Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Start Function)
RM38G0E _58 Vehicle Interior _100610 THEFT DETERRENT / KEYLESS ENTRY _0467507 ENTRY AND START SYSTEM(for Start Function) J

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function)  Steering Lock does not Lock  


DESCRIPTION

The steering lock ECU (steering lock actuator with ECU assembly) activates the steering lock motor and moves the lock bar into the steering column to lock the steering.

When the steering lock is operating, the steering may not lock when the lock bar is not aligned with the lock hole of the steering column. In this case, the steering can be locked by turning the steering wheel a little, as is done for a vehicle with a mechanical key, to change the position of the lock hole.

Related Data List and Active Test Items
Problem Symptom Data List and Active Test
Steering Lock does not Lock
Entry&Start
·

Steering Lock Request Receive

·

S Code Check

·

L Code Check


Main Body
·

FR Door Courtesy Switch Status

·

FL Door Courtesy Switch Status

·

RR Door Courtesy Switch Status

·

RL Door Courtesy Switch Status


Power Source Control
·

Shift P Signal



WIRING DIAGRAM

C396309E96
3.281,2.823 3.594,3.021 0.313,0.198 10 false 24 3.281,3.271 3.594,3.469 0.313,0.198 10 false 11 3.281,3.917 3.594,4.115 0.313,0.198 10 false 29 5.177,0.25 5.49,0.448 0.313,0.198 10 false 7 5.167,2.833 5.479,3.031 0.313,0.198 10 false 3 5.167,3.25 5.479,3.448 0.313,0.198 10 false 4 5.177,3.896 5.49,4.094 0.313,0.198 10 false 1 3.135,0.323 3.917,0.563 0.781,0.24 10 false from Battery 4.344,0.5 5.552,0.99 1.208,0.49 10 false STRG LOCK 0.208,2.688 1.792,3.156 1.583,0.469 10 false ID Code Box (Immobiliser Code ECU) 0.271,4.385 1.396,4.865 1.125,0.479 10 false Shift Lock Control Unit Assembly 2.125,4.396 2.583,4.594 0.458,0.198 10 false I39 2.115,4.563 3.656,5.104 1.542,0.542 10 false Certification ECU (Smart Key ECU Assembly) 4.438,4.427 4.896,4.625 0.458,0.198 10 false I49 4.438,4.583 7.125,5.073 2.688,0.49 10 false Steering Lock ECU (Steering Lock Actuator with ECU Assembly) 1.01,3.75 1.625,3.948 0.615,0.198 10 false P2 2.833,2.927 3.448,3.125 0.615,0.198 10 false SLR+ 2.896,3.365 3.208,3.531 0.313,0.167 10 false SLP 3.063,4 3.677,4.198 0.615,0.198 10 false E 5.375,0.354 5.99,0.552 0.615,0.198 10 false B 5.375,2.917 5.99,3.115 0.615,0.198 10 false IGE 5.375,3.354 5.99,3.552 0.615,0.198 10 false SLP1 5.375,4 5.99,4.198 0.615,0.198 10 false GND 2.438,3.76 2.677,3.948 0.24,0.188 10 false P 0.688,5.292 2.896,5.594 2.208,0.302 10 false : LIN Communication Line 2.177,3.635 2.635,3.833 0.458,0.198 10 false 14 1.292,3.646 1.75,3.906 0.458,0.26 10 false 1 0.281,4.229 0.896,4.427 0.615,0.198 10 false I35

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the ignition switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

Perform either of the following operations to lock/unlock the steering:

-

To unlock the steering, carry the electrical key transmitter sub-assembly and turn the ignition switch to ACC or ON.

-

To lock the steering, turn the ignition switch off with the shift lever in P, and then open a door.


·

Make sure that no DTCs are output. If any DTCs are output, proceed to Diagnostic Trouble Code Chart.

·

The entry and start system (for Start Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before replacing the steering lock ECU (steering lock actuator with ECU assembly) or certification ECU (smart key ECU assembly), refer to Service Bulletin.

·

After performing repairs, confirm that the problem does not recur.

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".



PROCEDURE

1.READ VALUE USING GTS (STEERING LOCK REQUEST RECEIVE)
a.

Read the Data List according to the display on the GTS.

Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Steering Lock Request Receive Status of steering lock command from certification ECU (smart key ECU assembly) OK or NG OK: Certification ECU (smart key ECU assembly) sends steering lock command (within 10 seconds of any door opened with the shift lever in P and ignition switch off)
NG: Certification ECU (smart key ECU assembly) does not send steering lock command (no door opened with the shift lever in P and ignition switch off)
If OK is not displayed even though the steering lock conditions are met, the certification ECU (smart key ECU assembly) may be malfunctioning.
Body Electrical > Entry&Start > Data List
Tester Display
Steering Lock Request Receive
50003 440 63
OK:

The certification ECU (smart key ECU assembly) receives a lock request signal within 10 seconds of turning the ignition switch from ON to ACC or off and opening a door with the shift lever in P, and OK is displayed on the GTS screen.



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING GTS (S CODE CHECK)

NG

10.READ VALUE USING GTS (DOOR COURTESY SWITCH STATUS)
2.READ VALUE USING GTS (S CODE CHECK)
a.

Read the Data List according to the display on the GTS.

Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
S Code Check Verification result between certification ECU (smart key ECU assembly) and ID code box (immobiliser code ECU) OK or NG OK: Verification result normal
NG: Verification result abnormal
When NG is displayed:
·

The ID code for the certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU) is not registered, or the certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU) is malfunctioning.

·

The steering cannot be locked.

·

The steering cannot be unlocked (the engine cannot be started).


Body Electrical > Entry&Start > Data List
Tester Display
S Code Check
50003 440 60
OK:

OK is displayed on the GTS.


HINT:

Reasons for verification failure:

·

The certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU) is malfunctioning.

·

There is a problem with the communication between ECUs.

·

An ECU was replaced, but not registered.

·

An ECU was replaced with an ECU which has already been registered to another vehicle.




Result:
Proceed to
OK
NG



OK

3.READ VALUE USING GTS (L CODE CHECK)

NG

9.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
3.READ VALUE USING GTS (L CODE CHECK)
a.

Read the Data List according to the display on the GTS.

Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
L Code Check Verification result between ID code box (immobiliser code ECU) and steering lock ECU (steering lock actuator with ECU assembly) OK or NG OK: Verification result normal
NG: Verification result abnormal
When NG is displayed:
·

The ID code for the ID code box (immobiliser code ECU) or steering lock ECU (steering lock actuator with ECU assembly) is not registered, or the ID code box (immobiliser code ECU) or steering lock ECU (steering lock actuator with ECU assembly) is malfunctioning.

·

The steering cannot be locked.

·

The steering cannot be unlocked (the engine cannot be started).


Body Electrical > Entry&Start > Data List
Tester Display
L Code Check
50003 440 61
OK:

OK is displayed on the GTS.


HINT:

Reasons for verification failure:

·

The steering lock ECU (steering lock actuator with ECU assembly) or certification ECU (smart key ECU assembly) is malfunctioning.

·

There is a problem with the communication between ECUs.

·

An ECU is replaced, but is not registered.

·

An ECU is replaced with an ECU which has a code already stored in it.




Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (POWER SOURCE)

NG

8.CHECK STEERING LOCK ECU (STEERING LOCK ACTUATOR WITH ECU ASSEMBLY)
4.CHECK HARNESS AND CONNECTOR (POWER SOURCE)
a.

Disconnect the I49 steering lock ECU (steering lock actuator with ECU assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I49)Location & Routing

Click Connector(I49)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Steering Lock Actuator or Upper Bracket Assembly

I49-1 (GND) - Body ground Always Below 1 Ω


NOTICE:

If the result is not as specified, check for looseness in the ground cable connection.



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(I49)Location & Routing

Click Connector(I49)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Steering Lock Actuator or Upper Bracket Assembly

I49-7 (B) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

5.CHECK STEERING LOCK ECU (STEERING LOCK ACTUATOR WITH ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK STEERING LOCK ECU (STEERING LOCK ACTUATOR WITH ECU ASSEMBLY)
a.
C396300C59
0.323,2.906 1.646,3.042 1.323,0.135 2.344,2.948 2.75,3.073 0.406,0.125 1.615,4.063 2.375,4.177 0.76,0.115 1.531,0.177 1.969,0.406 0.438,0.229 0.896,3.25 0.896,3.042 false 2.573,3.281 2.573,3.073 false 2.01,4.063 2.01,3.854 false 0.813,1.802 1.875,1.104 true 2.792,1.646 2.302,1.083 true 0.271,0.26 0.583,0.417 0.313,0.156 10 false *a 0.823,3.281 1.135,3.438 0.313,0.156 10 false *c 1.917,3.688 2.229,3.844 0.313,0.156 10 false *d 2.5,3.302 2.813,3.458 0.313,0.156 10 false *c 0.646,1.854 1.104,2.052 0.458,0.198 10 false IGE 2.76,1.698 3.219,1.896 0.458,0.198 10 false GND 2.969,4.083 3.427,4.281 0.458,0.198 10 false GND 1.635,0.208 2.094,0.406 0.458,0.198 10 false I49 0.083,2.458 0.396,2.615 0.313,0.156 10 false *b
*a Component with harness connected
(Steering Lock ECU (Steering Lock Actuator with ECU Assembly))
*b Waveform
*c Steering lock motor not operating
*d Steering lock motor operating


Connect the I49 steering lock ECU (steering lock actuator with ECU assembly) connector.


b.

Check the signal waveform according to the condition(s) in the table below.

Tester Connection Condition Tool Setting Specified Condition

Click Location & Routing(I49)Location & Routing

Click Connector(I49)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Steering Lock Actuator or Upper Bracket Assembly

I49-3 (IGE) - I49-1 (GND) Steering lock motor operating when all conditions met, and then door opened:
·

Shift lever in P

·

Steering unlocked

·

Ignition switch turned off


2 V/DIV., 200 ms./DIV. Pulse generation
(See waveform)


Result:
Proceed to
OK
NG



OK

REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR WITH ECU ASSEMBLY)

NG

6.CHECK HARNESS AND CONNECTOR (STEERING LOCK ECU (STEERING LOCK ACTUATOR WITH ECU ASSEMBLY) - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
6.CHECK HARNESS AND CONNECTOR (STEERING LOCK ECU (STEERING LOCK ACTUATOR WITH ECU ASSEMBLY) - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
a.

Disconnect the I49 steering lock ECU (steering lock actuator with ECU assembly) connector.


b.

Disconnect the I39 certification ECU (smart key ECU assembly) connector.



Result:
Proceed to
OK
NG



OK

7.CHECK STEERING LOCK ECU (STEERING LOCK ACTUATOR WITH ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK STEERING LOCK ECU (STEERING LOCK ACTUATOR WITH ECU ASSEMBLY)
a.
C342409C74
1.531,0.844 2.01,1.125 0.479,0.281 1.917,1.938 2.667,2.656 true 0.188,0.167 0.5,0.323 0.313,0.156 10 false *a 1.646,0.896 1.958,1.052 0.313,0.156 10 false I49 2.615,2.708 2.917,2.885 0.302,0.177 10 false IGE
*a Component with harness connected
(Steering Lock ECU (Steering Lock Actuator with ECU Assembly))


Connect the I49 steering lock ECU (steering lock actuator with ECU assembly) connector.


b.

Connect the I39 certification ECU (smart key ECU assembly) connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(I49)Location & Routing

Click Connector(I49)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Steering Lock Actuator or Upper Bracket Assembly

I49-3 (IGE) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR WITH ECU ASSEMBLY)

8.CHECK STEERING LOCK ECU (STEERING LOCK ACTUATOR WITH ECU ASSEMBLY)
a.

Replace the steering lock ECU (steering lock actuator with ECU assembly) with a new one and perform registration.

HINT:
·

For registration.

Refer to Service Bulletin.




b.

Read the Data List according to the display on the GTS.

Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
L Code Check Verification result between ID code box (immobiliser code ECU) and steering lock ECU (steering lock actuator with ECU assembly) OK or NG OK: Verification result normal
NG: Verification result abnormal
When NG is displayed:
·

The ID code for the ID code box (immobiliser code ECU) or steering lock ECU (steering lock actuator with ECU assembly) is not registered, or the ID code box (immobiliser code ECU) or steering lock ECU (steering lock actuator with ECU assembly) is malfunctioning.

·

The steering cannot be locked.

·

The steering cannot be unlocked (the engine cannot be started).


Body Electrical > Entry&Start > Data List
Tester Display
L Code Check
50003 440 61
OK:

OK is displayed on the GTS.



Result:
Proceed to
OK
NG



OK

END (STEERING LOCK ECU (STEERING LOCK ACTUATOR WITH ECU ASSEMBLY) WAS DEFECTIVE)

NG

REPLACE ID CODE BOX (IMMOBILISER CODE ECU)

9.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Replace the certification ECU (smart key ECU assembly) with a new one and perform registration.

HINT:

Refer to Service Bulletin.



b.

Read the Data List according to the display on the GTS.

Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
S Code Check Verification result between certification ECU (smart key ECU assembly) and ID code box (immobiliser code ECU) OK or NG OK: Verification result normal
NG: Verification result abnormal
When NG is displayed:
·

The ID code for the certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU) is not registered, or the certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU) is malfunctioning.

·

The steering cannot be locked.

·

The steering cannot be unlocked (the engine cannot be started).


Body Electrical > Entry&Start > Data List
Tester Display
S Code Check
50003 440 60
OK:

OK is displayed on the GTS.



Result:
Proceed to
OK
NG



OK

END (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) WAS DEFECTIVE)

NG

REPLACE ID CODE BOX (IMMOBILISER CODE ECU)

10.READ VALUE USING GTS (DOOR COURTESY SWITCH STATUS)
a.

Using the GTS, check the following main body ECU (multiplex network body ECU) Data List item by opening and closing each door to confirm the state of each door courtesy light switch assembly.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
FR Door Courtesy Switch Status Front door RH courtesy light switch signal OFF or ON OFF: Front door RH closed
ON: Front door RH open
-
FL Door Courtesy Switch Status Front door LH courtesy light switch signal OFF or ON OFF: Front door LH closed
ON: Front door LH open
-
RR Door Courtesy Switch Status Rear door RH courtesy light switch signal OFF or ON OFF: Rear door RH closed
ON: Rear door RH open
-
RL Door Courtesy Switch Status Rear door LH courtesy light switch signal OFF or ON OFF: Rear door LH closed
ON: Rear door LH open
-
Body Electrical > Main Body > Data List
Tester Display
FR Door Courtesy Switch Status
FL Door Courtesy Switch Status
RR Door Courtesy Switch Status
RL Door Courtesy Switch Status
50003 449 30,31,32,33
OK:

The Data List item changes in accordance with the opening and closing of each door.



Result:
Proceed to
OK
NG



OK

11.READ VALUE USING GTS (SHIFT P SIGNAL)

NG

GO TO LIGHTING SYSTEM (Front Door Courtesy Switch Circuit, Rear Door Courtesy Switch Circuit)

11.READ VALUE USING GTS (SHIFT P SIGNAL)
a.

Move the shift lever to P.


b.

Read the Data List according to the display on the GTS.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Shift P Signal Shift position P OFF or ON OFF: Shift lever not in P
ON: Shift lever in P
·

Use this item to determine if the shift position switch is malfunctioning.

·

The engine cannot be started when this item is OFF.


Body Electrical > Power Source Control > Data List
Tester Display
Shift P Signal
50003 454 205
OK:

ON is displayed on the GTS.



Result:
Proceed to
OK
NG



OK

12.READ VALUE USING GTS (STEERING LOCK REQUEST RECEIVE)

NG

13.CHECK SHIFT LOCK CONTROL UNIT ASSEMBLY
12.READ VALUE USING GTS (STEERING LOCK REQUEST RECEIVE)
a.

Replace the certification ECU (smart key ECU assembly) with a new one and perform registration.

HINT:

Refer to Service Bulletin.



b.

Read the Data List according to the display on the GTS.

Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Steering Lock Request Receive Status of steering lock command from certification ECU (smart key ECU assembly) OK or NG OK: Certification ECU (smart key ECU assembly) sends steering lock command (within 10 seconds of any door opened with the shift lever in P and ignition switch off)
NG: Certification ECU (smart key ECU assembly) does not send steering lock command (no door opened with the shift lever in P and ignition switch off)
If OK is not displayed even though the steering lock conditions are met, the certification ECU (smart key ECU assembly) may be malfunctioning.
Body Electrical > Entry&Start > Data List
Tester Display
Steering Lock Request Receive
50003 440 63
OK:

Within 10 seconds after any of the doors is opened with the shift lever in P and ignition switch off, the Data List item changes to "OK".



Result:
Proceed to
OK
NG



OK

END (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) WAS DEFECTIVE)

NG

REPLACE ID CODE BOX (IMMOBILISER CODE ECU)

13.CHECK SHIFT LOCK CONTROL UNIT ASSEMBLY
a.
B574624C62
1.583,0.042 1.979,0.25 0.396,0.208 2.271,1.885 2.146,1.885 2.146,1.885 1.698,0.792 true 0.146,0.083 0.458,0.281 0.313,0.198 10 false *a 1.656,0.063 2.115,0.26 0.458,0.198 10 false I39 2.333,1.802 2.698,1.99 0.365,0.188 10 false P
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(I39)Location & Routing

Click Connector(I39)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Certification ECU

I39-14 (P) - Body ground Shift lever in P → Shift lever not in P 9 V or higher → 2.76 V or less



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

14.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - SHIFT LOCK CONTROL UNIT ASSEMBLY)
14.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - SHIFT LOCK CONTROL UNIT ASSEMBLY)
a.

Disconnect the I39 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the I35 shift lock control unit assembly connector.



d.

Reconnect the I39 certification ECU (smart key ECU assembly) connector.


Result:
Proceed to
OK
NG



OK

15.CHECK SHIFT LOCK CONTROL UNIT ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

15.CHECK SHIFT LOCK CONTROL UNIT ASSEMBLY
a.
B574624C63
1.583,0.042 1.979,0.25 0.396,0.208 2.271,1.885 2.146,1.885 2.146,1.885 1.698,0.792 true 0.125,0.083 0.438,0.281 0.313,0.198 10 false *a 1.698,0.063 2.083,0.26 0.385,0.198 10 false I39 2.333,1.802 2.698,1.99 0.365,0.188 10 false P
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(I39)Location & Routing

Click Connector(I39)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Certification ECU

I39-14 (P) - Body ground Shift lever in P 9 V or higher



Result:
Proceed to
OK
NG



OK

NG

REPLACE SMART KEY ECU ASSEMBLY