When the retractable outer mirror switch is pushed, the main body ECU (multiplex network body ECU) received retract/return signal from the retractable outer mirror switch. Then main body ECU (multiplex network body ECU) sends the retract/return signal to outer mirror control ECU LH and RH via the CAN communication line. The outer mirror control ECU assembly then performs control in response to the retract/return signal.
First perform the communication function inspections in How to Proceed with Troubleshooting to confirm that there are no CAN communication malfunctions before troubleshooting this problem.
Using the GTS, read the Data List. (See page Vehicle Exterior>MIRROR (EXT)>POWER MIRROR CONTROL SYSTEM(w/ Retract Mirror)>DATA LIST / ACTIVE TEST).
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Outer Mirror Fold SW | Retractable outer mirror switch signal / ON or OFF | ON: Retractable outer mirror switch in retract position
OFF: Retractable outer mirror switch not in retract position |
- |
On the GTS screen, each item changes between ON and OFF according to above chart.
OK
NG
Check the malfunctioning outer rear view mirror assembly (See page Vehicle Exterior>MIRROR (EXT)>POWER MIRROR CONTROL SYSTEM(w/ Retract Mirror)>OPERATION CHECK).
| Result | Proceed to |
|---|---|
| Both outer rear view mirror assembly LH and RH do not operate (for LHD) | A |
| Both outer rear view mirror assembly LH and RH do not operate (for RHD) | B |
| Outer rear view mirror assembly LH does not operate | C |
| Outer rear view mirror assembly RH does not operate | D |
A
B
C
D
Remove the outer rear view mirror assembly LH (See page Vehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR>REMOVAL).
Inspect the outer rear view mirror assembly LH (See page Vehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR>INSPECTION).
OK
NG
Disconnect the I35 outer rear view mirror assembly LH connector.
Disconnect the I40 outer mirror control ECU assembly LH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I35-19 (MR) - I40-3 (MR+) | Always | Below 1 Ω |
| I35-20 (MF) - I40-11 (MR-) | ||
| I35-19 (MR) or I40-3 (MR+) - Body ground | Always | 10 kΩ or higher |
| I35-20 (MF) or I40-11 (MR-) - Body ground |
OK
NG
Remove the outer rear view mirror assembly RH (See page Vehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR>REMOVAL).
Inspect the outer rear view mirror assembly RH (See pageVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR>INSPECTION ).
OK
NG
Disconnect the I32 outer rear view mirror assembly RH connector.
Disconnect the I37 outer mirror control ECU assembly RH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I32-19 (MR) - I37-3 (MR+) | Always | Below 1 Ω |
| I32-20 (MF) - I37-11 (MR-) | ||
| I32-19 (MR) or I37-3 (MR+) - Body ground | Always | 10 kΩ or higher |
| I32-20 (MF) or I37-11 (MR-) - Body ground |
OK
NG
Remove the retractable outer mirror switch (See page Vehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR>REMOVAL).
Inspect the retractable outer mirror switch (See page Vehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR>INSPECTION).
OK
NG
Disconnect the G26 retractable outer mirror switch connector.
Disconnect the E117 main body ECU (multiplex network body ECU ) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G26-2 (MR) - E117-14 (RET) | Always | Below 1 Ω |
| G26-3 (MAT) - E117-15 (AMR) | ||
| G26-4 (E) - Body ground | ||
| G26-2 (MR) or E117-14 (RET) - Body ground | Always | 10 kΩ or higher |
| G26-3 (MAT) or E117-15 (AMR) - Body ground |
| Result | Proceed to |
|---|---|
| OK (for LHD) | A |
| OK (for RHD) | B |
| NG | C |
A
B
C