Home › Vehicle Interior › SEAT BELT › SEAT BELT WARNING SYSTEM › from 2015.08
RM2660E _58 Vehicle Interior _052846 SEAT BELT _0255651 SEAT BELT WARNING SYSTEM J

SEAT BELT  SEAT BELT WARNING SYSTEM  Front Passenger Side Seat Belt Warning Light Malfunction  


DESCRIPTION

The combination meter detects the state of the front seat inner belt assembly (for Front Passenger Side) when the front passenger seat is occupied with the ignition switch ON. If the front passenger seat belt is not fastened, the front passenger side seat belt warning light on the multi-media module receiver assembly*1 (clock assembly*2) blinks. If the seat belt is fastened, the warning light goes off.

*1: w/ Navigation System

*2: w/o Navigation System


WIRING DIAGRAM

B431365E03
4.656,2.635 5.125,2.792 0.469,0.156 10 false E120 0.25,1.188 2.094,1.406 1.844,0.219 10 false Occupant Detection Sensor 2.49,3.698 4.5,4.094 2.01,0.396 10 false Front Seat Inner Belt Assembly LH*1, RH*2 2.479,3.51 4.677,3.719 2.198,0.208 10 false c70*1*3, c7*2*4, c42*2*3, c22*2*4 0.333,1.635 2.406,2.146 2.073,0.51 10 false Front Separate Type Seat Cushion Pad LH*1, RH*2 0.208,8.063 1.917,8.25 1.708,0.188 10 false *1: for LHD 0.208,8.406 0.99,8.594 0.781,0.188 10 false *2: for RHD 2.323,0.865 2.438,1.021 0.115,0.156 10 false 1 2.323,0.406 2.438,0.563 0.115,0.156 10 false 3 4.063,0.396 4.167,0.552 0.104,0.156 10 false 1 4.063,0.854 4.167,1.01 0.104,0.156 10 false 2 4.74,0.313 4.927,0.469 0.188,0.156 10 false 13 5.104,0.51 5.573,0.667 0.469,0.156 10 false PDOS 4.792,2.438 4.896,2.594 0.104,0.156 10 false 9 5.104,2.635 5.573,2.792 0.469,0.156 10 false PBKL 4.75,4.677 5.031,4.833 0.281,0.156 10 false 11 5.104,4.906 5.573,5.063 0.469,0.156 10 false WRNP 2.385,4.875 2.844,5.031 0.458,0.156 10 false PBEW 2.917,4.792 3.385,4.948 0.469,0.156 10 false 38 3.823,0.396 3.927,0.552 0.104,0.156 10 false + 3.792,0.865 3.979,1.021 0.188,0.156 10 false E 4.063,2.521 4.167,2.677 0.104,0.156 10 false 3 4.063,2.854 4.167,3.01 0.104,0.156 10 false 4 3.823,2.521 3.927,2.677 0.104,0.156 10 false + 3.792,2.854 3.979,3.01 0.188,0.156 10 false E 1.542,5.635 3.094,6.031 1.552,0.396 10 false Multi-media Module Receiver Assembly 1.542,5.479 2.167,5.635 0.625,0.156 10 false F76 4.99,7.073 6.865,7.229 1.875,0.156 10 false Combination Meter Assembly 4.656,0.51 5.125,0.667 0.469,0.156 10 false E120 4.656,4.875 5.125,5.031 0.469,0.156 10 false E120 1.302,8.063 3.635,8.25 2.333,0.188 10 false *3: w/ Climate Control System 1.302,8.406 3.719,8.594 2.417,0.188 10 false *4: w/o Climate Control System

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK VEHICLE TYPE
a.

Check the vehicle type.

Result
Result Proceed to
for LHD A
for RHD B



A

2.CHECK FOR DTC

B

13.CHECK FOR DTC
2.CHECK FOR DTC
a.

Check for DTCs.

Result
Result Proceed to
DTC is not output A
CAN communication system DTC is output (for LHD with Central Gateway ECU) B
CAN communication system DTC is output (for LHD without Central Gateway ECU) C
Airbag system DTC is output D



A

3.READ VALUE USING GTS (PASSENGER SIDE BUCKLE SWITCH)

B

C

D

3.READ VALUE USING GTS (PASSENGER SIDE BUCKLE SWITCH)
a.

Check the Data List for proper functioning of the front passenger side seat belt buckle switch.

Combination Meter
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
P-Seatbelt Buckle SW Front passenger side seat belt buckle signal / ON or OFF ON: Front passenger side seat belt is fastened
OFF: Front passenger side seat belt is unfastened
-
Passenger Occupant Detection Switch Occupant detection sensor signal / ON or OFF ON: Front passenger seat occupied
OFF: Front passenger seat not occupied
-

Result
Result Proceed to
ON or OFF is displayed on the GTS screen according (w/ Navigation System) A
ON or OFF is displayed on the GTS screen according (w/o Navigation System) B
ON or OFF is not displayed normally on the GTS screen according to the front passenger side seat belt condition C
ON or OFF is not displayed normally on the GTS screen according to the front passenger seat condition (occupied or unoccupied) D



A

4.CHECK HARNESS AND CONNECTOR (MULTI-MEDIA MODULE RECEIVER ASSEMBLY - COMBINATION METER ASSEMBLY, BATTERY AND BODY GROUND)

B

6.CHECK HARNESS AND CONNECTOR (CLOCK ASSEMBLY - COMBINATION METER ASSEMBLY, BATTERY AND BODY GROUND)

C

8.INSPECT FRONT SEAT INNER BELT ASSEMBLY LH

D

10.INSPECT FRONT SEPARATE TYPE SEAT CUSHION PAD LH (OCCUPANT DETECTION SENSOR)
4.CHECK HARNESS AND CONNECTOR (MULTI-MEDIA MODULE RECEIVER ASSEMBLY - COMBINATION METER ASSEMBLY, BATTERY AND BODY GROUND)
a.

Disconnect the F77 multi-media module receiver assembly connector.


b.

Disconnect the E119 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F77-38 (PBEW) - E119-11 (WRNP) Always Below 1 Ω
F77-38 (PBEW) or E119-11 (WRNP) - Body ground Always 10 kΩ or higher




OK

5.CHECK MULTI-MEDIA MODULE RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK MULTI-MEDIA MODULE RECEIVER ASSEMBLY
a.
U164342E02
0.823,1.115 1.01,1.667 1.01,1.667 1.167,1.667 true 1.583,0.24 1.979,0.396 0.396,0.156 10 false F77 1.24,1.594 1.865,1.75 0.625,0.156 10 false WRNP

Disconnect the F77 multi-media module receiver assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F77-38 (WRNP) - Body ground Ignition switch ON 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Multi-media Module Receiver Assembly)



OK

REPLACE COMBINATION METER ASSEMBLY

NG

6.CHECK HARNESS AND CONNECTOR (CLOCK ASSEMBLY - COMBINATION METER ASSEMBLY, BATTERY AND BODY GROUND)
a.

Disconnect the g2 clock assembly connector.


b.

Disconnect the E119 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
g2-14 (LAPL) or E119-11 (WRNP) - Body ground Always 10 kΩ or higher
g2-14 (LAPL) - E119-11 (WRNP) Always Below 1 Ω




OK

7.CHECK CLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK CLOCK ASSEMBLY
a.
U166604E02
1.427,1.479 1.229,1.938 1.229,1.938 1.125,1.938 true 1.583,0.156 2,0.313 0.417,0.156 10 false g2 0.656,1.854 1.073,2.01 0.417,0.156 10 false LAPL 0.167,0.104 0.583,0.26 0.417,0.156 10 false *a

Disconnect the g2 clock assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
g2-14 (LAPL) - Body ground Ignition switch ON 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Clock Assembly)



OK

REPLACE COMBINATION METER ASSEMBLY

NG

8.INSPECT FRONT SEAT INNER BELT ASSEMBLY LH
a.

Remove the front seat inner belt assembly LH.



b.

Inspect the front seat inner belt assembly LH.


Result
Result Proceed to
OK A
NG (except Bench Seat) B
NG (for Bench seat) C



A

9.CHECK HARNESS AND CONNECTOR (FRONT SEAT INNER BELT ASSEMBLY LH - COMBINATION METER ASSEMBLY, BATTERY AND BODY GROUND)

B

REPLACE FRONT SEAT INNER BELT ASSEMBLY (for Front Passenger Side)

C

REPLACE FRONT SEAT INNER BELT ASSEMBLY (for Front Passenger Side)

9.CHECK HARNESS AND CONNECTOR (FRONT SEAT INNER BELT ASSEMBLY LH - COMBINATION METER ASSEMBLY, BATTERY AND BODY GROUND)
a.

Disconnect the c7 front seat inner belt assembly LH connector.


b.

Disconnect the E120 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
c7-3 (+) - E120-9 (PBKL) Always Below 1 Ω
c7-3 (+) or E120-9 (PBKL) - Body ground Always 10 kΩ or higher
c7-4 (E) - Body ground Always Below 1 Ω




OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.INSPECT FRONT SEPARATE TYPE SEAT CUSHION PAD LH (OCCUPANT DETECTION SENSOR)
a.
B294030E02
0.172,0.079 0.506,0.271 0.334,0.192 10 *a

Remove the front separate type seat cushion pad LH.



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 3 Front passenger seat occupied Below 100 Ω
1 - 3 Front passenger seat not occupied 10 kΩ or higher


Result
Result Proceed to
OK A
NG (for Manual Seat) B
NG (for Power Seat) C
NG (for Bench Seat) D

Text in Illustration
*a Component without harness connected
(Occupant Detection Sensor)



A

11.INSPECT FRONT SEAT INNER BELT ASSEMBLY LH

B

REPLACE FRONT SEPARATE TYPE SEAT CUSHION PAD

C

REPLACE FRONT SEPARATE TYPE SEAT CUSHION PAD

D

REPLACE FRONT SEPARATE TYPE SEAT CUSHION PAD

11.INSPECT FRONT SEAT INNER BELT ASSEMBLY LH
a.

Remove the front seat inner belt assembly LH.



b.

Inspect the front seat inner belt assembly LH.


Result
Result Proceed to
OK A
NG (except Bench Seat) B
NG (for Bench seat) C



A

12.CHECK HARNESS AND CONNECTOR (FRONT SEAT INNER BELT LH - COMBINATION METER ASSEMBLY AND BODY GROUND)

B

REPLACE FRONT SEAT INNER BELT ASSEMBLY (for Front Passenger Side)

C

REPLACE FRONT SEAT INNER BELT ASSEMBLY (for Front Passenger Side)

12.CHECK HARNESS AND CONNECTOR (FRONT SEAT INNER BELT LH - COMBINATION METER ASSEMBLY AND BODY GROUND)
a.

Disconnect the c7 front seat inner belt assembly LH connector.


b.

Disconnect the E119 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
c7-1 (+) - E119-13 (PODS) Always Below 1 Ω
c7-1 (+) or E119-13 (PODS) - Body ground Always 10 kΩ or higher
c7-2 (E) - Body ground Always Below 1 Ω




OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.CHECK FOR DTC
a.

Check for DTCs.

Result
Result Proceed to
DTC is not output A
CAN communication system DTC is output (for RHD with Central Gateway ECU) B
CAN communication system DTC is output (for RHD without Central Gateway ECU) C
Airbag system DTC is output D



A

14.READ VALUE USING GTS (PASSENGER SIDE BUCKLE SWITCH)

B

C

D

14.READ VALUE USING GTS (PASSENGER SIDE BUCKLE SWITCH)
a.

Check the Data List for proper functioning of the front passenger side seat belt buckle switch.

Combination Meter
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
P-Seatbelt Buckle SW Front passenger side seat belt buckle signal / ON or OFF ON: Front passenger side seat belt is fastened
OFF: Front passenger side seat belt is unfastened
-
Passenger Occupant Detection Switch Occupant detection sensor signal / ON or OFF ON: Front passenger seat occupied
OFF: Front passenger seat not occupied
-

Result
Result Proceed to
ON or OFF is displayed on the GTS screen according (w/ Navigation System) A
ON or OFF is displayed on the GTS screen according (w/o Navigation System) B
ON or OFF is not displayed normally on the GTS screen according to the front passenger side seat belt condition C
ON or OFF is not displayed normally on the GTS screen according to the front passenger seat condition (occupied or unoccupied) D



A

15.CHECK HARNESS AND CONNECTOR (MULTI-MEDIA MODULE RECEIVER ASSEMBLY - COMBINATION METER ASSEMBLY, BATTERY AND BODY GROUND)

B

17.CHECK HARNESS AND CONNECTOR (CLOCK ASSEMBLY - COMBINATION METER ASSEMBLY, BATTERY AND BODY GROUND)

C

19.INSPECT FRONT SEAT INNER BELT ASSEMBLY RH

D

21.INSPECT FRONT SEPARATE TYPE SEAT CUSHION PAD RH (OCCUPANT DETECTION SENSOR)
15.CHECK HARNESS AND CONNECTOR (MULTI-MEDIA MODULE RECEIVER ASSEMBLY - COMBINATION METER ASSEMBLY, BATTERY AND BODY GROUND)
a.

Disconnect the F77 multi-media module receiver assembly connector.


b.

Disconnect the E119 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F77-38 (PBEW) - E119-11 (WRNP) Always Below 1 Ω
F77-38 (PBEW) or E119-11 (WRNP) - Body ground Always 10 kΩ or higher




OK

16.CHECK COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

16.CHECK COMBINATION METER ASSEMBLY
a.
U164343E02
0.833,1.104 1.021,1.656 1.021,1.656 1.177,1.656 true 1.563,0.219 1.958,0.375 0.396,0.156 10 false F95 1.24,1.573 1.865,1.729 0.625,0.156 10 false PBEW

Disconnect the F77 multi-media module receiver assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F77-38 (PBEW) - Body ground Ignition switch ON 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Multi-media Module Receiver Assembly)



OK

REPLACE COMBINATION METER ASSEMBLY

NG

17.CHECK HARNESS AND CONNECTOR (CLOCK ASSEMBLY - COMBINATION METER ASSEMBLY, BATTERY AND BODY GROUND)
a.

Disconnect the g2 clock assembly connector.


b.

Disconnect the E119 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
g2-14 (LAPL) or E119-11 (WRNP) - Body ground Always 10 kΩ or higher
g2-14 (LAPL) - E119-11 (WRNP) Always Below 1 Ω




OK

18.CHECK CLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

18.CHECK CLOCK ASSEMBLY
a.
U166604E03
1.427,1.479 1.229,1.938 1.229,1.938 1.125,1.938 true 1.583,0.156 2,0.313 0.417,0.156 10 false g2 0.656,1.854 1.073,2.01 0.417,0.156 10 false LAPL 0.073,0.104 0.49,0.26 0.417,0.156 10 false *a

Disconnect the g2 clock assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
g2-14 (LAPL) - Body ground Ignition switch ON 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Clock Assembly)



OK

REPLACE COMBINATION METER ASSEMBLY

NG

19.INSPECT FRONT SEAT INNER BELT ASSEMBLY RH
a.

Remove the front seat inner belt assembly RH.



b.

Inspect the front seat inner belt assembly RH.


Result
Result Proceed to
OK A
NG (except Bench Seat) B
NG (for Bench seat) C



A

20.CHECK HARNESS AND CONNECTOR (FRONT SEAT INNER BELT ASSEMBLY RH - COMBINATION METER ASSEMBLY, BATTERY AND BODY GROUND)

B

REPLACE FRONT SEAT INNER BELT ASSEMBLY (for Front Passenger Side)

C

REPLACE FRONT SEAT INNER BELT ASSEMBLY (for Front Passenger Side)

20.CHECK HARNESS AND CONNECTOR (FRONT SEAT INNER BELT ASSEMBLY RH - COMBINATION METER ASSEMBLY, BATTERY AND BODY GROUND)
a.

Disconnect the c22 front seat inner belt assembly RH connector.


b.

Disconnect the E120 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
c22-3 (+) - E120-9 (PBKL) Always Below 1 Ω
c22-3 (+) or E120-9 (PBKL) - Body ground Always 10 kΩ or higher
c22-4 (E) - Body ground Always Below 1 Ω




OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

21.INSPECT FRONT SEPARATE TYPE SEAT CUSHION PAD RH (OCCUPANT DETECTION SENSOR)
a.
B294030E02
0.172,0.079 0.506,0.271 0.334,0.192 10 *a

Remove the front separate type seat cushion pad RH.



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 3 Front passenger seat occupied Below 100 Ω
1 - 3 Front passenger seat not occupied 10 kΩ or higher


Result
Result Proceed to
OK A
NG (for Manual Seat) B
NG (for Power Seat) C
NG (for Bench Seat) D



A

22.INSPECT FRONT SEAT INNER BELT ASSEMBLY RH

B

REPLACE FRONT SEPARATE TYPE SEAT CUSHION PAD

C

REPLACE FRONT SEPARATE TYPE SEAT CUSHION PAD

D

REPLACE FRONT SEPARATE TYPE SEAT CUSHION PAD

22.INSPECT FRONT SEAT INNER BELT ASSEMBLY RH
a.

Remove the front seat inner belt assembly RH.



b.

Inspect the front seat inner belt assembly RH.


Result
Result Proceed to
OK A
NG (except Bench Seat) B
NG (for Bench seat) C



A

23.CHECK HARNESS AND CONNECTOR (FRONT SEAT INNER BELT RH - COMBINATION METER ASSEMBLY AND BODY GROUND)

B

REPLACE FRONT SEAT INNER BELT ASSEMBLY (for Front Passenger Side)

C

REPLACE FRONT SEAT INNER BELT ASSEMBLY (for Front Passenger Side)

23.CHECK HARNESS AND CONNECTOR (FRONT SEAT INNER BELT RH - COMBINATION METER ASSEMBLY AND BODY GROUND)
a.

Disconnect the c22*1 or c42*2 front seat inner belt assembly RH connector.

*1: w/o Climate Control System

*2: w/ Climate Control System



b.

Disconnect the E119 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/ Climate Control System:
Tester Connection Condition Specified Condition
c42-1 (+) - E119-13 (PODS) Always Below 1 Ω
c42-1 (+) or E119-13 (PODS) - Body ground Always 10 kΩ or higher
c42-2 (E) - Body ground Always Below 1 Ω


Standard Resistance:
w/o Climate Control System:
Tester Connection Condition Specified Condition
c22-1 (+) - E119-13 (PODS) Always Below 1 Ω
c22-1 (+) or E119-13 (PODS) - Body ground Always 10 kΩ or higher
c22-2 (E) - Body ground Always Below 1 Ω




OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR