Home › Vehicle Interior › INTERIOR PANELS / TRIM › INSTRUMENT PANEL SAFETY PAD › from 2016.08
RM2660E _58 Vehicle Interior _052849 INTERIOR PANELS / TRIM _0255717 INSTRUMENT PANEL SAFETY PAD A

INTERIOR PANELS / TRIM  INSTRUMENT PANEL SAFETY PAD  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.

·

A bolt without a torque specification is shown in the standard bolt chart.

Click hereGeneral>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS



PROCEDURE

Hide 55400 1.INSTALL INSTRUMENT PANEL SAFETY PAD ASSEMBLY

a.

Install the instrument panel safety pad assembly with the 6 bolts <E>, 2 nuts <F> and 2 bolts <B>.


b.

Install the 2 passenger airbag installation bolts <D>.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


c.

Connect each connector.

U156001C01
1.729,0.979 1.979,1.156 1.979,1.156 1.917,0.969 true 1.135,1.063 1.323,1.24 0.188,0.177 10 false *f 1.229,0.875 1.417,1.052 0.188,0.177 10 true *e 2.031,0.604 2.219,0.781 0.188,0.177 10 true *d 0.781,0.635 0.969,0.813 0.188,0.177 10 true *d 2,1.094 2.188,1.271 0.188,0.177 10 true *e 6.656,1.458 6.844,1.635 0.188,0.177 10 false *a 0.25,3.24 0.438,3.417 0.188,0.177 10 false *a 5.115,2.604 5.302,2.781 0.188,0.177 10 false *a 4.76,3.354 4.948,3.531 0.188,0.177 10 false *a 6.469,2.229 6.656,2.406 0.188,0.177 10 false *a 1.344,4.438 1.531,4.615 0.188,0.177 10 false *c 6.333,2.979 6.521,3.156 0.188,0.177 10 false *c 3.146,2.792 3.333,2.969 0.188,0.177 10 true *b 3.083,3.75 3.271,3.927 0.188,0.177 10 false *a 2.281,2.885 2.469,3.063 0.188,0.177 10 false *b
*a Bolt <E> *b Nut <F>
*c Bolt <B> *d Passenger Airbag Installation Bolt <D>
*e Connector *f Passenger Airbag Connector



d.
U155893C01
1.813,0.252 2.004,0.431 0.192,0.179 10 *a 2.736,0.237 2.927,0.416 0.192,0.179 10 *b 1.78,0.926 1.888,0.446 false 2.719,0.915 2.827,0.436 false
*a Lock Slider
*b Lock Position


Connect the passenger airbag connector.

NOTICE:

When handling the passenger airbag connector, take care not to damage the airbag wire harness.



e.

Check that the lock slider is in the lock position.


f.

Connect each connector and attach each clamp.


g.

Connect the wire harness with the 2 bolts.

U155757C02
6.771,1.083 6.958,1.26 0.188,0.177 10 true *a 6.792,0.833 6.979,1.01 0.188,0.177 10 true *b 6.771,1.302 6.958,1.479 0.188,0.177 10 true *a 6.75,1.573 6.938,1.75 0.188,0.177 10 true *a 4.25,5 4.438,5.177 0.188,0.177 10 true *a 4.323,5.323 4.51,5.5 0.188,0.177 10 true *a 6.76,5.375 6.948,5.552 0.188,0.177 10 true *b 3.073,5.427 3.26,5.604 0.188,0.177 10 true *a
*a Connector *b Bolt



h.

Connect each connector and attach each clamp.

U164418C02
1.156,1.75 1.448,1.958 0.292,0.208 12 false *A 4.25,1.771 4.51,1.99 0.26,0.219 12 true *B
*A w/ Multi-terrain Monitor System *B w/ TOYOTA Parking Assist-sensor System



Hide 87212H 2.INSTALL REAR NO. 4 AIR DUCT (w/ Rear Air Duct)

B180308

a.

Attach the clip to install the rear No. 4 air duct.


Hide 87212F 3.INSTALL REAR NO. 2 AIR DUCT (w/ Rear Air Duct)

B180309

a.

Attach the clip to install the rear No. 2 air duct.


Hide 55405B 4.INSTALL CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY

a.

w/o Wireless Charger:

i.
B432518

Connect the connectors.


ii.

Attach the 6 claws to install the center instrument cluster finish panel sub-assembly.



b.

w/ Wireless Charger:

i.
B432519

Connect the connectors.


ii.

Attach the 6 claws to install the center instrument cluster finish panel sub-assembly.



Hide 86160P 5.INSTALL FRONT NO. 2 SPEAKER ASSEMBLY

HINT:

Use the same procedure for the RH and LH side.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER>INSTALLATION


Hide 86160L 6.INSTALL FRONT NO. 4 SPEAKER ASSEMBLY (w/ Front Center Speaker)

Hide 55408F 7.INSTALL NO. 1 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY

B421869

a.

Attach the 2 guides.


b.

Attach the 3 claws to install the No. 1 instrument panel speaker panel sub-assembly.


Hide 55409F 8.INSTALL NO. 2 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY

B421867

a.

Attach the 2 guides.


b.

Attach the 3 claws to install the No. 2 instrument panel speaker panel sub-assembly.


Hide 55510F 9.INSTALL NO. 1 SPEAKER OPENING COVER ASSEMBLY

B421865

a.

Attach the 8 clips to install the No. 1 speaker opening cover assembly.


Hide 86130A 13.INSTALL MULTI-MEDIA MODULE RECEIVER ASSEMBLY (w/ Navigation System)

Hide 14.INSTALL AIR CONDITIONING CONTROL ASSEMBLY (w/o Navigation System)

Hide 86110B 15.INSTALL MULTI-DISPLAY ASSEMBLY (w/ Navigation System)

Hide 55522B 16.INSTALL RADIO TUNER OPENING COVER (w/o Radio Receiver)

B180654

a.

Install the radio tuner opening cover with the 2 bolts and 2 screws.

Torque:
Bolt : 8.5 N*m (87 kgf*cm, 75 in.*lbf)


Hide 86120 17.INSTALL RADIO RECEIVER ASSEMBLY (for Radio Receiver Type)

Hide 86140A 18.INSTALL RADIO AND DISPLAY RECEIVER ASSEMBLY (for Radio and Display Type)

Hide 55412C 19.INSTALL NO. 1 CENTER INSTRUMENT CLUSTER FINISH PANEL (w/o Navigation System)

B421870

a.

for Type A:

i.

Connect the connector.


ii.

Attach the 8 claws and 3 clips to install the No. 1 center instrument cluster finish panel.



b.

for Type B:

i.
B180653

Connect the connector.


ii.

Attach the 10 claws to install the No. 1 center instrument cluster finish panel.



Hide 55670 20.INSTALL NO. 3 INSTRUMENT PANEL REGISTER ASSEMBLY

a.

for Type A:

i.
B432535

Attach the guide and 7 claws to install the No. 3 instrument panel register assembly.



b.

for Type B:

i.
B435724

Attach the 6 claws to install the No. 3 instrument panel register assembly.



Hide 55680A 21.INSTALL NO. 4 INSTRUMENT PANEL REGISTER ASSEMBLY

a.

for Type A:

i.
B432536

Attach the guide and 7 claws to install the No. 4 instrument panel register assembly.



b.

for Type B:

i.
B435725

Attach the 6 claws to install the No. 4 instrument panel register assembly.



Hide 55660 22.INSTALL NO. 2 INSTRUMENT PANEL REGISTER ASSEMBLY

B432537

a.

Attach the 4 claws to install the No. 2 instrument panel register assembly.


Hide 55433B 23.INSTALL LOWER NO. 2 INSTRUMENT PANEL FINISH PANEL

B432510

a.

Connect the connector.


b.

Attach the 3 claws to install the lower No. 2 instrument panel finish panel.


c.
U156003C01
0.747,1.018 0.939,1.197 0.192,0.179 10 *a 2.609,1.018 2.801,1.197 0.192,0.179 10 *a 0.598,1.791 0.790,1.970 0.192,0.179 10 *a 2.529,1.877 2.721,2.056 0.192,0.179 10 *a
*a Screw <C>


Install the 4 screws <C>.


Hide 55443D 24.INSTALL INSTRUMENT PANEL BOX DOOR KNOB

HINT:

Use the same procedure for both instrument panel box door knobs.


a.
B182549

Attach the 2 claws to install the instrument panel box door knob.


Hide 55476A 25.INSTALL NO. 3 INSTRUMENT CLUSTER FINISH PANEL GARNISH

B432539

a.

Attach the 6 claws to install the No. 3 instrument cluster finish panel garnish.


Hide 55312 26.INSTALL LOWER INSTRUMENT PANEL (w/o Passenger Side Knee Airbag)

U163957C02
0.5,1.555 0.692,1.734 0.192,0.179 10 *a 2.475,1.852 2.666,2.031 0.192,0.179 10 *a
*a Bolt <B>


a.

Attach the 4 claws to install the lower instrument panel.


b.

Install the 2 bolts <B>.


Hide 73990 27.INSTALL LOWER NO. 2 INSTRUMENT PANEL AIRBAG ASSEMBLY (w/ Passenger Side Knee Airbag)

Hide 62111C 28.INSTALL COWL SIDE TRIM BOARD RH

U155994C01
0.696,0.961 0.888,1.140 0.192,0.179 10 *a
*a Cap Nut


a.

Attach the 2 clips to install the cowl side trim board RH.


b.

Install the cap nut.


Hide 55607 29.INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (w/ Floor Under Cover)

B432506

a.

Connect the connector.


b.

Attach the 3 guides.


c.

Attach the 4 claws to install the No. 2 instrument panel under cover sub-assembly.


Hide 55317A 31.INSTALL INSTRUMENT SIDE PANEL RH

B432540

a.

w/ Airbag Cut Off Switch:

i.

Connect the connector.



b.

Attach the 6 claws to install the instrument side panel RH.


Hide 55650 32.INSTALL NO. 1 INSTRUMENT PANEL REGISTER ASSEMBLY

B432541

a.

Attach the 4 claws to install the No. 1 instrument panel register assembly.


Hide 55303B 33.INSTALL LOWER INSTRUMENT PANEL SUB-ASSEMBLY (w/o Driver Side Knee Airbag)

U163956C02
0.799,1.869 0.990,2.048 0.192,0.179 10 *a 1.796,1.606 1.988,1.785 0.192,0.179 10 *a 2.667,1.034 2.859,1.213 0.192,0.179 10 *a 2.872,0.618 3.064,0.797 0.192,0.179 10 *a 1.584,0.868 1.775,1.047 0.192,0.179 10 *a
*a Bolt <B>


a.

Attach the 2 claws and connect the DLC3.


b.

Install the lower instrument panel sub-assembly with the 5 bolts.


Hide 73900 34.INSTALL LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY (w/ Driver Side Knee Airbag)

Hide 55446A 35.INSTALL NO. 1 SWITCH HOLE BASE

B432542

a.

Connect the connectors.


b.

Attach the 4 claws to install the No. 1 switch hole base.


Hide 55432D 36.INSTALL LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL

a.

Connect the connectors.


b.
B181942

Attach the 2 claws to connect the 2 control cables.


c.

for Automatic Air Conditioning System:

i.
B180296

Attach the 2 claws to install the room temperature sensor.



d.

w/ Driver Side Knee Airbag:

i.

Attach the 16 claws to install the lower No. 1 instrument panel finish panel.

B434077



e.

w/o Driver Side Knee Airbag:

i.

Attach the 9 claws to install the lower No. 1 instrument panel finish panel.

B434078



f.
U156004C01
1.146,1.76 1.458,1.958 0.313,0.198 10 false *a 2.719,1.813 3.031,2.01 0.313,0.198 10 false *a
*a Bolt <B>


Install the 2 bolts <B>.


g.
B182569

Attach the 2 claws to close the hole cover.


Hide 62112 37.INSTALL COWL SIDE TRIM BOARD LH

U155989C02
2.437,0.892 2.629,1.071 0.192,0.179 10 *a
*a Cap Nut


a.

Attach the 2 clips to install the cowl side trim board LH.


b.

Install the cap nut.


Hide 55606 38.INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (w/ Floor Under Cover)

B452058C01
2.156,0.385 2.375,0.594 0.219,0.208 10 true *a 2.99,0.604 3.208,0.813 0.219,0.208 10 true *a
*a Screw <A>


a.

for Automatic Transmission:

i.

Connect the connector.


ii.

Attach the 2 guides and 3 claws to install the No. 1 instrument panel under cover sub-assembly.


iii.

Install the 2 screws <A>.



b.
B452056C01
1.656,0.385 1.969,0.583 0.313,0.198 10 true *a 2.823,0.854 3.021,1.052 0.198,0.198 10 true *a
*a Screw <A>


for Manual Transmission:

i.

Connect the connector.


ii.

Attach the guide and 2 claws to install the No. 1 instrument panel under cover sub-assembly.


iii.

Install the 2 screws <A>.



Hide 83100 40.INSTALL COMBINATION METER ASSEMBLY

a.

Connect the connectors.


b.
B432499

Install the combination meter assembly with the 4 screws.


Hide 55404C 41.INSTALL NO. 2 INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY

a.

w/ Light Control Rheostat:

Connect the connector.


b.

w/ Blind Spot Monitor System:

Connect the connector.


c.
B432544

Attach the 9 claws to install the No. 2 instrument cluster finish panel sub-assembly.


Hide 55475A 42.INSTALL NO. 2 INSTRUMENT CLUSTER FINISH PANEL GARNISH

B432545

a.

Attach the 2 claws to install the No. 2 instrument cluster finish panel garnish.


Hide 55474C 43.INSTALL NO. 1 INSTRUMENT CLUSTER FINISH PANEL GARNISH

B432546

a.

Attach the 3 claws to install the No. 1 instrument cluster finish panel garnish.


Hide 55318C 44.INSTALL INSTRUMENT SIDE PANEL LH

B432547

a.

Attach the 6 claws to install the instrument side panel LH.


Hide 58901A 45.INSTALL REAR CONSOLE BOX SUB-ASSEMBLY (w/o Cool Box)

Hide 88520 46.INSTALL COOLING BOX ASSEMBLY (w/ Cool Box)

Hide 58812A 47.INSTALL LOWER CONSOLE BOX (w/o Console Box Lid)

Hide 84140 48.INSTALL HEADLIGHT DIMMER SWITCH ASSEMBLY

Hide 49.INSTALL FRONT SEAT ASSEMBLY LH

Hide 51.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click here


Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

Hide 52.CHARGE REFRIGERANT (w/ Cool Box)

Hide 54.CHECK FOR REFRIGERANT GAS LEAK (w/ Cool Box)

Hide 55.ENABLE AUTOAWAY/RETURN FUNCTION (for Power Tilt and Power Telescopic Steering Column)

a.

Restore the autoaway/return function setting to the previous condition by changing the customize parameter.

Click hereSteering>STEERING COLUMN>POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM>CUSTOMIZE PARAMETERS