The speed sensor detects wheel speed and sends the appropriate signals to the ECU. These signals are used to control the Multi-terrain ABS, EBD, BA, VSC, A-TRC, CRAWL and hill-start assist control systems. This speed sensor contains a sensor IC, which consists of 2 MREs (Magnetic Resistance Element). The speed sensor rotor, which consists of 48 sets of N and S poles that are arranged in a circle, is integrated with the inner race of the hub bearing.
To detect the rotation direction, the output waves are used to determine the relationship of the pulses that are generated by 2 MREs. Upon receiving this signal, the sensor IC outputs a forward or backward wave to the skid control ECU.
| DTC Code | DTC Detection Condition | Trouble Area |
|---|---|---|
| C0210
C0215 |
When any of the following conditions is detected:
1.
At a vehicle speed of 10 km/h (6 mph) or more, the pulses are not input for 1 second. 2.
A momentary interruption of the speed sensor signal occurs at least 255 times when switching the ignition switch to ON and off. 3.
Continuous noise occurs in the speed sensor signals at a vehicle speed of 20 km/h (12 mph) or more. 4.
The speed sensor signal circuit is open for 0.12 seconds or more. |
·
Rear speed sensor RH ·
Rear speed sensor LH ·
Harness or connector ·
Speed sensor rotor ·
Sensor installation ·
Skid control ECU (Master cylinder solenoid) |
| C1238
C1239 |
Noise in the speed sensor signals occurs 75 times or more for 5 seconds when the vehicle speed is 20 km/h (12 mph) or more. | ·
Rear speed sensor RH ·
Rear speed sensor LH ·
Speed sensor rotor ·
Sensor installation ·
Skid control ECU (Master cylinder solenoid) |
DTC C0210 and C1238 are for the rear speed sensor RH.
DTC C0215 and C1239 are for the rear speed sensor LH.
When replacing the master cylinder solenoid, perform zero point calibration (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Chassis / ABS/VSC/TRC / Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| RR Speed Open | Rear speed sensor RH open circuit detection/Error or Normal | Normal | - |
| RL Speed Open | Rear speed sensor LH open circuit detection/Error or Normal | Normal | - |
Check for any momentary interruption in the wire harness and connector corresponding to the DTC (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CHECK FOR INTERMITTENT PROBLEMS).
There are no momentary interruptions.
Perform the above inspection before removing the sensor and connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check that there is no difference between the speed value output from the speed sensor displayed on the GTS and the speed value displayed on the speedometer when driving the vehicle.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| RR Wheel Speed | Rear speed sensor RH reading/min.: 0 km/h (0 mph), max.: 326 km/h (202 mph) | Actual wheel speed | No large fluctuations when driving at a constant speed. |
| RL Wheel Speed | Rear speed sensor LH reading/min.: 0 km/h (0 mph), max.: 326 km/h (202 mph) | Actual wheel speed | No large fluctuations when driving at a constant speed. |
The speed value output from the speed sensor displayed on the GTS is the same as the actual vehicle speed.
Check that the sensor signal conforms to the wheel direction.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| RR Wheel Direction | Rear wheel direction RH / Forward or Back | Forward: Forward
Back: Back |
- |
| RL Wheel Direction | Rear wheel direction LH / Forward or Back | Forward: Forward
Back: Back |
- |
The wheel direction is displayed correctly.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check if test mode (signal check) DTCs are output.
Enter the following menus: Chassis / ABS/VSC/TRC / Utility / Signal Check.
| Result | Proceed to |
|---|---|
| Test mode (signal check) DTC is output. | A |
| Test mode (signal check) DTC is not output. | B |
A
B
Check the speed sensor installation.
The installation nut is tightened properly.
There is no clearance between the sensor and rear axle.
| *1 | Rear Speed Sensor |
| *a | No clearance |
| *b | OK |
| *c | NG |
Check the speed sensor signal after replacement (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE).
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the rear speed sensor (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>REAR SPEED SENSOR>REMOVAL).
Check the sensor tip.
No scratches or foreign matter on the sensor tip.
Check the speed sensor signal after cleaning/replacement (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE).
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Install the rear speed sensor.
Disconnect the z19 and/or z20 rear speed sensor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| z19-2 (RR+) - Body ground | Ignition switch off | 10 kΩ or higher |
| z19-1 (RR-) - Body ground | Ignition switch off | 10 kΩ or higher |
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| z20-2 (RL+) - Body ground | Ignition switch off | 10 kΩ or higher |
| z20-1 (RL-) - Body ground | Ignition switch off | 10 kΩ or higher |
| *A | for RH |
| *B | for LH |
| *a | Component without harness connected
(Rear Speed Sensor) |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *A | for RH | *B | for LH |
| *1 | Skid Control Sensor Wire | - | - |
Remove the skid control sensor wire.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>REAR SPEED SENSOR>REMOVAL
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Nz1-4 - z19-2 (RR+) | Always | Below 1 Ω |
| Nz1-3 - z19-1 (RR-) | Always | Below 1 Ω |
| Nz1-4 - Nz1-3 | Always | 10 kΩ or higher |
| Nz1-4 - Nz1-1 | Always | 10 kΩ or higher |
| Nz1-4 - Nz1-2 | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Nz1-2 - z20-2 (RL+) | Always | Below 1 Ω |
| Nz1-1 - z20-1 (RL-) | Always | Below 1 Ω |
| Nz1-2 - Nz1-1 | Always | 10 kΩ or higher |
| Nz1-2 - Nz1-3 | Always | 10 kΩ or higher |
| Nz1-2 - Nz1-4 | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the A24 skid control ECU connector and Nz1 skid control sensor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A24-5 (RR+) - Nz1-4 (RR+) | Always | Below 1 Ω |
| A24-5 (RR+) - Body ground | Always | 10 kΩ or higher |
| A24-19 (RR-) - Nz1-3 (RR-) | Always | Below 1 Ω |
| A24-19 (RR-) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A24-20 (RL+) - Nz1-2 (RL+) | Always | Below 1 Ω |
| A24-20 (RL+) - Body ground | Always | 10 kΩ or higher |
| A24-6 (RL-) - Nz1-1 (RL-) | Always | Below 1 Ω |
| A24-6 (RL-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the A24 skid control ECU connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| Nz1-4 (RR+) - Body ground | Ignition switch ON | 11 to 14 V |
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| Nz1-2 (RL+) - Body ground | Ignition switch ON | 11 to 14 V |
| *a | Front view of wire harness connector
(to Skid Control Sensor Wire) |
| Result | Proceed to | |
|---|---|---|
| OK | A | |
| NG | LHD | B |
| RHD | C | |
A
B
C
Clear the DTCs (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).
Drive the vehicle at a speed of approximately 32 km/h (20 mph) or more for 60 seconds or more.
Check if the same DTCs are output (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).
Reinstall the sensors, connectors, etc. and restore the previous vehicle conditions before rechecking for DTCs.
| Result | Proceed to |
|---|---|
| DTC is output. | A |
| DTC is not output. | B |
A
B
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
Replace the rear speed sensor (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>REAR SPEED SENSOR>REMOVAL).
Check the speed sensor signal after replacement (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE).
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).
Drive the vehicle at a speed of approximately 32 km/h (20 mph) or more for 60 seconds or more.
Check if the same DTCs are output (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).
Reinstall the sensors, connectors, etc. and restore the previous vehicle conditions before rechecking for DTCs.
| Result | Proceed to |
|---|---|
| DTC is output. | A |
| DTC is not output. | B |
A
B
Remove the rear axle hub and bearing assembly (Click hereDrivetrain>AXLE AND DIFFERENTIAL>REAR AXLE SHAFT>DISASSEMBLY).
Check the sensor rotor.
No scratches, oil, or foreign matter on the rotors.
Check the speed sensor signal after cleaning/replacement (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE).
| Result | Proceed to | |
|---|---|---|
| NG | A | |
| OK | LHD | B |
| RHD | C | |
A
B
C