The EDU delivers drive signals to fuel injectors using the DC/DC converter, which provides a high-voltage and quick-charging system.
Soon after the EDU receives a fuel injection command (#1 to #8) signal from the ECM, the EDU responds to the command with an injector injection confirmation (INJF) signal when the current is applied to the injector assembly.
| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
|---|---|---|
| Idling for 10 seconds | Open or short in the No. 1 injector driver (EDU) or injector assembly circuit (1 trip detection logic). | ·
Open or short in No. 1 injector driver (EDU) circuit ·
Injector assembly ·
No. 1 EDU ·
ECM |
| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
|---|---|---|
| Idling for 10 seconds | Open or short in the No. 2 injector driver (EDU) or injector assembly circuit (1 trip detection logic). | ·
Open or short in No. 2 injector driver (EDU) circuit ·
Injector assembly ·
No. 2 EDU ·
ECM |
The ECM continuously monitors both injection command (#1 to #8) signals and injection confirmation (INJF) signals. This DTC will be stored if the ECM determines that the number of #1 to #8 signals and INJF signals are inconsistent.
The fuel injectors are grounded over a Field Effect Transistor (FET) and a serial resistor. This resistor creates a voltage drop, which is monitored by the EDU (injector drive circuit) in relation to the current drawn by the injector assembly. When the injector assembly current becomes too high, the voltage drop over the resistor exceeds a specified level and no INJF signal for that cylinder is sent to the ECM.
After the engine is started, when there is no injection confirmation (INJF) signal from the No. 1 or No. 2 EDU to the ECM even though the ECM sends injection command (#1 to #8) signals to the No. 1 or No. 2 EDU, DTC P062D or DTC P062E is stored.
If this DTC is stored, the ECM enters fail-safe mode and limits engine power or stops the engine. The fail-safe mode continues until the ignition switch is turned off.
After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>REGISTRATION) and initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>INITIALIZATION).
After replacing a fuel injector, the ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>REGISTRATION).
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Disconnect the No. 1 injector driver (EDU) connectors.
Disconnect the No. 2 injector driver (EDU) connectors.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| C74-8 (+B) - C73-1 (GND) | Ignition switch ON | 11 to 14 V |
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| C76-8 (+B) - C75-1 (GND) | Ignition switch ON | 11 to 14 V |
OK
NG
Disconnect the injector assembly connectors.
Disconnect the No. 1 EDU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C5-2 - C74-4 (INJ1) | Always | Below 1 Ω |
| C14-2 - C74-3 (INJ4) | Always | Below 1 Ω |
| C69-2 - C74-2 (INJ6) | Always | Below 1 Ω |
| C68-2 - C74-1 (INJ7) | Always | Below 1 Ω |
| C5-1 - C74-5 (COM1) | Always | Below 1 Ω |
| C14-1 - C74-5 (COM1) | Always | Below 1 Ω |
| C69-1 - C74-6 (COM2) | Always | Below 1 Ω |
| C68-1 - C74-6 (COM2) | Always | Below 1 Ω |
| C5-2 or C74-4 (INJ1) - Body ground | Always | 10 kΩ or higher |
| C14-2 or C74-3 (INJ4) - Body ground | Always | 10 kΩ or higher |
| C69-2 or C74-2 (INJ6) - Body ground | Always | 10 kΩ or higher |
| C68-2 or C74-1 (INJ7) - Body ground | Always | 10 kΩ or higher |
| C5-1 or C74-5 (COM1) - Body ground | Always | 10 kΩ or higher |
| C14-1 or C74-5 (COM1) - Body ground | Always | 10 kΩ or higher |
| C69-1 or C74-6 (COM2) - Body ground | Always | 10 kΩ or higher |
| C68-1 or C74-6 (COM2) - Body ground | Always | 10 kΩ or higher |
Disconnect the injector assembly connectors.
Disconnect the No. 2 EDU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C70-2 - C76-4 (INJ2) | Always | Below 1 Ω |
| C9-2 - C76-3 (INJ5) | Always | Below 1 Ω |
| C67-2 - C76-1 (INJ3) | Always | Below 1 Ω |
| C54-2 - C76-2 (INJ8) | Always | Below 1 Ω |
| C70-1 - C76-5 (COM4) | Always | Below 1 Ω |
| C9-1 - C76-5 (COM4) | Always | Below 1 Ω |
| C67-1 - C76-6 (COM5) | Always | Below 1 Ω |
| C54-1 - C76-6 (COM5) | Always | Below 1 Ω |
| C70-2 or C76-4 (INJ2) - Body ground | Always | 10 kΩ or higher |
| C9-2 or C76-3 (INJ5) - Body ground | Always | 10 kΩ or higher |
| C67-2 or C76-1 (INJ3) - Body ground | Always | 10 kΩ or higher |
| C54-2 or C76-2 (INJ8) - Body ground | Always | 10 kΩ or higher |
| C70-1 or C76-5 (COM4) - Body ground | Always | 10 kΩ or higher |
| C9-1 or C76-5 (COM4) - Body ground | Always | 10 kΩ or higher |
| C67-1 or C76-6 (COM5) - Body ground | Always | 10 kΩ or higher |
| C54-1 or C76-6 (COM5) - Body ground | Always | 10 kΩ or higher |
OK
NG
Disconnect the No. 1 EDU connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C73-6 (#10) - C45-40 (#1) | Always | Below 1 Ω |
| C73-5 (#40) - C45-37 (#4) | Always | Below 1 Ω |
| C73-3 (#60) - C45-35 (#6) | Always | Below 1 Ω |
| C73-2 (#70) - C45-34 (#7) | Always | Below 1 Ω |
| C73-7 (INJF) - C45-60 (INJ1) | Always | Below 1 Ω |
| C73-6 (#10) or C45-40 (#1) - Body ground | Always | 10 kΩ or higher |
| C73-5 (#40) or C45-37 (#4) - Body ground | Always | 10 kΩ or higher |
| C73-3 (#60) or C45-35 (#6) - Body ground | Always | 10 kΩ or higher |
| C73-2 (#70) or C45-34 (#7) - Body ground | Always | 10 kΩ or higher |
| C73-7 (INJF) or C45-60 (INJ1) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C73-6 (#10) - C46-40 (#1) | Always | Below 1 Ω |
| C73-5 (#40) - C46-37 (#4) | Always | Below 1 Ω |
| C73-3 (#60) - C46-35 (#6) | Always | Below 1 Ω |
| C73-2 (#70) - C46-34 (#7) | Always | Below 1 Ω |
| C73-7 (INJF) - C46-60 (INJ1) | Always | Below 1 Ω |
| C73-6 (#10) or C46-40 (#1) - Body ground | Always | 10 kΩ or higher |
| C73-5 (#40) or C46-37 (#4) - Body ground | Always | 10 kΩ or higher |
| C73-3 (#60) or C46-35 (#6) - Body ground | Always | 10 kΩ or higher |
| C73-2 (#70) or C46-34 (#7) - Body ground | Always | 10 kΩ or higher |
| C73-7 (INJF) or C46-60 (INJ1) - Body ground | Always | 10 kΩ or higher |
Disconnect the No. 2 EDU connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C75-6 (#20) - C45-39 (#2) | Always | Below 1 Ω |
| C75-2 (#30) - C45-38 (#3) | Always | Below 1 Ω |
| C75-5 (#50) - C45-36 (#5) | Always | Below 1 Ω |
| C75-3 (#80) - C45-33 (#8) | Always | Below 1 Ω |
| C75-7 (INF2) - C45-61 (INJ2) | Always | Below 1 Ω |
| C75-6 (#20) or C45-39 (#2) - Body ground | Always | 10 kΩ or higher |
| C75-2 (#30) or C45-38 (#3) - Body ground | Always | 10 kΩ or higher |
| C75-5 (#50) or C45-36 (#5) - Body ground | Always | 10 kΩ or higher |
| C75-3 (#80) or C45-33 (#8) - Body ground | Always | 10 kΩ or higher |
| C75-7 (INF2) or C45-61 (INJ2) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C75-6 (#20) - C46-39 (#2) | Always | Below 1 Ω |
| C75-2 (#30) - C46-38 (#3) | Always | Below 1 Ω |
| C75-5 (#50) - C46-36 (#5) | Always | Below 1 Ω |
| C75-3 (#80) - C46-33 (#8) | Always | Below 1 Ω |
| C75-7 (INF2) - C46-61 (INJ2) | Always | Below 1 Ω |
| C75-6 (#20) or C46-39 (#2) - Body ground | Always | 10 kΩ or higher |
| C75-2 (#30) or C46-38 (#3) - Body ground | Always | 10 kΩ or higher |
| C75-5 (#50) or C46-36 (#5) - Body ground | Always | 10 kΩ or higher |
| C75-3 (#80) or C46-33 (#8) - Body ground | Always | 10 kΩ or higher |
| C75-7 (INF2) or C46-60 (INJ2) - Body ground | Always | 10 kΩ or higher |
OK
NG
Inspect the injector assembly (See page Engine / Hybrid System>1VD-FTV (FUEL)>FUEL INJECTOR (w/o DPF)>INSPECTION).
OK
NG
Interchange the No. 1 and No. 2 EDU connectors.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Clear the DTCs (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>DTC CHECK / CLEAR).
Before clearing the DTCs, write them down.
Start the engine.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTCs do not change | A |
| DTCs change (change in malfunctioning cylinder or EDU code) | B |
A
B
Replace the ECM (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECM>REMOVAL).
NEXT
Go to the injector circuit (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>Injector Circuit).
NEXT
Replace the injector driver (No. 1 or No. 2) (See page Engine / Hybrid System>1VD-FTV (FUEL)>INJECTOR DRIVER>REMOVAL).
NEXT
Replace the injector assembly (See page Engine / Hybrid System>1VD-FTV (FUEL)>FUEL INJECTOR (w/o DPF)>REMOVAL).
NEXT
NEXT
Connect the GTS to the DLC3.
Clear the DTCs (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>DTC CHECK / CLEAR).
Turn the ignition switch off.
Start the engine and idle it for 10 seconds.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Confirm that the DTC is not output again.
NEXT