Home › Vehicle Exterior › DOOR / HATCH › REAR DOOR › from 2015.08
RM2660E _59 Vehicle Exterior _052852 DOOR / HATCH _0255748 REAR DOOR A

DOOR / HATCH  REAR DOOR  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The procedure listed below is for the LH side.

·

A bolt without a torque specification is shown in the standard bolt chart (See page General>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS).



PROCEDURE

Hide 67872 1.INSTALL REAR DOOR WEATHERSTRIP LH

HINT:

When installing the rear door weatherstrip, heat the vehicle body and rear door weatherstrip using a heat light.


Standard:
Item Temperature
Vehicle Body 40 to 60°C (104 to 140°F)
Rear Door Weatherstrip 20 to 30°C (68 to 86°F)


NOTICE:

Do not heat the vehicle body or rear door weatherstrip excessively.


a.

w/ Spot Cover:

i.

Using a heat light, heat the vehicle body surface.


ii.

Remove the double-sided tape from the vehicle body.


iii.

Wipe off any tape adhesive residue with cleaner.


iv.

Using a heat light, heat the vehicle body and a new rear door weatherstrip LH.


v.

Remove the peeling paper from the face of the rear door weatherstrip LH.

HINT:

After removing the peeling paper, keep the exposed adhesive free from foreign matter.



vi.

Attach the 21 clips to install a new rear door weatherstrip LH.

HINT:
·

If clips are damaged during installation, replace them.

·

Press the rear door weatherstrip LH firmly to install it.





b.

w/o Spot Cover:

i.

Attach the 21 clips to install the rear door weatherstrip LH.

HINT:

If clips are damaged during installation, replace them.




Hide 68640A 2.INSTALL REAR DOOR CHECK ASSEMBLY LH

a.

Install the rear door check assembly LH to the door panel with the 2 nuts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


b.

Apply adhesive to the threads of the bolt.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



c.

Install the bolt.

Torque:
27 N*m (275 kgf*cm, 20 ft.*lbf)


Hide 89746F 3.INSTALL NO. 4 ELECTRICAL KEY WIRE HARNESS (w/ Entry and Start System)

a.

Connect the connector.


b.

Attach the 2 clamps to install the No. 4 electrical key wire harness to the rear door outside handle frame sub-assembly LH.


Hide 69204A 4.INSTALL REAR DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY LH

a.
B436174E07
0.385,2.167 0.385,1.542 0.385,1.542 0.594,1.542 false 0.406,2.521 0.406,3.115 0.406,3.115 0.573,3.115 false 2.135,2.469 2.135,3.073 2.135,3.073 1.958,3.073 false 0.594,1.438 0.792,1.688 0.198,0.25 10 true *b 0.583,3.01 0.74,3.188 0.156,0.177 10 false *b 1.75,2.969 1.948,3.219 0.198,0.25 10 true *a

Attach the nut and 2 guides to install the rear door outside handle frame sub-assembly LH.

Text in Illustration
*a Nut
*b Guide


b.

Using a T30 "TORX" wrench, install the rear door outside handle frame sub-assembly LH with the screw.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


c.

w/ Entry and Start System:

i.

Attach the clamp.



Hide 69254B 5.INSTALL REAR DOOR NO. 2 OUTSIDE HANDLE PAD LH

a.

Attach the 2 claws to install the rear door No. 2 outside handle pad LH.


Hide 69252B 6.INSTALL REAR DOOR NO. 1 OUTSIDE HANDLE PAD LH

a.

Attach the 3 claws to install the rear door No. 1 outside handle pad LH.


Hide 69240 7.INSTALL REAR DOOR OUTSIDE HANDLE ASSEMBLY LH

a.
B436175

Install the rear door outside handle assembly LH.


b.

Attach the 2 claws and connect the holder.


c.

w/ Entry and Start System:

i.

Connect the connector.


ii.
B436176

Attach the 3 claws to install the connector and connector cover.



Hide 69227L 8.INSTALL REAR DOOR OUTSIDE HANDLE COVER LH

a.

Attach the claw to install the rear door outside handle cover LH.


b.

Using a T30 ''TORX'' socket, install the rear door outside handle cover LH with the "TORX" screw.


Hide 69780B 9.INSTALL REAR DOOR INSIDE LOCKING CABLE ASSEMBLY LH

a.
B188530E03
0.135,2.426 0.392,2.624 0.257,0.198 10 *B 0.135,0.103 0.392,0.301 0.257,0.198 10 *A

Install the rear door inside locking cable assembly LH.

Text in Illustration
*A w/o Double Lock
*B w/ Double Lock


b.
B183929

Attach the 3 claws.


Hide 69740D 10.INSTALL REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY LH

a.

Install the rear door lock remote control cable assembly LH.


b.
B183928

Attach the claw.


Hide 69340 11.INSTALL REAR DOOR LOCK ASSEMBLY LH

Hide 67836H 12.INSTALL REAR DOOR LOCK CHILD PROTECTION COVER LH

Hide 75762A 13.INSTALL REAR DOOR FRONT WINDOW FRAME MOULDING LH

Hide 75740 14.INSTALL REAR DOOR BELT MOULDING ASSEMBLY LH

Hide 85720G 15.INSTALL REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

Hide 69804 16.INSTALL REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY LH

a.
B436164E07
2.469,0.646 2.74,0.406 false 2.729,0.281 2.958,0.531 0.229,0.25 10 true *a 0.802,0.625 1,0.813 0.198,0.188 10 true (4) 1.063,1.635 1.24,1.833 0.177,0.198 10 true (1) 2.594,0.563 2.823,0.75 0.229,0.188 10 true (2) 2.635,1.573 2.865,1.76 0.229,0.188 10 true (3)

Apply MP grease to the sliding parts of the rear door window regulator sub-assembly LH.

Text in Illustration
*a Temporary Bolt


b.

Loosely install the temporary bolt onto the rear door window regulator sub-assembly LH.


c.

Insert the rear door window regulator sub-assembly LH into the door panel. Use the temporary bolt to hang the rear door window regulator sub-assembly LH on the door panel.

NOTICE:

Be careful not to drop the rear door window regulator sub-assembly LH as it may become damaged.



d.

Temporarily install the rear door window regulator sub-assembly LH with the 3 bolts.


e.

Tighten the 4 bolts in the order shown in the illustration.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 67676C 17.INSTALL REAR DOOR NO. 2 FRAME GARNISH LH

a.

Attach a new clip to install the rear door No. 2 frame garnish LH.


Hide 67674A 18.INSTALL REAR DOOR FRAME GARNISH LH

a.

Attach a new clip to install the rear door frame garnish LH.


Hide 69975A 19.INSTALL REAR DOOR GLASS CHANNEL FILLER (for Tempered Glass)

a.
B235661E02
0.92,0.407 1.117,0.586 0.198,0.179 10 *a 0.765,0.727 0.963,0.907 0.198,0.179 10 *b

Install the rear door glass channel filler onto the rear door glass.

Text in Illustration
*a Front Side
*b 8.0 mm (0.327 in.)


Hide 69906B 20.INSTALL REAR DOOR GLASS CHANNEL SUB-ASSEMBLY LH (for Tempered Glass)

a.

Apply soapy water to the inside of the rear door glass channel sub-assembly LH.


b.
B235662E02
0.914,0.427 1.113,0.603 0.199,0.176 10 *a 0.767,0.774 0.971,0.937 0.204,0.163 10 *b

Using a plastic-faced hammer, tap the channel onto the glass to install the rear door glass channel sub-assembly LH.

NOTICE:

Be careful not to damage the glass or rear door glass channel sub-assembly LH.


Text in Illustration
*a Front Side
*b 8.0 mm (0.327 in.)


Hide 68104 21.INSTALL REAR DOOR GLASS SUB-ASSEMBLY LH

a.
B180922

Slide the rear door glass sub-assembly LH as shown in the illustration to install it.


Hide 68189 22.INSTALL REAR DOOR QUARTER WINDOW WEATHERSTRIP LH

a.

Install the rear door quarter window glass LH to the rear door quarter window weatherstrip LH.


Hide 68124C 23.INSTALL REAR DOOR QUARTER WINDOW GLASS LH

a.
B183926

Install the rear door quarter window glass LH together with the rear door quarter window weatherstrip LH in the direction indicated by the arrow in the illustration.


Hide 67408F 24.INSTALL REAR DOOR REAR LOWER WINDOW FRAME SUB-ASSEMBLY LH

a.

Install the rear door rear lower window frame sub-assembly LH with the 2 bolts and screw.


Hide 68152C 25.INSTALL REAR DOOR GLASS RUN LH

a.

Install the rear door glass run LH.


Hide 67858B 26.INSTALL REAR DOOR PANEL PROTECTOR LH

a.

Attach the claw to install the rear door panel protector LH.


Hide 67842E 27.INSTALL REAR DOOR SERVICE HOLE COVER LH

a.

Apply butyl tape to the door.


b.
B180918

Pass the rear door lock remote control cable assembly LH and rear door inside locking cable assembly LH through a new rear door service hole cover LH.

NOTICE:
·

When installing the rear door service hole cover LH, pull the links and connectors through the rear door service hole cover LH.

·

There should be no wrinkles or folds after attaching the rear door service hole cover LH.

·

After attaching the rear door service hole cover LH, check the sealing quality.




c.
B436163

Connect the 3connectors.


d.

Attach the 7clamps.


e.
B180916E03
2.521,1.75 2.781,1.99 0.26,0.24 10 false 45° 3.083,1.74 3.354,1.979 0.271,0.24 10 false 45°

Install the bolt as shown in the illustration.

Torque:
8.4 N*m (86 kgf*cm, 74 in.*lbf)


Hide 86160C 28.INSTALL REAR SPEAKER SET (w/ Rear Speaker)

Hide 86160Z 29.INSTALL REAR NO. 3 SPEAKER ASSEMBLY (for 14 Speakers)

Hide 69288A 30.INSTALL REAR DOOR INSIDE HANDLE BEZEL LH

a.

Install the rear door inside handle bezel LH to the trim board with the 6 screws.


Hide 69206C 31.INSTALL REAR DOOR INSIDE HANDLE SUB-ASSEMBLY LH

a.

Attach the 2 claws to install the rear door inside handle sub-assembly LH.


Hide 82508 32.INSTALL REAR DOOR WIRING SUB-ASSEMBLY LH (w/ Illumination)

a.

Attach the clamp to install the connector.


b.

Connect the connector.


Hide 68174A 33.INSTALL REAR DOOR INNER GLASS WEATHERSTRIP LH

a.
U155772

Install the rear door inner glass weatherstrip LH to the door panel.


Hide 67604 34.INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY LH

a.

Connect the connector.


b.
B183925

Connect the rear door lock remote control cable assembly LH and rear door inside locking cable assembly LH to the rear door inside handle sub-assembly LH.


c.
B436178

Attach the 4 claws and pin.


d.

Attach the 9 clips to install the rear door trim board sub-assembly LH.


e.

Install the 3 screws.


Hide 74611C 35.INSTALL ASSIST GRIP COVER LH

a.

Attach the 9 claws to install the assist grip cover LH to the rear door trim board sub-assembly LH.


Hide 84810D 36.INSTALL REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY

Hide 74272A 37.INSTALL REAR DOOR UPPER ARMREST BASE PANEL LH

Hide 69278C 38.INSTALL REAR DOOR INSIDE HANDLE BEZEL LH

a.

Attach the 4 claws to install the rear door inside handle bezel LH.


Hide 81230 39.INSTALL COURTESY LIGHT ASSEMBLY (w/ Courtesy Light)

Hide 75076 40.INSTALL REAR DOOR OUTSIDE MOULDING SUB-ASSEMBLY LH (w/ Outside Moulding)

Hide 41.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).