Home › Vehicle Interior › SEAT › FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)
RM38G0E _58 Vehicle Interior _100628 SEAT _0467514 FRONT POWER SEAT CONTROL SYSTEM(w/ Memory) J

SEAT  FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)  Wireless-linked Return Function does not Operate  


DESCRIPTION

When a door is unlocked using the wireless unlock function, the certification ECU (smart key ECU assembly) sends a key ID signal to the main body ECU (multiplex network body ECU). When a door is unlocked using the entry unlock function, the certification ECU (smart key ECU assembly) sends a door unlock signal and key ID signal to the main body ECU (multiplex network body ECU). When the main body ECU (multiplex network body ECU) receives the door unlock signal, it stores the key ID. When the driver door is opened, the memory call information of the stored key ID is sent to each driving position related control ECU. Each control ECU receives the information and then performs the memory call operation according to predetermined control timing values.

CAUTION / NOTICE / HINT

NOTICE:
·

The seat position will not be stored if the SET switch and 2 or more of the seat memory switches (for example, M1 switch and M2 switch) are pressed simultaneously.

If a memorizing operation has failed, release all of the switches. The seat memory function will not operate unless the switches are released.

·

Before replacing the main body ECU (multiplex network body ECU) or certification ECU (smart key ECU assembly), refer to Service Bulletin.



PROCEDURE

1.CHECK FRONT POWER SEAT OPERATION
a.

b.

c.

Check the seat position restoration function.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)>OPERATION CHECK


d.

Check the operation of memory registration of the memory call function.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)>OPERATION CHECK

Result:
Result Proceed to
OK A
NG (Power seat operation) B
NG (Seat position memory function) C
NG (Seat position restoration function) D
NG (Memory registration) E




A

2.CHECK MEMORY CALL FUNCTION (MEMORY REGISTRATION AND AUTOMATIC MEMORY CALL FUNCTION)

B

C

GO TO OTHER DIAGNOSIS PROCEDURE (Power Seat Position is not Memorized)

D

GO TO OTHER DIAGNOSIS PROCEDURE (Power Seat does not Return to Memorized Position)

E

GO TO OTHER DIAGNOSIS PROCEDURE (Wireless Transmitter Memory Function does not Operate)

2.CHECK MEMORY CALL FUNCTION (MEMORY REGISTRATION AND AUTOMATIC MEMORY CALL FUNCTION)
a.

Check the memory registration and automatic memory call function of the memory call function.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)>OPERATION CHECK

Result:
Result Proceed to
Memory call function linked with the wireless unlock function does not operate. A
Memory call function linked with the entry unlock function does not operate. B
Memory call function linked with the wireless unlock function and entry unlock function both do not operate. C




A

3.CHECK WIRELESS DOOR LOCK CONTROL SYSTEM

B

6.CHECK SMART ENTRY AND START SYSTEM (for Entry Function)

C

9.READ VALUE USING GTS (MEMORY CALL REGISTRATION)
3.CHECK WIRELESS DOOR LOCK CONTROL SYSTEM
a.

Check the wireless unlock function of the wireless door lock control system.

Click hereVehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM>OPERATION CHECK

OK:

Wireless unlock function is normal.



Result:
Proceed to
OK
NG



OK

4.REPLACE POSITION CONTROL ECU ASSEMBLY

NG

4.REPLACE POSITION CONTROL ECU ASSEMBLY
a.

Replace the position control ECU assembly with a new or known good one.

Click hereVehicle Interior>SEAT>POWER SEAT CONTROL ECU (for Front Seat)>REMOVAL


Result:
Proceed to
NEXT



NEXT

5.CHECK MEMORY CALL FUNCTION (MEMORY REGISTRATION AND AUTOMATIC MEMORY CALL FUNCTION)
5.CHECK MEMORY CALL FUNCTION (MEMORY REGISTRATION AND AUTOMATIC MEMORY CALL FUNCTION)
a.

Check the memory registration and automatic memory call function of the memory call function.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)>OPERATION CHECK

OK:

Memory call function linked with the wireless unlock function operates normally.



Result:
Proceed to
OK
NG



OK

END (POSITION CONTROL ECU ASSEMBLY WAS DEFECTIVE)

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

6.CHECK SMART ENTRY AND START SYSTEM (for Entry Function)

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK

OK:

Entry unlock function is normal.


Result:
Proceed to
OK
NG



OK

7.REPLACE POSITION CONTROL ECU ASSEMBLY

NG

7.REPLACE POSITION CONTROL ECU ASSEMBLY
a.

Replace the position control ECU assembly with a new or known good one.

Click hereVehicle Interior>SEAT>POWER SEAT CONTROL ECU (for Front Seat)>REMOVAL


Result:
Proceed to
NEXT



NEXT

8.CHECK MEMORY CALL FUNCTION (MEMORY REGISTRATION AND AUTOMATIC MEMORY CALL FUNCTION)
8.CHECK MEMORY CALL FUNCTION (MEMORY REGISTRATION AND AUTOMATIC MEMORY CALL FUNCTION)
a.

Check the memory registration and automatic memory call function of the memory call function.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)>OPERATION CHECK

OK:

Memory call function linked with the entry unlock function operates normally.



Result:
Proceed to
OK
NG



OK

END (POSITION CONTROL ECU ASSEMBLY WAS DEFECTIVE)

NG

9.READ VALUE USING GTS (MEMORY CALL REGISTRATION)
a.

Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
MEM Switch No. with Key ID 1 Memory switch linked with key ID1 NONE, D MEM SW1, D MEM SW2 or D MEM SW3 NONE: No switches linked with key ID1
D MEM SW1: M1 switch linked with key ID1
D MEM SW2: M2 switch linked with key ID1
D MEM SW3: M3 switch linked with key ID1
-
MEM Switch No. with Key ID 2 Memory switch linked with key ID2 NONE, D MEM SW1, D MEM SW2 or D MEM SW3 NONE: No switches linked with key ID2
D MEM SW1: M1 switch linked with key ID2
D MEM SW2: M2 switch linked with key ID2
D MEM SW3: M3 switch linked with key ID2
-
MEM Switch No. with Key ID 3 Memory switch linked with key ID3 NONE, D MEM SW1, D MEM SW2 or D MEM SW3 NONE: No switches linked with key ID3
D MEM SW1: M1 switch linked with key ID3
D MEM SW2: M2 switch linked with key ID3
D MEM SW3: M3 switch linked with key ID3
-
MEM Switch No. with Key ID 4 Memory switch linked with key ID4 NONE, D MEM SW1, D MEM SW2 or D MEM SW3 NONE: No switches linked with key ID4
D MEM SW1: M1 switch linked with key ID4
D MEM SW2: M2 switch linked with key ID4
D MEM SW3: M3 switch linked with key ID4
-
MEM Switch No. with Key ID 5 Memory switch linked with key ID5 NONE, D MEM SW1, D MEM SW2 or D MEM SW3 NONE: No switches linked with key ID5
D MEM SW1: M1 switch linked with key ID5
D MEM SW2: M2 switch linked with key ID5
D MEM SW3: M3 switch linked with key ID5
-
MEM Switch No. with Key ID 6 Memory switch linked with key ID6 NONE, D MEM SW1, D MEM SW2 or D MEM SW3 NONE: No switches linked with key ID6
D MEM SW1: M1 switch linked with key ID6
D MEM SW2: M2 switch linked with key ID6
D MEM SW3: M3 switch linked with key ID6
-
MEM Switch No. with Key ID 7 Memory switch linked with key ID7 NONE, D MEM SW1, D MEM SW2 or D MEM SW3 NONE: No switches linked with key ID7
D MEM SW1: M1 switch linked with key ID7
D MEM SW2: M2 switch linked with key ID7
D MEM SW3: M3 switch linked with key ID7
-
Body Electrical > Main Body > Data List
Tester Display
MEM Switch No. with Key ID 1
MEM Switch No. with Key ID 2
MEM Switch No. with Key ID 3
MEM Switch No. with Key ID 4
MEM Switch No. with Key ID 5
MEM Switch No. with Key ID 6
MEM Switch No. with Key ID 7
50003 449 160,161,162,163,164,165,166

b.

Enter the following menus: Body Electrical / Driver Seat / Data List.


c.

Read the Data List according to the display on the GTS.

Body Electrical > Driver Seat > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Memory No1 Seat position memorized with M1 switch Mem or Not Mem Mem: Memorized
Not Mem: Not memorized
-
Memory No2 Seat position memorized with M2 switch Mem or Not Mem Mem: Memorized
Not Mem: Not memorized
-
Memory No3 Seat position memorized with M3 switch Mem or Not Mem Mem: Memorized
Not Mem: Not memorized
-
Body Electrical > Driver Seat > Data List
Tester Display
Memory No1
Memory No2
Memory No3
50003 162 700,701,702
OK:

A seat position has been memorized for the seat position memory switch linked to the electrical key transmitter sub-assembly. (For example, the value of "Mem Switch No. with Key ID1" is D MEM SW1 and the value of "Seat Memory No1" is Mem.)



Result:
Proceed to
OK
NG



OK

10.READ VALUE USING GTS (FRONT DOOR COURTESY SWITCH STATUS)

NG

10.READ VALUE USING GTS (FRONT DOOR COURTESY SWITCH STATUS)
a.

Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
FR Door Courtesy Switch Status Front door courtesy light switch assembly (RH) signal Close or Open Close: Front door RH closed
Open: Front door RH open
for RHD
FL Door Courtesy Switch Status Front door courtesy light switch assembly (LH) signal Close or Open Close: Front door LH closed
Open: Front door LH open
for LHD
Body Electrical > Main Body > Data List
Tester Display
FR Door Courtesy Switch Status
50003 449 30
OK:

On the GTS screen, Close or Open is displayed accordingly.



Result:
Proceed to
OK
NG



OK

11.REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

GO TO LIGHTING SYSTEM (Door Courtesy Switch Circuit)

11.REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
a.

Replace the main body ECU (multiplex network body ECU) with a new or known good one.

for LHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL

for RHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL


Result:
Proceed to
NEXT



NEXT

12.CHECK MEMORY CALL FUNCTION (MEMORY REGISTRATION AND AUTOMATIC MEMORY CALL FUNCTION)
12.CHECK MEMORY CALL FUNCTION (MEMORY REGISTRATION AND AUTOMATIC MEMORY CALL FUNCTION)
a.

Check the memory registration and automatic memory call function of the memory call function.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)>OPERATION CHECK

OK:

Memory call functions linked with the wireless unlock function and entry unlock function operate normally.



Result:
Proceed to
OK
NG



OK

END (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) WAS DEFECTIVE)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)