Home › Vehicle Exterior › MIRROR (EXT) › POWER MIRROR CONTROL SYSTEM(w/ Retract Mirror) › from 2015.08
RM2660E _59 Vehicle Exterior _052853 MIRROR (EXT) _0255766 POWER MIRROR CONTROL SYSTEM(w/ Retract Mirror) J

MIRROR (EXT)  POWER MIRROR CONTROL SYSTEM(w/ Retract Mirror)  Power Mirror cannot be Adjusted with Power Mirror Switch  


DESCRIPTION

When the outer mirror switch assembly mirror select switch is operated, right/left selection signals are sent to the main body ECU (multiplex network body ECU). The main body ECU (multiplex network body ECU) sends the received right/left selection signals to the outer mirror control ECU assemblies via CAN communication.

WIRING DIAGRAM

E325700E04
4.906,3.906 5.323,4.063 0.417,0.156 10 false E137 5.948,0.51 6.365,0.667 0.417,0.156 10 false 12 V 5.115,0.833 5.531,1.01 0.417,0.177 10 false MIRB 0.646,1.646 1.604,2.01 0.958,0.365 10 false Mirror Surface Adjust Switch 0.646,2.583 1.531,2.948 0.885,0.365 10 false Mirror Select Switch 4.865,0.854 5.031,1.031 0.167,0.177 10 false 4 5.115,2.271 5.531,2.448 0.417,0.177 10 false MIRS 4.865,2.302 5.031,2.479 0.167,0.177 10 false 5 5.115,2.99 5.531,3.167 0.417,0.177 10 false MIRE 4.021,0.844 4.354,1.021 0.333,0.177 10 false M+ 3.875,2.313 4.292,2.49 0.417,0.177 10 false MSW 4.104,3 4.271,3.177 0.167,0.177 10 false E 4.865,2.99 5.031,3.167 0.167,0.177 10 false 6 4.396,0.854 4.625,1.031 0.229,0.177 10 false 16 4.417,2.292 4.646,2.469 0.229,0.177 10 false 13 4.396,2.99 4.625,3.167 0.229,0.177 10 false 14 4.906,4.073 6.604,4.427 1.698,0.354 10 false Main Body ECU (Multiplex Network Body ECU) 1.51,3.792 1.927,3.948 0.417,0.156 10 false G19 1.5,3.938 3.51,4.188 2.01,0.25 10 false Outer Mirror Switch Assembly 0.719,7.281 2.729,7.531 2.01,0.25 10 false : CAN Communication Line 2.656,5.635 5.24,5.885 2.583,0.25 10 false Outer Mirror Control ECU Assembly LH 2.677,7.083 5.229,7.333 2.552,0.25 10 false Outer Mirror Control ECU Assembly RH

CAUTION / NOTICE / HINT

NOTICE:
·

First perform the communication function inspections in How to Proceed with Troubleshooting to confirm that there are no CAN communication malfunctions before troubleshooting this problem (See page Vehicle Exterior>MIRROR (EXT)>POWER MIRROR CONTROL SYSTEM(w/ Retract Mirror)>HOW TO PROCEED WITH TROUBLESHOOTING).

·

If the main body ECU (multiplex network body ECU) is replaced, refer to the Entry and Start System (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Entry Function)>PRECAUTION).



PROCEDURE

1.READ VALUE USING GTS (POWER MIRROR SWITCH)
a.

Using the GTS, read the Data List. (See page Vehicle Exterior>MIRROR (EXT)>POWER MIRROR CONTROL SYSTEM(w/ Retract Mirror)>DATA LIST / ACTIVE TEST).

Main Body
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Mirror Selection SW (R) Mirror select switch signal for RH mirror / ON or OFF ON: Mirror select switch is R position
OFF: Mirror select switch is except R position
-
Mirror Selection SW (L) Mirror select switch signal for LH mirror / ON or OFF ON: Mirror select switch is L position
OFF: Mirror select switch is except L position
-
Mirror Position SW (R) Mirror surface adjust switch signal (Right) / ON or OFF ON: Mirror surface adjust switch pressed right
OFF: Mirror surface adjust switch not pressed right
-
Mirror Position SW (L) Mirror surface adjust switch signal (Left) / ON or OFF ON: Mirror surface adjust switch not pressed left
OFF: Mirror surface adjust switch pressed left
-
Mirror Position SW (Up) Mirror surface adjust switch signal (Up) / ON or OFF ON: Mirror surface adjust switch pressed up
OFF: Mirror surface adjust switch not pressed up
-
Mirror Position SW (Dwn) Mirror surface adjust switch signal (Down) / ON or OFF ON: Mirror surface adjust switch pressed down
OFF: Mirror surface adjust switch not pressed down
-

OK:

On the GTS screen, each item changes between ON and OFF according to above chart.

Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C




A

2.INSPECT OUTER MIRROR SWITCH ASSEMBLY

B

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

C

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

2.INSPECT OUTER MIRROR SWITCH ASSEMBLY
a.

Remove the outer mirror switch assembly (See page Vehicle Exterior>MIRROR (EXT)>OUTER MIRROR SWITCH>REMOVAL).


b.

Inspect the outer mirror switch assembly (See page Vehicle Exterior>MIRROR (EXT)>OUTER MIRROR SWITCH>INSPECTION).



OK

3.CHECK HARNESS AND CONNECTOR (OUTER MIRROR SWITCH ASSEMBLY - MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU])

NG

REPLACE OUTER MIRROR SWITCH ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (OUTER MIRROR SWITCH ASSEMBLY - MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU])
a.

Disconnect the G19 outer mirror switch assembly connector.


b.

Disconnect the E137 main body ECU (multiplex network body ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G19-16 (M+) - E137-4 (MIRB) Always Below 1 Ω
G19-13 (MSW) - E137-5 (MIRS) Always Below 1 Ω
G19-14 (E) - E137-6 (MIRE) Always Below 1 Ω
G19-16 (M+) or E137-4 (MIRB) - Body ground Always 10 kΩ or higher
G19-13 (MSW) or E137-5 (MIRS) - Body ground Always 10 kΩ or higher
G19-14 (E) or E137-6 (MIRE) - Body ground Always 10 kΩ or higher



Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C


A

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

B

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

C

REPAIR OR REPLACE HARNESS OR CONNECTOR