Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM(for Manual Air Conditioning System) › from 2015.08
RM2660E _58 Vehicle Interior _052847 HEATING / AIR CONDITIONING _0255703 AIR CONDITIONING SYSTEM(for Manual Air Conditioning System) C

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Manual Air Conditioning System)  B1413/13  Evaporator Temperature Sensor Circuit  


DESCRIPTION

The No. 1 cooler thermistor (evaporator temperature sensor) is installed on the evaporator in the air conditioner unit to detect the cooled air temperature that has passed through the evaporator and control the air conditioning. It sends appropriate signals to the air conditioning amplifier assembly. The resistance of the No. 1 cooler thermistor (evaporator temperature sensor) changes in accordance with the cooled air temperature that has passed through the evaporator. As the temperature decreases, the resistance increases. As the temperature increases, the resistance decreases.

The air conditioning amplifier assembly applies voltage (5 V) to the No. 1 cooler thermistor (evaporator temperature sensor) and reads voltage changes as the resistance of the No. 1 cooler thermistor (evaporator temperature sensor) changes. This sensor is used for frost prevention.

DTC Code DTC Detection Condition Trouble Area
B1413/13 An open or short in the No. 1 cooler thermistor (evaporator temperature sensor) circuit.
·

No. 1 cooler thermistor (evaporator temperature sensor)

·

Air conditioning harness assembly (No. 1 cooler thermistor)

·

Air conditioning amplifier assembly



WIRING DIAGRAM

E316646E20
4.833,1.615 5.146,1.813 0.313,0.198 10 false z71 4.833,1.792 7.104,2.031 2.271,0.24 10 false Air Conditioning Amplifier Assembly 6.167,0.635 6.479,0.833 0.313,0.198 10 false AD 5.719,0.219 6.031,0.417 0.313,0.198 10 false 5 V 4.792,0.521 5.104,0.719 0.313,0.198 10 false TE 4.75,1.01 5.219,1.208 0.469,0.198 10 false SG 4.573,0.521 4.885,0.719 0.313,0.198 10 false 6 4.573,1.01 5.042,1.208 0.469,0.198 10 false 5 3.104,1.385 4.635,1.771 1.531,0.385 10 false Air Conditioning Harness Assembly 3,0.521 3.313,0.719 0.313,0.198 10 false 2 3.01,1 3.323,1.198 0.313,0.198 10 false 1 0.75,1.521 2.969,1.969 2.219,0.448 10 false No. 1 Cooler Thermistor (Evaporator Temperature Sensor)

PROCEDURE

1.READ VALUE USING GTS (EVAPORATOR FIN THERMISTOR)
a.

Use the Data List to check if the No. 1 cooler thermistor (evaporator temperature sensor) is functioning properly (See page Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System)>DATA LIST / ACTIVE TEST)

Air Conditioner
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Evaporator Fin Thermistor No. 1 cooler thermistor / Min.: -29.7°C (-21.46°F), Max.: 59.55°C (139.19°F) Actual evaporator temperature displayed No. 1 cooler thermistor (evaporator temperature sensor) system malfunction:
·

Open in the circuit: -29.7°C (-21.46°F)

·

Short in the circuit: 59.55°C (139.19°F)



OK:

The display is as specified in the normal condition.


Result
Result Proceed to
OK (When troubleshooting according to the DTC) A
OK (When troubleshooting according to Problem Symptoms Table) B
NG C



A

B

C

2.INSPECT NO. 1 COOLER THERMISTOR (EVAPORATOR TEMPERATURE SENSOR)
2.INSPECT NO. 1 COOLER THERMISTOR (EVAPORATOR TEMPERATURE SENSOR)

A

3.CHECK AIR CONDITIONING HARNESS ASSEMBLY

B

REPLACE NO. 1 COOLER THERMISTOR (EVAPORATOR TEMPERATURE SENSOR)

C

REPLACE NO. 1 COOLER THERMISTOR (EVAPORATOR TEMPERATURE SENSOR)

3.CHECK AIR CONDITIONING HARNESS ASSEMBLY
a.
U166593E03
2.177,2.583 1.927,2.865 1.927,2.865 1.635,2.865 false 2.313,2.604 2.188,3.104 2.188,3.104 1.896,3.104 false 0.115,0.604 0.479,0.823 0.365,0.219 10 false *a 1.438,1.115 1.802,1.333 0.365,0.219 10 false *b 1.854,0.094 2.219,0.313 0.365,0.219 10 false *c 1.854,1.469 2.219,1.688 0.365,0.219 10 false *d 1.385,2.76 1.75,2.979 0.365,0.219 10 false SG 1.479,2.219 1.844,2.438 0.365,0.219 10 false z71 1.677,3.01 2.042,3.229 0.365,0.219 10 false TE

Remove the air conditioning harness assembly.



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - z71-5 (SG) Always Below 1 Ω
2 - z71-6 (TE) Always Below 1 Ω
1 - 2 Always 10 kΩ or higher
1 or z71-5 (SG) - Body ground Always 10 kΩ or higher
2 or z71-6 (TE) - Body ground Always 10 kΩ or higher



Text in Illustration
*a Air Conditioning Harness Assembly
*b to No. 1 Cooler Thermistor (Evaporator Temperature Sensor) Connector
*c Front view of air conditioning harness assembly
(to No. 1 Cooler Thermistor [Evaporator Temperature Sensor])
*d Front view of air conditioning harness assembly
(to Air Conditioning Amplifier Assembly)

Result
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C


A

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

B

C