31353
1.INSTALL CLUTCH PEDAL SPRING HOLDER
Apply MP grease to the contact surface of the clutch pedal spring holder.
Install the clutch pedal spring holder to the clutch pedal support sub-assembly.
31453B
2.INSTALL CLUTCH MASTER CYLINDER PUSH ROD CLEVIS BUSH
Apply MP grease to the inside of a new clutch master cylinder push rod clevis bush.
Install the clutch master cylinder push rod clevis bush to the clutch pedal sub-assembly.
Install the clutch master cylinder push rod clevis bush from the right side of the vehicle.
31301P
3.INSTALL CLUTCH PEDAL TURNOVER BUSH
Apply MP grease to the inside of the clutch pedal turnover bush.
Install the clutch pedal turnover bush to the clutch pedal sub-assembly.
31301S
4.INSTALL NO. 2 CLUTCH PEDAL CUSHION
Install the 2 No. 2 clutch pedal cushions to the clutch pedal sub-assembly.
31301C
5.INSTALL CLUTCH PEDAL BUSH
Apply MP grease to the inside and outside of 2 new clutch pedal bushes.
Install the 2 clutch pedal bushes to the clutch pedal sub-assembly.
31324A
6.INSTALL CLUTCH PEDAL SHAFT COLLAR
Apply MP grease to the clutch pedal shaft collar.
Install the clutch pedal shaft collar to the clutch pedal sub-assembly.
31321
7.INSTALL CLUTCH PEDAL PAD
Install the clutch pedal pad to the clutch pedal sub-assembly.
31301
8.INSTALL CLUTCH PEDAL SUB-ASSEMBLY
Install the clutch pedal sub-assembly to the clutch pedal support with the nut, washer and bolt.
Install the bolt from the right side of the vehicle.
Apply MP grease to the contact surface of the clevis pin and clutch master cylinder push rod clevis bush.
Install the wave washer to the clevis pin.
Connect the clevis of the master cylinder assembly to the clutch pedal sub-assembly with the clevis pin.
Install a new clip to the clevis pin.
31301A
9.INSTALL CLUTCH PEDAL SPRING
Apply MP grease to the inside and outside of the spacer and pin of the clutch pedal support sub-assembly.
Install the spacer to the clutch pedal spring.
Install the clutch spring to the clutch pedal support sub-assembly with 2 new E-rings.
31301R
10.INSTALL TURNOVER SPRING
Apply MP grease to the contact surfaces of the clutch pedal spring holder, clutch pedal sub-assembly and turnover spring.
Move the pedal to the full stroke position.
Install the clutch spring to the clutch pedal sub-assembly and clutch pedal spring holder.
11.INSTALL CLUTCH PEDAL SUPPORT ASSEMBLY WITH CLUTCH MASTER CYLINDER
Install the clutch pedal support assembly with clutch master cylinder with the bolt and 2 nuts.
Connect the clutch start switch connector.
w/ Cruise Control System:
Connect the clutch switch connector.
31481
12.CONNECT CLUTCH MASTER CYLINDER TO FLEXIBLE HOSE TUBE AND CLUTCH RESERVOIR TUBE
Using a union nut wrench, connect the flexible hose tube.
Calculate the torque wrench readingwhen changing the fulcrum length ofthe torque wrench.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
When using a union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torquewrench (fulcrum length of 300 mm (11.811 in.)): 14.2 N*m (145 kgf*cm, 10 ft.*lbf)
Connect the clutch reservoir tube with a new clip.
82733A
13.INSTALL MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH)
14.FILL RESERVOIR WITH BRAKE FLUID
15.BLEED CLUTCH LINE
31301
16.INSPECT AND ADJUST CLUTCH PEDAL SUB-ASSEMBLY
17.CHECK FLUID LEVEL IN RESERVOIR
18.INSPECT FOR CLUTCH FLUID LEAK
55303B
19.INSTALL LOWER INSTRUMENT PANEL SUB-ASSEMBLY (w/o Driver Side Knee Airbag)
73900
20.INSTALL LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY (w/ Driver Side Knee Airbag)