Home › Steering › VARIABLE GEAR RATIO STEERING › VARIABLE GEAR RATIO STEERING SYSTEM › from 2015.08
RM2660E _55 Steering _052825 VARIABLE GEAR RATIO STEERING _0255448 VARIABLE GEAR RATIO STEERING SYSTEM C

VARIABLE GEAR RATIO STEERING  VARIABLE GEAR RATIO STEERING SYSTEM  C15B2/72  ECU Malfunction(Internal Line)  


DESCRIPTION

If the VGRS ECU (steering control ECU) detects a malfunction in the circuit between the motor and ECU or an internal malfunction, it stores these DTCs and turns the master warning light on.

DTC No. DTC Detection Condition Trouble Area
C15B2/72 When the engine switch is turned on (IG), the VGRS ECU (steering control ECU) detects a malfunction in the circuit between the motor and ECU or an internal malfunction.
·

Steering actuator assembly

·

VGRS ECU (steering control ECU)

·

Harness or connector



WIRING DIAGRAM

C421096E18
4.698,6.729 6.958,7.042 2.26,0.313 10 false VGRS ECU (Steering Control ECU) 1.375,0.781 2.427,1.083 1.052,0.302 10 false from IG Circuit 1.469,1.354 2.948,1.76 1.479,0.406 10 false from Battery 3.49,0.958 4.469,1.25 0.979,0.292 10 false ECU-IG NO. 1 5.052,0.771 5.479,0.927 0.427,0.156 10 false E161 3.698,1.51 4.229,1.74 0.531,0.229 10 false VGRS 5.51,1.375 5.906,1.573 0.396,0.198 10 false PIG 5.51,1.906 6.083,2.104 0.573,0.198 10 false PGND 5.521,0.792 5.917,0.99 0.396,0.198 10 false IG 5.188,0.583 5.448,0.74 0.26,0.156 10 false 4 5.156,1.667 5.417,1.823 0.26,0.156 10 false 1 5.156,1.156 5.417,1.313 0.26,0.156 10 false 2 5.063,2.854 5.635,3.01 0.573,0.156 10 false E160 5.521,2.854 5.917,3.052 0.396,0.198 10 false BMU 5.531,3.469 5.927,3.667 0.396,0.198 10 false BMV 0.688,4.146 1.271,4.375 0.583,0.229 10 false BMW+ 5.51,4.667 5.906,4.865 0.396,0.198 10 false SG 5.198,3.271 5.448,3.469 0.25,0.198 10 false 2 5.198,2.688 5.458,2.844 0.26,0.156 10 false 3 5.198,3.906 5.5,4.073 0.302,0.167 10 false 1 5.188,4.469 5.49,4.635 0.302,0.167 10 false 5 3,4.781 3.729,4.99 0.729,0.208 10 false Shielded 3.021,6.438 3.75,6.646 0.729,0.208 10 false Shielded 0.188,6.865 2.323,7.417 2.135,0.552 10 false Steering Actuator Assembly 0.198,6.698 0.625,6.854 0.427,0.156 10 false E80 0.719,2.865 1.24,3.063 0.521,0.198 10 false BMU+ 0.719,3.458 1.219,3.677 0.5,0.219 10 false BMV+ 5.542,4.115 6.021,4.313 0.479,0.198 10 false BMW 5.177,5.146 5.427,5.344 0.25,0.198 10 false 2 5.188,5.615 5.49,5.781 0.302,0.167 10 false 6 5.146,6.073 5.406,6.229 0.26,0.156 10 false 10 5.531,6.24 5.927,6.438 0.396,0.198 10 false SG2+ 5.052,5.323 5.573,5.479 0.521,0.156 10 false E162 5.531,5.344 5.927,5.542 0.396,0.198 10 false LV 5.51,5.802 5.906,6 0.396,0.198 10 false LG 0.844,5.344 1.24,5.542 0.396,0.198 10 false LV+ 0.844,5.802 1.24,6 0.396,0.198 10 false LG+ 1.26,5.698 1.521,5.854 0.26,0.156 10 false 16 1.281,5.24 1.583,5.406 0.302,0.167 10 false 7 1.271,2.76 1.531,2.917 0.26,0.156 10 false 4 1.271,3.365 1.531,3.521 0.26,0.156 10 false 5 1.229,4.031 1.49,4.188 0.26,0.156 10 false 13 5.042,1.354 5.438,1.552 0.396,0.198 10 false E159 5.031,1.854 5.427,2.052 0.396,0.198 10 false E159 5.052,4.104 5.625,4.26 0.573,0.156 10 false E160 5.052,4.635 5.625,4.792 0.573,0.156 10 false E160 5.063,3.458 5.635,3.615 0.573,0.156 10 false E160 5.052,5.781 5.573,5.938 0.521,0.156 10 false E162 5.063,6.24 5.583,6.396 0.521,0.156 10 false E162

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the VGRS ECU (steering control ECU) or steering actuator assembly, perform actuator angle neutral point calibration and initialization after replacing parts.

Click hereSteering>VARIABLE GEAR RATIO STEERING>VARIABLE GEAR RATIO STEERING SYSTEM>CALIBRATION

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (PIG, PGND TERMINAL)
a.
C425413C18
1.333,0.313 1.813,0.542 0.479,0.229 1.417,1.167 1.25,1.417 1.25,1.417 1.25,1.656 true 1.667,1.167 1.833,1.417 1.833,1.417 1.833,1.667 true 0.104,0.094 0.417,0.292 0.313,0.198 10 false *a 1.417,0.344 2.021,0.521 0.604,0.177 10 false E159 1.031,1.688 1.521,1.885 0.49,0.198 10 false 2 (PIG) 1.583,1.698 2.198,1.885 0.615,0.188 10 false 1 (PGND)
*a Component with harness connected
(VGRS ECU [Steering Control ECU])


Turn the engine switch off.


b.

Measure the resistance according to the value(s) in the table below.

HINT:

Perform the inspection from the rear of the connector with the connector connected to the VGRS ECU (steering control ECU).


Standard Resistance:
Tester Connection Condition Specified Condition
E159-1(PGND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
E159-2(PIG) - E159-1(PGND) Engine switch off 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.INSPECT VGRS ECU (STEERING CONTROL ECU) (LV, LG TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT VGRS ECU (STEERING CONTROL ECU) (LV, LG TERMINAL)
a.

Check the connection condition of the VGRS ECU (steering control ECU) connector and terminals.


b.
C425413C19
1.677,0.271 2.177,0.5 0.5,0.229 1.583,1.75 1.583,1.594 1.583,1.594 1.99,1.063 true 2.333,1.75 2.333,1.583 2.333,1.583 2.042,1.156 true 0.115,0.104 0.302,0.281 0.188,0.177 10 false *a 1.76,0.302 2.375,0.5 0.615,0.198 10 false E162 1.417,1.771 1.865,1.958 0.448,0.188 10 false 2 (LV) 2.167,1.781 3.083,1.979 0.917,0.198 10 false 6 (LG)
*a Component with harness connected
(VGRS ECU [Steering Control ECU])


Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

HINT:

With the connector connected to the VGRS ECU (steering control ECU), measure the voltage from the rear of the connector.


Standard Voltage:
Tester Connection Condition Specified Condition
E162-2 (LV) - Body ground Engine switch on (IG) 11 to 14 V
E162-6 (LG) - Body ground Engine switch on (IG) 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.READ VALUE USING GTS (LOCK SOLENOID VOLTAGE)

NG

4.INSPECT STEERING ACTUATOR ASSEMBLY
3.READ VALUE USING GTS (LOCK SOLENOID VOLTAGE)
a.

Turn the engine switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the engine switch on (IG).


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / VGRS / Data List.

VGRS
Tester Display Measurement Item /Range Normal Condition Diagnostic Note
Lock Solenoid Voltage Lock solenoid voltage/
Min.: 0.00 V
Max.: 255.99 V
0 to 14 V -


OK:

0 to 14 V (engine switch on [IG])


Result:
Proceed to
OK
NG



OK

4.INSPECT STEERING ACTUATOR ASSEMBLY

NG

4.INSPECT STEERING ACTUATOR ASSEMBLY
a.

Turn the engine switch off.


b.
C424789C18
1.458,2.823 1.896,3.031 0.438,0.208 1.427,0.646 1.865,0.854 0.438,0.208 0.917,2.135 0.917,1.917 0.917,1.917 1.146,1.573 true 2.25,2.125 2.25,1.948 2.25,1.948 1.938,1.573 true 1.573,2.104 1.563,1.594 true 0.833,3.396 1.042,3.396 1.042,3.396 1.49,3.635 true 0.854,4.031 1.031,4.031 1.031,4.031 1.385,3.875 true 0.125,0.177 0.438,0.333 0.313,0.156 10 false *a 1.521,2.854 2.135,3.052 0.615,0.198 10 false E162 0.719,2.25 1.177,2.448 0.458,0.198 10 false BMW 1.438,2.26 1.896,2.458 0.458,0.198 10 false BMV 2.125,2.26 2.583,2.458 0.458,0.198 10 false BMU 0.635,3.354 0.906,3.552 0.271,0.198 10 false LV 0.635,3.979 0.906,4.177 0.271,0.198 10 false LG 1.5,0.677 2.115,0.875 0.615,0.198 10 false E160
*a Front view of wire harness connector
(to VGRS ECU [Steering Control ECU])


Disconnect the E160 and E162 VGRS ECU (steering control ECU) connectors.


c.

Measure the resistance according to the value(s) in the table below.

HINT:

Measure the resistance of the steering actuator assembly at the connector of the VGRS ECU (steering control ECU).


Standard Resistance:
Tester Connection Condition Specified Condition
E160-2 (BMV) - E160-3 (BMU) Always Below 1 Ω
E160-2 (BMV) - E160-1 (BMW) Always Below 1 Ω
E160-3 (BMU) - E160-1 (BMW) Always Below 1 Ω
E162-2 (LV) - E162-6 (LG) Always 10 to 30 Ω
E160-1 (BMW) - Body ground Always 100 kΩ or higher
E160-2 (BMV) - Body ground Always 100 kΩ or higher
E160-3 (BMU) - Body ground Always 100 kΩ or higher
E162-2 (LV) - Body ground Always 100 kΩ or higher
E162-6 (LG) - Body ground Always 100 kΩ or higher



Result:
Result Proceed to
The resistance value deviates from the standard A
The resistance value is within the standard B



A

5.RECONFIRM DTC

B

6.CHECK HARNESS AND CONNECTOR (VGRS ECU (STEERING CONTROL ECU) - STEERING ACTUATOR ASSEMBLY)
5.RECONFIRM DTC
a.

Reconnect the E160 and E162 VGRS ECU (steering control ECU) connectors.



c.

Turn the engine switch off.



Result:
Result Proceed to
DTC C15B2/72 is not output A
DTC C15B2/72 is output B



A

B

6.CHECK HARNESS AND CONNECTOR (VGRS ECU (STEERING CONTROL ECU) - STEERING ACTUATOR ASSEMBLY)
a.

Turn the engine switch off.


b.

Disconnect the E160 and E162 VGRS ECU (steering control ECU) connectors.


c.

Disconnect the E80 steering actuator assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E160-2 (BMV) - E80-5 (BMV+) Always Below 1 Ω
E160-3 (BMU) - E80-4 (BMU+) Always Below 1 Ω
E160-1 (BMW) - E80-13 (BMW+) Always Below 1 Ω
E160-2 (BMV) - E160-3 (BMU) Always 100 kΩ or higher
E160-2 (BMV) - E160-1 (BMW) Always 100 kΩ or higher
E160-3 (BMU) - E160-1 (BMW) Always 100 kΩ or higher
E160-2 (BMV) or E80-5 (BMV+) - Body ground Always 100 kΩ or higher
E160-3 (BMU) or E80-4 (BMU+) - Body ground Always 100 kΩ or higher
E160-1 (BMW) or E80-13 (BMW+) - Body ground Always 100 kΩ or higher
E162-2 (LV) - E80-7 (LV+) Always Below 1 Ω
E162-6 (LG) - E80-16 (LG+) Always Below 1 Ω
E162-2 (LV) or E80-7 (LV+) - Body ground Always 100 kΩ or higher
E162-6 (LG) or E80-16 (LG+) - Body ground Always 100 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE STEERING ACTUATOR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR