Home › Vehicle Interior › HEATING / AIR CONDITIONING › CONDENSER › 2014.08–2015.08
RM2660E _58 Vehicle Interior _052847 HEATING / AIR CONDITIONING _0255697 CONDENSER A

HEATING / AIR CONDITIONING  CONDENSER  INSTALLATION  


PROCEDURE

Hide 88474 1.INSTALL COOLER DRYER

a.
E050386

Using pliers, install the cooler dryer.


b.
E345456

Apply a sufficient amount of compressor oil to the contact surfaces of a new O-ring and the cap.

Compressor oil:

ND-OIL 8 or equivalent



c.

Install O-ring to the cap.


d.
I030086

Using a 14 mm socket hexagon wrench, install the cap to the modulator.

Torque:
2.9 N*m (30 kgf*cm, 26 in.*lbf)


Hide 88460 2.INSTALL COOLER CONDENSER ASSEMBLY

a.
E154210

Install the cooler condenser as shown in the illustration.

HINT:

If the cooler condenser assembly is replaced with a new one, add compressor oil to the new cooler condenser assembly.


Capacity:

40 cc (1.35 fl.oz)


Compressor oil:

ND-OIL 8 or equivalent



Hide 53201 3.INSTALL RADIATOR SUPPORT SUB-ASSEMBLY

E154816E02
0.615,0.396 0.74,0.604 0.125,0.208 10 true A 0.854,1.646 0.979,1.833 0.125,0.188 10 true A 3.24,0.896 3.354,1.052 0.115,0.156 10 true A 2.979,0.073 3.094,0.229 0.115,0.156 10 true A 1.104,0.104 1.219,0.271 0.115,0.167 10 true B

a.

Install the radiator support with the 8 bolts.

Torque:
21.7 N*m (221 kgf*cm, 16 ft.*lbf)

for bolt A

9.8 N*m (100 kgf*cm, 7 ft.*lbf)

for bolt B



Hide 53209B 6.INSTALL HOOD LOCK SUPPORT BRACE SUB-ASSEMBLY

E154814

a.

Install the brace with the 3 bolts and nut.

Torque:
21.7 N*m (221 kgf*cm, 16 ft.*lbf)

for bolt

5.5 N*m (56 kgf*cm, 49 in.*lbf)

for nut



b.

Install the hood lock nut cap.


Hide 32910 7.INSTALL OIL COOLER ASSEMBLY (w/ Air Cooled Transmission Oil Cooler)

a.
U164621E02
1.75,0.333 2.344,0.198 false 2.417,0.104 2.813,0.292 0.396,0.188 10 false Claw 0.708,0.792 0.823,0.948 0.115,0.156 10 false 3 2.313,3.063 2.427,3.219 0.115,0.156 10 false 4 0.677,3.073 0.792,3.229 0.115,0.156 10 false 2 1.708,0.885 1.823,1.042 0.115,0.156 10 false 1

Temporarily install the oil cooler to the radiator support.

NOTICE:

Securely attach the 2 claws of the oil cooler into the hole of the radiator support.



b.

Install the 4 bolts in the sequence shown in the illustration.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


Hide 32917 8.INSTALL TRANSMISSION OIL COOLER AIR DUCT (w/ Air Cooled Transmission Oil Cooler)

U164620E02
0.938,1.156 1.052,1.313 0.115,0.156 10 false 3 2.646,2.219 2.76,2.375 0.115,0.156 10 false 4 0.646,2.25 0.76,2.406 0.115,0.156 10 false 2 2.656,1.219 2.771,1.375 0.115,0.156 10 false 1

a.

Install the oil cooler air duct with the 4 bolts in the sequence shown in the illustration.

Torque:
4.9 N*m (50 kgf*cm, 43 in.*lbf)


Hide 88590 9.INSTALL SHROUD BLOWER ASSEMBLY (w/ Rear Air Conditioning System)

Hide 86520 10.INSTALL LOW PITCHED HORN ASSEMBLY

Hide 86510 11.INSTALL HIGH PITCHED HORN ASSEMBLY

Hide 88716A 12.CONNECT COOLER REFRIGERANT LIQUID PIPE A

E154817

a.

Remove the attached vinyl tape from the hose and the connecting part of the cooler condenser.


b.

Sufficiently apply compressor oil to a new O-ring and the fitting surface of the pipe joint.

Compressor oil:

ND-OIL 8 or equivalent



c.

Install O-ring on the liquid pipe A.


d.

Connect the liquid pipe A to the cooler condenser with the bolt.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)

NOTICE:
·

When tightening the bolt, do not allow any tools to contact the pipe.

·

When tightening the bolt, hold a part of the pipe near the connector.




Hide 88711 13.CONNECT NO. 1 COOLER REFRIGERANT DISCHARGE HOSE

E154818

a.

Remove the attached vinyl tape from the pipe and the connecting part of the cooler condenser.


b.

Sufficiently apply compressor oil to a new O-ring and the fitting surface of the hose joint.

Compressor oil:

ND-OIL 8 or equivalent



c.

Install O-ring on the discharge hose.


d.

Connect the discharge hose to the cooler condenser with the 2 bolts.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)

NOTICE:
·

When tightening the bolts, do not allow any tools to contact the pipe.

·

When tightening the bolts, hold a part of the pipe near the connector.




Hide 15.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 53292A 20.INSTALL UPPER RADIATOR SUPPORT SEAL