Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System) › from 2015.08
RM2660E _58 Vehicle Interior _052847 HEATING / AIR CONDITIONING _0255699 AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System) J

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)  Viscous Heater with Magnet Clutch Circuit  


DESCRIPTION

When the idle up switch is pushed, the air conditioning amplifier assembly turns on the viscous heater relay and operates the viscous heater. If the viscous heater does not operate when the idle up switch is pushed, there may be a problem in the circuit shown below.

WIRING DIAGRAM

w/ Rear Heater:


E337655E02
5.656,0.885 6.135,1.052 0.479,0.167 10 false SW 1 5.677,2.104 6.156,2.271 0.479,0.167 10 false MGCA 5.25,1 5.573,1.198 0.323,0.198 10 false E35 5.219,2.208 5.542,2.458 0.323,0.25 10 false E36 5.302,0.771 5.552,0.938 0.25,0.167 10 false 28 4.5,0.896 4.75,1.063 0.25,0.167 10 false 6 4.208,0.896 4.458,1.063 0.25,0.167 10 false +S 4.271,0.469 4.521,0.635 0.25,0.167 10 false E 2.844,0.458 3.219,0.625 0.375,0.167 10 false IND+ 2.667,0.448 2.833,0.615 0.167,0.167 10 false 2 1.719,0.708 2.604,0.875 0.885,0.167 10 false ECU-IG NO.2 1.198,2.458 2.083,2.625 0.885,0.167 10 false ENG-IG NO.1 3.177,1.344 3.688,1.552 0.51,0.208 10 false E97 3.188,1.51 4.24,1.677 1.052,0.167 10 false Idle Up Switch 0.427,0.552 1.385,0.917 0.958,0.365 10 false from IG1 NO.2 Relay 0.083,3.115 0.917,3.333 0.833,0.219 10 false from Battery 0.292,2.198 0.906,2.594 0.615,0.396 10 false from IG1 Relay 4.49,0.469 4.74,0.635 0.25,0.167 10 false 3 5.271,1.969 5.521,2.135 0.25,0.167 10 false 32 4.573,2.219 4.823,2.385 0.25,0.167 10 false 1Q 1.5,3.115 1.75,3.281 0.25,0.167 10 false 1Y 1.99,3.115 2.24,3.281 0.25,0.167 10 false 1K 1.99,2.198 2.24,2.365 0.25,0.167 10 false 1Q 1.479,2.896 1.729,3.063 0.25,0.167 10 false 1*1 1.958,2.885 2.208,3.052 0.25,0.167 10 false 1*2 2.031,1.958 2.281,2.125 0.25,0.167 10 false 3 4.625,1.99 4.875,2.156 0.25,0.167 10 false 1 4.615,2.875 4.865,3.042 0.25,0.167 10 false 2 4.563,3.115 4.813,3.281 0.25,0.167 10 false 1Q 4.188,4.052 4.542,4.219 0.354,0.167 10 false MG+ 4.604,4.063 4.958,4.229 0.354,0.167 10 false 1 2.448,4.979 2.802,5.146 0.354,0.167 10 false C98 0.198,4.917 1.448,5.083 1.25,0.167 10 false *1: for LHD 0.198,5.26 1.448,5.427 1.25,0.167 10 false *2: for RHD 5.51,2.958 7.094,3.333 1.583,0.375 10 false Air Conditioning Amplifier Assembly 2.458,5.167 5.365,5.427 2.906,0.26 10 false Viscous with Magnet Clutch Heater Assembly 2.958,4.542 4.542,4.76 1.583,0.219 10 false Magnet Clutch Assembly 3.438,3.427 4.146,3.594 0.708,0.167 10 false VICS HTR 2.396,3.646 4.417,3.844 2.021,0.198 10 false No. 1 Engine Room Relay Block 2.635,3.292 3.135,3.458 0.5,0.167 10 false P/HTR


w/o Rear Heater:


E337656E01
5.422,0.897 5.901,1.064 0.478,0.167 10 SW 1 5.422,2.119 5.901,2.286 0.478,0.167 10 MGCA 5.187,2.897 5.665,3.064 0.478,0.167 10 E81 5.184,0.896 5.434,1.063 0.249,0.167 10 4 4.472,0.904 4.722,1.071 0.249,0.167 10 6 4.175,0.904 4.425,1.071 0.249,0.167 10 +S 4.256,0.448 4.506,0.615 0.249,0.167 10 E 2.834,0.448 3.210,0.615 0.376,0.167 10 IND+ 2.649,0.448 2.820,0.615 0.171,0.167 10 2 1.642,0.676 2.528,0.843 0.886,0.167 10 ECU-IG NO.2 0.356,0.531 1.310,0.998 0.954,0.467 10 from IG1 NO.2 Relay 4.479,0.448 4.729,0.615 0.249,0.167 10 3 5.13,2.118 5.380,2.285 0.249,0.167 10 17 4.57,2.193 4.819,2.360 0.249,0.167 10 1Q 4.634,1.971 4.884,2.138 0.249,0.167 10 1 4.634,2.9 4.884,3.067 0.249,0.167 10 2 4.57,3.106 4.819,3.273 0.249,0.167 10 1Q 4.167,4.079 4.517,4.246 0.350,0.167 10 MG+ 4.591,4.079 4.941,4.246 0.350,0.167 10 1 2.334,5.011 2.684,5.178 0.350,0.167 10 C98 0.125,5.12 1.379,5.287 1.253,0.167 10 *1: for LHD 0.125,5.459 1.379,5.626 1.253,0.167 10 *2: for RHD 5.187,3.069 6.799,3.449 1.612,0.380 10 Air Conditioning Amplifier Assembly 2.334,5.148 5.257,5.315 2.924,0.167 10 Viscous with Magnet Clutch Heater Assembly 2.402,3.639 4.418,3.837 2.017,0.198 10 No. 1 Engine Room Relay Block 2.971,4.518 4.550,4.685 1.579,0.167 10 Magnet Clutch Assembly 3.111,1.323 3.997,1.490 0.886,0.167 10 E97 3.111,1.46 4.163,1.627 1.052,0.167 10 Idle Up Switch 1.17,2.434 2.056,2.601 0.886,0.167 10 ENG-IG NO.1 0.076,3.102 1.030,3.319 0.954,0.216 10 from Battery 0.282,2.201 0.895,2.675 0.613,0.474 10 from IG1 Relay 1.506,3.112 1.755,3.280 0.249,0.167 10 1Y 1.973,3.112 2.223,3.280 0.249,0.167 10 1K 1.973,2.201 2.223,2.368 0.249,0.167 10 1Q 1.506,2.891 1.755,3.058 0.249,0.167 10 1*1 1.973,2.891 2.223,3.058 0.249,0.167 10 1*2 2.047,1.95 2.296,2.117 0.249,0.167 10 3 3.415,3.422 4.121,3.589 0.706,0.167 10 VICS HTR 2.609,3.258 3.111,3.425 0.503,0.167 10 P/HTR


PROCEDURE

1.READ VALUE USING GTS (IDLE UP/PWR HEATER SWITCH)
a.

Use the Data List to check if the idle up switch is functioning properly (See page Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System)>DATA LIST / ACTIVE TEST).

Air Conditioner
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
IDLE UP/PWR HEAT Switch Idle up switch / ON or OFF ON: Idle up switch on
OFF: Idle up switch off
-

OK:

The display is as specified in the normal condition column.




OK

2.PERFORM ACTIVE TEST USING GTS (VISCOUS HEATER)

NG

3.CHECK HARNESS AND CONNECTOR (IDLE UP SWITCH - BATTERY AND BODY GROUND)
2.PERFORM ACTIVE TEST USING GTS (VISCOUS HEATER)
a.

Select the Active Test, use the GTS to generate a control command, and then check that the viscous heater relay (VICS HTR) (See page Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System)>DATA LIST / ACTIVE TEST).

Tester Display Test Part Control Range Diagnostic Note
Viscous Heater Viscous heater relay ON / OFF -

OK:

Viscous heater relay operates using GTS.




OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

6.INSPECT VISCOUS HEATER RELAY (VICS HTR RELAY)
3.CHECK HARNESS AND CONNECTOR (IDLE UP SWITCH - BATTERY AND BODY GROUND)
a.
U166617E01
1.574,0.208 1.927,0.374 0.354,0.167 10 E97 0.036,0 0.390,0.167 0.354,0.167 10 *a 0.469,1.695 0.822,1.862 0.354,0.167 10 IND+ 1.937,1.695 2.291,1.862 0.354,0.167 10 E 1.296,1.381 1.152,1.799 1.152,1.799 0.884,1.799 false 1.479,1.381 1.623,1.799 1.623,1.799 1.891,1.799 false

Disconnect the idle up switch assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E97-3 (E) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
E97-2 (IND+) - Body ground Ignition switch off Below 1 V
E97-2 (IND+) - Body ground Ignition switch ON 11 to 14 V



Text in Illustration
*a Front view of wire harness connector
(to Idle Up Switch)


OK

4.INSPECT IDLE UP SWITCH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT IDLE UP SWITCH

OK

5.CHECK HARNESS AND CONNECTOR (IDLE UP SWITCH - AIR CONDITIONING AMPLIFIER ASSEMBLY)

NG

5.CHECK HARNESS AND CONNECTOR (IDLE UP SWITCH - AIR CONDITIONING AMPLIFIER ASSEMBLY)
a.

w/ Rear Heater:

i.

Disconnect the E35 air conditioning amplifier assembly connector.


ii.

Disconnect the E97 idle up switch connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E35-28 (SW 1) - E97-6 (+S) Always Below 1 Ω
E35-28 (SW 1) or E97-6 (+S) - Body ground Always 10 kΩ or higher




b.

w/o Rear Heater:

i.

Disconnect the E81 air conditioning amplifier assembly connector.


ii.

Disconnect the E97 idle up switch connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E81-4 (SW 1) - E97-6 (+S) Always Below 1 Ω
E81-4 (SW 1) or E97-6 (+S) - Body ground Always 10 kΩ or higher





OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT VISCOUS HEATER RELAY (VICS HTR RELAY)
a.

Remove the viscous heater relay (VICS HTR) from the No. 1 engine room relay block.


b.


OK

7.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY - BATTERY)

NG

REPLACE VISCOUS HEATER RELAY

7.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY - BATTERY)
a.
U166514E01
0.054,0.006 0.274,0.177 0.220,0.171 10 *a 0.731,1.894 1.184,2.065 0.453,0.171 10 MGCA 0.593,1.178 0.970,1.348 0.377,0.171 10 E36 1.27,1.974 1.498,1.974 1.498,1.974 1.667,1.526 false

w/ Rear Heater:

i.

Disconnect the air conditioning amplifier assembly connector.


ii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
E36-32 (MGCA) - Body ground Ignition switch off Below 1 V
E36-32 (MGCA) - Body ground Ignition switch ON 11 to 14 V




b.
U166422E01
1.562,0.285 1.986,0.537 0.424,0.253 10 E81 0.043,0.027 0.467,0.280 0.424,0.253 10 *a 0.02,0.475 0.487,0.652 0.467,0.177 10 MGCA 0.577,0.555 0.853,0.555 0.853,0.555 1.073,1.283 false

w/o Rear Heater:

i.

Disconnect the air conditioning amplifier assembly connector.


ii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
E81-17 (MGCA) - Body ground Ignition switch off Below 1 V
E81-17 (MGCA) - Body ground Ignition switch ON 11 to 14 V




Text in Illustration
*a Rear view of wire harness connector
(to Air Conditioning Amplifier Assembly)


OK

8.CHECK HARNESS AND CONNECTOR (VISCOUS HEATER RELAY - VISCOUS WITH MAGNET CLUTCH HEATER ASSEMBLY AND BATTERY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (VISCOUS HEATER RELAY - VISCOUS WITH MAGNET CLUTCH HEATER ASSEMBLY AND BATTERY)

*1: for LHD

*2: for RHD


a.

Disconnect the 1Q, 1Y*1 or 1K*2 No. 1 engine room relay block connector.


b.

Disconnect the C98 viscous with magnet clutch heater assembly connector


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1Q-2 - C98- (MG+) Always Below 1 Ω
1Q-2 or C98- (MG+ - Body ground Always 10 kΩ or higher


i.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for LHD:
Tester Connection Condition Specified Condition
1Y-1 - Body ground Always 11 to 14 V
1Q-3 - Body ground Ignition switch off Below 1 V
1Q-3 - Body ground Ignition switch ON 11 to 14 V

for RHD:
Tester Connection Condition Specified Condition
1K-1 - Body ground Always 11 to 14 V
1Q-3 - Body ground Ignition switch off Below 1 V
1Q-3 - Body ground Ignition switch ON 11 to 14 V





OK

9.CHECK VISCOUS WITH MAGNET CLUTCH HEATER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK VISCOUS WITH MAGNET CLUTCH HEATER ASSEMBLY
a.

Replace the viscous with magnet clutch heater assembly with a new or known good one (See page Vehicle Interior>HEATING / AIR CONDITIONING>HEATER WATER PUMP (w/ Viscous Heater)>REMOVAL).


b.

Check that the air conditioning system is operated normally.

OK:

Air conditioning system is operated normally.




OK

END (VISCOUS WITH MAGNET CLUTCH HEATER ASSEMBLY WAS DEFECTIVE)

NG

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY