w/o Multi-information Display) C



A

B

C

7.CHECK HARNESS AND CONNECTOR (CLOCK - COMBINATION METER, BATTERY AND BODY GROUND)
a.

Disconnect the g1 clock assembly connector.


b.

Disconnect the E7 combination meter assembly connector.


c.

Measure the resistance and voltage according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
g1-1 (E) - Body ground Always Below 1 Ω
g1-8 (LAPL) - Body ground Always 10 kΩ or higher
g1-8 (LAPL) - E7-22 (WRNP) Always Below 1 Ω



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
g1-10 (IG+) - Body ground Ignition switch ON 11 to 14 V




OK

8.CHECK CLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK CLOCK ASSEMBLY
a.
E156389E07
2.656,0.813 2.375,0.813 2.375,0.813 2.25,1.229 true 2.219,1.833 2.01,1.552 true 1.24,1.865 1.406,1.865 1.406,1.865 1.635,1.552 true 2.75,0.74 2.969,0.885 0.219,0.146 10 false E 0.969,1.781 1.323,1.969 0.354,0.188 10 false IG+ 2.156,1.885 2.656,2.073 0.5,0.188 10 false LAPL 0.167,0.135 0.729,0.385 0.563,0.25 10 false *1

Disconnect the g1 clock assembly connector.


b.

Apply battery voltage to the terminals and check that the front passenger seat belt warning light illuminates.

OK:
Measurement Connection Specified Condition
Battery Positive (+) → 10 (IG+)
Battery negative (-) → 8 (LAPL)
Battery negative (-) → 1 (E)
Front passenger seat belt warning light Illuminates


Text in Illustration
*1 Component without harness connected
(Clock Assembly)

Result
Result Proceed to
NG A
OK (w/ Multi-information Display) B
OK (w/o Multi-information Display) C



A

B

C

9.CHECK HARNESS AND CONNECTOR (FRONT SEAT INNER BELT - COMBINATION METER AND BODY GROUND)
a.

Disconnect the c7*1 or c22*2 front seat inner belt assembly (for Front Passenger Side) connector.

*1: for LHD

*2: for RHD



b.

Disconnect the E7 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD:
Tester Connection Condition Specified Condition
c7-3 - E7-7 (P/SB) Always Below 1 Ω
c7-3 or E7-7 (P/SB) - Body ground Always 10 kΩ or higher
c7-4 - Body ground Always Below 1 Ω


Standard Resistance:
for LHD:
Tester Connection Condition Specified Condition
c22-3 - E7-7 (P/SB) Always Below 1 Ω
c22-3 or E7-7 (P/SB) - Body ground Always 10 kΩ or higher
c22-4 - Body ground Always Below 1 Ω




OK

10.INSPECT FRONT SEPARATE TYPE SEAT CUSHION PAD (OCCUPANT DETECTION SENSOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.INSPECT FRONT SEPARATE TYPE SEAT CUSHION PAD (OCCUPANT DETECTION SENSOR)

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 3 More than 147 N (15 kgf, 33.0 lbf) applied to occupant detection sensor Below 100 Ω


Result
Result Proceed to
OK A
NG (for Manual Seat) B
NG (for Power Seat) C
NG (for Bench Seat) D



A

11.REPLACE FRONT SEAT INNER BELT ASSEMBLY (for Front Passenger Side)

B

REPLACE FRONT SEPARATE TYPE SEAT CUSHION PAD

C

REPLACE FRONT SEPARATE TYPE SEAT CUSHION PAD

D

REPLACE FRONT SEPARATE TYPE SEAT CUSHION PAD

11.REPLACE FRONT SEAT INNER BELT ASSEMBLY (for Front Passenger Side)
a.

Temporarily replace the front seat inner belt assembly RH*1 or LH*2 with a new one.

*1: for LHD

*2: for RHD





NEXT

12.CHECK FRONT PASSENGER SIDE SEAT BELT WARNING LIGHT
12.CHECK FRONT PASSENGER SIDE SEAT BELT WARNING LIGHT
a.

Check the front passenger side seat belt warning light function (See page Vehicle Interior>SEAT BELT>SEAT BELT WARNING SYSTEM>OPERATION CHECK).

OK:

Front passenger side seat belt warning light operates normally.


Result
Result Proceed to
OK A
NG (w/ Multi-information Display) B
NG (w/o Multi-information Display) C



A

END (FRONT SEAT INNER BELT ASSEMBLY IS DEFECTIVE)

B

C

13.READ VALUE USING INTELLIGENT TESTER (PASSENGER SIDE BUCKLE SWITCH)
a.

Check the Data List for proper functioning of the front passenger side seat belt buckle switch.

Combination Meter
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
P-Seatbelt Buckle SW Front passenger side seat belt buckle signal / ON or OFF ON: Front passenger side seat is occupied, front passenger side seat belt is fastened
OFF: Front passenger side seat is occupied, front passenger side seat belt is unfastened
-

OK:

The display is as specified in the normal condition column.




OK

14.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (FRONT PASSENGER SIDE SEAT BELT WARNING LIGHT)

NG

17.INSPECT FRONT SEAT INNER BELT ASSEMBLY (for Front Passenger Side)
14.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (FRONT PASSENGER SIDE SEAT BELT WARNING LIGHT)
a.

Operate the intelligent tester according to the steps on the display and select Active Test.

Combination Meter
Item Test Part Control Range Diagnostic Note
Front Passenger Side Seat Belt Front passenger side seat belt warning light ON or OFF Confirm that the vehicle is stopped and the engine is idling.

OK:

Passenger side seat belt warning light condition can be switched by Active Test.




OK

NG

15.CHECK HARNESS AND CONNECTOR (CLOCK - COMBINATION METER, BATTERY AND BODY GROUND)
15.CHECK HARNESS AND CONNECTOR (CLOCK - COMBINATION METER, BATTERY AND BODY GROUND)
a.

Disconnect the g1 clock assembly connector.


b.

Disconnect the E7 combination meter assembly connector.


c.

Measure the resistance and voltage according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
g1-1 (E) - Body ground Always Below 1 Ω
g1-8 (LAPL) - E7-22 (WRNP) Always Below 1 Ω
g1-8 (LAPL) - Body ground Always 10 kΩ or higher




OK

16.CHECK CLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

16.CHECK CLOCK ASSEMBLY
a.
E156389E08
2.646,0.792 2.385,0.792 2.385,0.792 2.167,1.198 true 2.479,1.885 2.26,1.885 2.26,1.885 2.01,1.552 true 1.198,1.885 1.375,1.885 1.375,1.885 1.635,1.594 true 2.708,0.729 2.927,0.865 0.219,0.135 10 false E 0.958,1.813 1.313,2.021 0.354,0.208 10 false IG+ 2.563,1.813 3.156,1.99 0.594,0.177 10 false LAPL 0.219,0.167 0.542,0.302 0.323,0.135 10 false *1

Disconnect the g1 clock assembly connector.


b.

Apply battery voltage to the terminals and check that the front passenger seat belt warning light illuminates.

OK:
Measurement Connection Specified Condition
Battery Positive (+) → 10 (IG+)
Battery negative (-) → 8 (LAPL)
Battery negative (-) → 1 (E)
Front passenger seat belt warning light Illuminates


Text in Illustration
*1 Component without harness connected
(Clock Assembly)



OK

NG

17.INSPECT FRONT SEAT INNER BELT ASSEMBLY (for Front Passenger Side)
a.
C246933

Remove the front seat inner belt assembly (for Front Passenger Side).



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
13 - 9 Seat belt unfastened (buckle switch is off) Below 1 Ω
Seat belt fastened (buckle switch is on) 10 kΩ or higher


Result
Result Proceed to
OK A
NG (except Bench Seat) B
NG (for Bench seat) C



A

18.INSPECT FRONT SEPARATE TYPE SEAT CUSHION PAD

B

REPLACE FRONT SEAT INNER BELT ASSEMBLY (for Front Passenger Side)

C

REPLACE FRONT SEAT INNER BELT ASSEMBLY (for Front Passenger Side)

18.INSPECT FRONT SEPARATE TYPE SEAT CUSHION PAD
a.
B294030

Remove the front separate type seat cushion pad.



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 3 More than 147 N (15 kgf, 33.0 lbf) applied to occupant detection sensor Below 100 Ω


Result
Result Proceed to
OK A
NG (except Bench Seat) B
NG (for Bench Seat) C



A

19.CHECK HARNESS AND CONNECTOR (FRONT SEAT INNER BELT - COMBINATION METER AND BODY GROUND)

B

REPLACE FRONT SEPARATE TYPE SEAT CUSHION PAD

C

REPLACE FRONT SEPARATE TYPE SEAT CUSHION PAD

19.CHECK HARNESS AND CONNECTOR (FRONT SEAT INNER BELT - COMBINATION METER AND BODY GROUND)
a.

Disconnect the L49*1 or K43*2 front seat inner belt assembly (for Front Passenger Side) connector.


b.

Disconnect the E7 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD:
Tester Connection Condition Specified Condition
L49-13 - E7-7 (P/SB) Always Below 1 Ω
L49-13 or E7-7 (P/SB) - Body ground Always 10 kΩ or higher
L49-9 - Body ground Always Below 1 Ω

for RHD:
Tester Connection Condition Specified Condition
K43-13 - E7-7 (P/SB) Always Below 1 Ω
K43-13 or E7-7 (P/SB) - Body ground Always 10 kΩ or higher
K43-9 - Body ground Always Below 1 Ω




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR