Home › Vehicle Interior › SEAT › FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)
RM38G0E _58 Vehicle Interior _100628 SEAT _0467514 FRONT POWER SEAT CONTROL SYSTEM(w/ Memory) J

SEAT  FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)  Wireless Transmitter Memory Function does not Operate  


DESCRIPTION

With the ignition switch ON and the driver door closed, pressing the manual lock or unlock switch on the multiplex network master switch assembly while holding a seat memory switch (M1, M2 or M3 switch) will register the transmitter recognition code into the seat memory switch that was pressed. After registration is completed, the answer back buzzer sounds.

CAUTION / NOTICE / HINT

NOTICE:
·

The seat position will not be stored if the SET switch and 2 or more of the seat memory switches (for example, M1, M2 or M3 switch) are pressed simultaneously.

If a memorizing operation has failed, release all of the switches. The seat memory function will not operate unless the switches are released.

·

The seat will not return to the memorized position if 2 or more of the seat memory switches (for example, M1, M2 or M3 switch) are pressed simultaneously.

If a restoring operation has failed, release all of the switches. The seat memory restoring function will not operate unless the switches are released.

·

The front power seat control system (w/ Memory) uses the CAN communication system. First, confirm that there are no malfunctions in the CAN communication system. Refer to How to Proceed with Troubleshooting.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before replacing the main body ECU (multiplex network body ECU) or certification ECU (smart key ECU assembly), refer to Service Bulletin.



PROCEDURE

1.CHECK POWER DOOR LOCK CONTROL SYSTEM
a.

Check the manual lock/unlock function by using the door control switch (multiplex network master switch assembly).

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK

OK:

Manual lock/unlock function operates normally.



Result:
Proceed to
OK
NG



OK

2.CHECK SMART ENTRY AND START SYSTEM (for Start Function)

NG

2.CHECK SMART ENTRY AND START SYSTEM (for Start Function)
a.

Check that the engine starts operates normally when the ignition switch is pressed while carrying the electrical key transmitter sub-assembly and with the brake pedal depressed.

OK:

Engine starts normally.



Result:
Proceed to
OK
NG



OK

3.CHECK SEAT POSITION MEMORY AND RESTORING FUNCTION

NG

3.CHECK SEAT POSITION MEMORY AND RESTORING FUNCTION
a.

Check the seat position memory and restoring functions.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)>OPERATION CHECK

Result:
Result Proceed to
OK A
NG (Seat position memory function does not operate normally) B
NG (Seat position restoring function does not operate normally) C




A

4.READ VALUE USING GTS (FRONT DOOR COURTESY SWITCH STATUS)

B

GO TO OTHER DIAGNOSIS PROCEDURE (Power Seat Position is not Memorized)

C

GO TO OTHER DIAGNOSIS PROCEDURE (Power Seat does not Return to Memorized Position)

4.READ VALUE USING GTS (FRONT DOOR COURTESY SWITCH STATUS)
a.

Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
FR Door Courtesy Switch Status Front door courtesy light switch assembly (RH) signal Close or Open Close: Front door RH closed
Open: Front door RH open
for RHD
FL Door Courtesy Switch Status Front door courtesy light switch assembly (LH) signal Close or Open Close: Front door LH closed
Open: Front door LH open
for LHD
Body Electrical > Main Body > Data List
Tester Display
FR Door Courtesy Switch Status
FL Door Courtesy Switch Status
50003 449 30,31
OK:

On the GTS screen, ON or OFF is displayed accordingly.



Result:
Proceed to
OK
NG



OK

5.CHECK MEMORY CALL FUNCTION (MEMORY REGISTRATION)

NG

GO TO LIGHTING SYSTEM (Front Door Courtesy Switch Circuit)

5.CHECK MEMORY CALL FUNCTION (MEMORY REGISTRATION)
a.

Check the memory registration of the memory call function.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)>OPERATION CHECK

OK:

A seat position can be registered normally.



Result:
Proceed to
OK
NG



OK

6.READ VALUE USING GTS (MEMORY CALL REGISTRATION)

NG

8.REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
6.READ VALUE USING GTS (MEMORY CALL REGISTRATION)
a.

Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
MEM Switch No. with Key ID 1 Memory switch linked with key ID1 NONE, D MEM SW1, D MEM SW2 or D MEM SW3 NONE: No switches linked with key ID1
D MEM SW1: M1 switch linked with key ID1
D MEM SW2: M2 switch linked with key ID1
D MEM SW3: M3 switch linked with key ID1
-
MEM Switch No. with Key ID 2 Memory switch linked with key ID2 NONE, D MEM SW1, D MEM SW2 or D MEM SW3 NONE: No switches linked with key ID2
D MEM SW1: M1 switch linked with key ID2
D MEM SW2: M2 switch linked with key ID2
D MEM SW3: M3 switch linked with key ID2
-
MEM Switch No. with Key ID 3 Memory switch linked with key ID3 NONE, D MEM SW1, D MEM SW2 or D MEM SW3 NONE: No switches linked with key ID3
D MEM SW1: M1 switch linked with key ID3
D MEM SW2: M2 switch linked with key ID3
D MEM SW3: M3 switch linked with key ID3
-
MEM Switch No. with Key ID 4 Memory switch linked with key ID4 NONE, D MEM SW1, D MEM SW2 or D MEM SW3 NONE: No switches linked with key ID4
D MEM SW1: M1 switch linked with key ID4
D MEM SW2: M2 switch linked with key ID4
D MEM SW3: M3 switch linked with key ID4
-
MEM Switch No. with Key ID 5 Memory switch linked with key ID5 NONE, D MEM SW1, D MEM SW2 or D MEM SW3 NONE: No switches linked with key ID5
D MEM SW1: M1 switch linked with key ID5
D MEM SW2: M2 switch linked with key ID5
D MEM SW3: M3 switch linked with key ID5
-
MEM Switch No. with Key ID 6 Memory switch linked with key ID6 NONE, D MEM SW1, D MEM SW2 or D MEM SW3 NONE: No switches linked with key ID6
D MEM SW1: M1 switch linked with key ID6
D MEM SW2: M2 switch linked with key ID6
D MEM SW3: M3 switch linked with key ID6
-
MEM Switch No. with Key ID 7 Memory switch linked with key ID7 NONE, D MEM SW1, D MEM SW2 or D MEM SW3 NONE: No switches linked with key ID7
D MEM SW1: M1 switch linked with key ID7
D MEM SW2: M2 switch linked with key ID7
D MEM SW3: M3 switch linked with key ID7
-
Body Electrical > Main Body > Data List
Tester Display
MEM Switch No. with Key ID 1
MEM Switch No. with Key ID 2
MEM Switch No. with Key ID 3
MEM Switch No. with Key ID 4
MEM Switch No. with Key ID 5
MEM Switch No. with Key ID 6
MEM Switch No. with Key ID 7
50003 449 160,161,162,163,164,165,166
OK:

A seat position memory switch is linked to the electrical key transmitter sub-assembly.



Result:
Proceed to
OK
NG



OK

7.CHECK MEMORY CALL FUNCTION (MEMORY REGISTRATION AND AUTOMATIC MEMORY CALL FUNCTION)

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

7.CHECK MEMORY CALL FUNCTION (MEMORY REGISTRATION AND AUTOMATIC MEMORY CALL FUNCTION)
a.

Check the memory registration and automatic memory call function of the memory call function.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)>OPERATION CHECK

OK:

A seat position can be registered and the automatic memory call function operates normally.



Result:
Proceed to
OK
NG



OK

NG

GO TO OTHER DIAGNOSIS PROCEDURE (Wireless-linked Return Function does not Operate)

8.REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
a.

Replace the main body ECU (multiplex network body ECU) with a new or known good one.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL


Result:
Proceed to
NEXT



NEXT

9.CHECK MEMORY CALL FUNCTION (MEMORY REGISTRATION)
9.CHECK MEMORY CALL FUNCTION (MEMORY REGISTRATION)
a.

Check the memory registration of the memory call function.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)>OPERATION CHECK

OK:

A seat position can be registered normally.



Result:
Proceed to
OK
NG



OK

END (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) WAS DEFECTIVE)

NG

10.REPLACE POSITION CONTROL ECU ASSEMBLY
10.REPLACE POSITION CONTROL ECU ASSEMBLY
a.

Replace the position control ECU assembly with a new or known good one.

Click hereVehicle Interior>SEAT>POWER SEAT CONTROL ECU (for Front Seat)>REMOVAL


Result:
Proceed to
NEXT



NEXT

11.CHECK MEMORY CALL FUNCTION (MEMORY REGISTRATION)
11.CHECK MEMORY CALL FUNCTION (MEMORY REGISTRATION)
a.

Check the memory registration of the memory call function.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)>OPERATION CHECK

OK:

A seat position can be registered normally.



Result:
Proceed to
OK
NG



OK

END (POSITION CONTROL ECU ASSEMBLY WAS DEFECTIVE)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)