Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Start Function)
RM38G0E _58 Vehicle Interior _100610 THEFT DETERRENT / KEYLESS ENTRY _0467507 ENTRY AND START SYSTEM(for Start Function) C

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function)  B279F1C  Steering Lock Confirmation Signal Circuit Voltage Out of Range  


DESCRIPTION

This DTC is stored when the SLA input (the steering lock motor activation permission signal) sent directly from the certification ECU (smart key ECU assembly) to the steering lock ECU (steering lock actuator with ECU assembly) is determined to be abnormal.

HINT:

The steering lock ECU (steering lock actuator with ECU assembly) is not connected to the CAN communication system. However, the steering lock ECU (steering lock actuator with ECU assembly) is connected to the certification ECU (smart key ECU assembly) via LIN communication and communicates with other components via CAN communication through the certification ECU (smart key ECU assembly).


DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority Note
B279F1C Steering Lock Confirmation Signal Circuit Voltage Out of Range Either of the following conditions is met (1-trip detection logic*):
·

The steering lock motor activation command circuit has a short circuit.

·

The steering lock motor activation command circuit has an open circuit.


·

Steering lock ECU (steering lock actuator with ECU assembly)

·

Certification ECU (smart key ECU assembly)

·

Wire harness or connector


Entry&Start B DTC Output Confirmation Operation:

Any time



*: Only detected while a malfunction is present and the ignition switch is ON.


Vehicle Condition and Fail-safe Function when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Function when Malfunction Detected
The steering cannot be locked or unlocked. For this reason, the engine cannot be started. Prohibits the engine from being started (the engine does not start).

Related Data List and Active Test Items
DTC No. Data List and Active Test
B279F1C -

WIRING DIAGRAM

B586352E42
0.906,3.396 2.708,3.708 1.802,0.313 10 false : LIN Communication Line 5.552,2.635 7.063,2.99 1.51,0.354 10 false Certification ECU (Smart Key ECU Assembly) 5.552,2.469 6.177,2.75 0.625,0.281 10 false I39 5.958,0.75 6.542,0.958 0.583,0.208 10 false SLA1 5.781,0.75 6.125,1.073 0.344,0.323 10 false 3 2.531,0.74 2.875,1.063 0.344,0.323 10 false 6 2.177,0.75 2.521,1.073 0.344,0.323 10 false IG2 2.125,1.458 2.469,1.781 0.344,0.323 10 false GND 0.094,2.521 1.76,2.927 1.667,0.406 10 false I49 0.094,2.698 2.781,3.24 2.688,0.542 10 false Steering Lock ECU (Steering Lock Actuator with ECU Assembly) 2.521,1.344 2.865,1.667 0.344,0.323 10 false 1 1.188,0.896 1.531,1.219 0.344,0.323 10 false IC 6.427,0.208 6.771,0.531 0.344,0.323 10 false +B

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the ignition switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

The entry and start system (for Start Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before replacing the steering lock ECU (steering lock actuator with ECU assembly) or certification ECU (smart key ECU assembly), refer to Service Bulletin.

·

After performing repairs, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART




PROCEDURE

1.CHECK FOR DTC
a.

Using the GTS, check if LIN communication DTC B278588 is output.

Body Electrical > Entry&Start > Trouble Codes
50001 440
Result:
Result Proceed to
B278588 is not output A
B278588 is output B




A

2.CHECK HARNESS AND CONNECTOR (GROUND)

B

GO TO LIN COMMUNICATION SYSTEM (DTC B278588)

2.CHECK HARNESS AND CONNECTOR (GROUND)

Pre-procedure1

a.

Disconnect the I49 steering lock ECU (steering lock actuator with ECU assembly) connector.


Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I49)Location & Routing

Click Connector(I49)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Steering Lock Actuator or Upper Bracket Assembly

I49-1 (GND) - Body ground Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

c.

None



OK

3.CHECK STEERING LOCK ECU (STEERING LOCK ACTUATOR WITH ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK STEERING LOCK ECU (STEERING LOCK ACTUATOR WITH ECU ASSEMBLY)

Pre-procedure1

a.

Connect the I49 steering lock ECU (steering lock actuator with ECU assembly) connector.


Procedure1

b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(I49)Location & Routing

Click Connector(I49)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Steering Lock Actuator or Upper Bracket Assembly

I49-6 (IG2) - I49-1 (GND) Ignition switch off Below 1 V
I49-6 (IG2) - I49-1 (GND) Ignition switch ON 11 to 14 V


Result:
Proceed to
OK
NG



Post-procedure1

c.

None



OK

4.CLEAR DTC

NG

7.CHECK HARNESS AND CONNECTOR (STEERING LOCK ECU (STEERING LOCK ACTUATOR WITH ECU ASSEMBLY) - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
4.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Entry&Start > Clear DTCs
50002 440
Result:
Proceed to
NEXT




NEXT

5.CLEAR DATA LIST MALFUNCTION RECORD
5.CLEAR DATA LIST MALFUNCTION RECORD
a.

Disconnect the cable from the negative (-) battery terminal, wait for 30 seconds or more, and then reconnect the cable to the negative (-) battery terminal to clear the record of malfunctions stored in the Data List.

NOTICE:
·

After the ignition is turned off, there may be a waiting time before disconnecting the negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the battery

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART




Result:
Proceed to
NEXT




NEXT

6.CHECK FOR DTC
6.CHECK FOR DTC

Pre-procedure1

a.

Perform the DTC output confirmation operation.


Procedure1

b.

Check if DTC B279F1C is output.

Body Electrical > Entry&Start > Trouble Codes
50001 440
Result:
Result Proceed to
B279F1C is output A
B279F1C is not output B



Post-procedure1

c.

None



A

REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR WITH ECU ASSEMBLY)

B

SYSTEM RETURNED TO NORMAL (DTC STORED DUE TO BAD CONNECTION, BUT SYSTEM RETURNED TO NORMAL BY RECONNECTING CONNECTOR)

7.CHECK HARNESS AND CONNECTOR (STEERING LOCK ECU (STEERING LOCK ACTUATOR WITH ECU ASSEMBLY) - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))

Pre-procedure1

a.

Disconnect the I49 steering lock ECU (steering lock actuator with ECU assembly) connector.


b.

Disconnect the I39 certification ECU (smart key ECU assembly) connector.


Procedure1


Post-procedure1

d.

None



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR