ECM sends the reverse signal to the outer mirror control ECU assembly LH and RH via CAN communication. Each outer mirror control ECU assembly then performs control in response to the reverse signal.
The reverse shift-linked function will not occur when the mirror master switch is in the neutral position (off).
First perform the communication function inspections in How to Proceed with Troubleshooting to confirm that there are no CAN communication malfunctions before troubleshooting this problem (See page Vehicle Exterior>MIRROR (EXT)>POWER MIRROR CONTROL SYSTEM(w/ Retract Mirror)>HOW TO PROCEED WITH TROUBLESHOOTING).
If the main body ECU (multiplex network body ECU) is replaced, refer to the Entry and Start System (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Entry Function)>PRECAUTION).
Check that the memory and reactivation function operates (See page Vehicle Exterior>MIRROR (EXT)>POWER MIRROR CONTROL SYSTEM(w/ Retract Mirror)>OPERATION CHECK).
Memory and reactivation function operates normally.
OK
NG
Check for DTCs.
for 1UR-FE: See page Engine / Hybrid System>1UR-FE (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR
for 1GR-FE: See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR
for 1VD-FTV (w/ DPF): See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>DTC CHECK / CLEAR
for 1VD-FTV (w/o DPF): See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>DTC CHECK / CLEAR
DTCs output does not occur.
for 1VD-FTV (w/ DPF): See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>DIAGNOSTIC TROUBLE CODE CHART
for 1VD-FTV (w/o DPF): See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>DIAGNOSTIC TROUBLE CODE CHART
A
B
C
Check that the shift indicator of the combination meter operates normally.
Shift indicator of combination meter operates normally.
OK
NG
(See pageVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING)
Check the malfunctioning outer rear view mirror assembly (See page Vehicle Exterior>MIRROR (EXT)>POWER MIRROR CONTROL SYSTEM(w/ Retract Mirror)>OPERATION CHECK).
| Result | Proceed to |
|---|---|
| Both left and right outer rear view mirror assembly do not operate (for LHD) | A |
| Both left and right outer rear view mirror assembly do not operate (for RHD) | B |
| Outer rear view mirror assembly LH does not operate | C |
| Outer rear view mirror assembly RH does not operate | D |
A
B
C
D
Replace the outer rear view mirror assembly LH with a new or known good one (See page Vehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR>REMOVAL).
NEXT
Check that the reverse shift-linked function operates (See page Vehicle Exterior>MIRROR (EXT)>POWER MIRROR CONTROL SYSTEM(w/ Retract Mirror)>OPERATION CHECK).
Reverse shift-linked function operates normally.
OK
NG
Replace the outer rear view mirror assembly LH with a new or known good one (See page Vehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR>REMOVAL).
NEXT
Check that the reverse shift-linked function operates (See page Vehicle Exterior>MIRROR (EXT)>POWER MIRROR CONTROL SYSTEM(w/ Retract Mirror)>OPERATION CHECK).
Reverse shift-linked function operates normally.
OK
NG