Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM(for Models with Jam Protection Function on 4 Windows) › 2014.08–2015.08
RM2660E _59 Vehicle Exterior _052850 WINDOW / GLASS _0255725 POWER WINDOW CONTROL SYSTEM(for Models with Jam Protection Function on 4 Windows) J

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM(for Models with Jam Protection Function on 4 Windows)  Rear Power Window RH Auto Up / Down Function does not Operate with Rear Power Window Switch RH  


DESCRIPTION

If the auto up/down function does not operate, the cause may be one or more of the following:


·

The ECU in the power window regulator motor determines that the power window regulator motor has not been initialized.

·

The power window regulator switch has a malfunction.

·

The Hall-IC in the power window regulator motor has a malfunction.

·

There is an open or short in the wiring between the rear power window regulator switch RH and the power window regulator motor.


WIRING DIAGRAM

E275629E06
1.26,0.865 1.729,1.063 0.469,0.198 10 false AUTO 1.76,0.75 2.01,0.99 0.25,0.24 10 false 8 5.458,0.875 5.927,1.073 0.469,0.198 10 false AUTO 5.01,1.708 5.823,1.906 0.813,0.198 10 false J4 5.01,1.885 6.979,2.313 1.969,0.427 10 false Rear Power Window Regulator Motor Assembly RH 0.344,1.708 0.625,1.927 0.281,0.219 10 false J3 0.344,1.875 2.354,2.302 2.01,0.427 10 false Rear Power Window Regulator Switch Assembly RH 5.25,0.74 5.396,0.938 0.146,0.198 10 false 4

PROCEDURE

1.CHECK FOR DTC
a.

Check for DTCs (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM(for Models with Jam Protection Function on 4 Windows)>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC is not output A
B2311 is output B
B2312 is output C
B2313 is output D
LIN communication system DTCs are output E



A

2.CHECK MANUAL UP/DOWN FUNCTION (REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH)

B

C

D

E

2.CHECK MANUAL UP/DOWN FUNCTION (REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH)
a.

Check that the manual up/down function using the rear power window regulator switch RH can operate the rear door power window RH (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM(for Models with Jam Protection Function on 4 Windows)>OPERATION CHECK).

OK:

Manual up/down function operates.




OK

3.READ VALUE USING INTELLIGENT TESTER (REAR POWER WINDOW REGULATOR MOTOR RH)

NG

3.READ VALUE USING INTELLIGENT TESTER (REAR POWER WINDOW REGULATOR MOTOR RH)
a.

Use the Data List to check if the power window regulator motor is functioning properly (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM(for Models with Jam Protection Function on 4 Windows)>DATA LIST / ACTIVE TEST).

RR-Door Motor
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
RR Door P/W Auto SW Rear power window RH auto up/down signal / ON or OFF ON: Rear power window RH auto up/down switch operated
OFF: Rear power window RH switch not operated
-

OK:

The display changes according to operation of the rear power window switch RH.




OK

REPLACE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

NG

4.CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY RH - REAR POWER WINDOW REGULATOR MOTOR RH)
4.CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY RH - REAR POWER WINDOW REGULATOR MOTOR RH)
a.
U164019E02
1.99,1.729 2.406,1.563 false 1.219,3.656 1.594,3.854 false 0.323,2.135 2.615,2.521 2.292,0.385 10 false Front view of wire harness connector: (to Power Window Regulator Motor) 0.25,0.104 2.563,0.479 2.313,0.375 10 false Front view of wire harness connector: (to Power Window Regulator Switch) 0.656,1.104 0.833,1.292 0.177,0.188 10 false J3 0.688,3.271 0.865,3.458 0.177,0.188 10 false J4 2.469,1.479 2.885,1.646 0.417,0.167 10 false AUTO 0.781,3.563 1.198,3.729 0.417,0.167 10 false AUTO

Disconnect the J3 switch connector.


b.

Disconnect the J4 motor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J3-8 (AUTO) - J4-4 (AUTO) Always Below 1 Ω
J3-8 (AUTO) or J4-4 (AUTO) - Body ground Always 10 kΩ or higher




OK

5.INSPECT REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY RH
U164024E02
2.021,2.625 2.406,2.479 false 1.333,2.979 0.865,3.198 false 0.073,1.417 2.792,1.813 2.719,0.396 10 false Component without harness connected: (Rear Power Window Regulator Switch RH) 0.531,2.229 0.708,2.417 0.177,0.188 10 false J3 0.417,3.135 0.844,3.302 0.427,0.167 10 false AUTO 2.49,2.375 2.844,2.542 0.354,0.167 10 false GND

a.

Remove the rear power window regulator switch (See page Vehicle Exterior>WINDOW / GLASS>REAR POWER WINDOW SWITCH>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
J3-8 (AUTO) - J3-1 (GND) Auto up/down operation Below 1 Ω




OK

REPLACE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

NG

REPLACE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY RH