Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › 2021.04–2022.11
RM38G0E _57 Power Source / Network _100626 NETWORKING _0467519 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Check Bus 5 Line (for LHD)  


DESCRIPTION

Symptom Trouble Area

*1: w/ Reverse Shift-linked Mirror

*2: w/ Power Tilt and Power Telescopic Steering Column System

*3: w/ Headlight ECU

*4: w/ Seat Position Memory System

*5: w/ Power Back Door System

There are ECUs or sensors that display a communication stop on the bus diagnostic screen. Or, there are ECUs or sensors that store a communication stop history on the "Detail" screen.
·

CAN bus lines or connector

·

Central gateway ECU (network gateway ECU)

·

Outer mirror control ECU assembly LH*1

·

Outer mirror control ECU assembly RH*1

·

Multiplex tilt and telescopic ECU*2

·

Headlight ECU sub-assembly LH*3

·

Headlight ECU sub-assembly RH*3

·

Position control ECU assembly*4

·

Certification ECU (smart key ECU assembly)

·

Air conditioning amplifier assembly

·

Main body ECU (multiplex network body ECU)

·

Multiplex network door ECU*5

·

No. 3 global CAN junction connector

·

No. 4 global CAN junction connector

·

No. 11 global CAN junction connector



WIRING DIAGRAM

C445970E04
0.865,0.573 1.479,0.771 0.615,0.198 10 false CANH 0.875,1.146 1.49,1.344 0.615,0.198 10 false CANL 0.823,2.708 1.438,2.906 0.615,0.198 10 false CANP 0.823,3.198 1.438,3.396 0.615,0.198 10 false CANN 5.958,0.5 6.573,0.698 0.615,0.198 10 false CA5H 5.938,1.26 6.552,1.458 0.615,0.198 10 false CA5L 5.969,2.625 6.583,2.823 0.615,0.198 10 false CANP 5.958,3.198 6.573,3.396 0.615,0.198 10 false CANN 5.969,4.667 6.583,4.865 0.615,0.198 10 false CANH 5.969,5.24 6.583,5.438 0.615,0.198 10 false CANL 1.365,0.479 1.979,0.677 0.615,0.198 10 false 1 1.365,1.021 1.979,1.219 0.615,0.198 10 false 2 1.385,2.552 2,2.75 0.615,0.198 10 false 3 1.365,3.083 1.979,3.281 0.615,0.198 10 false 11 1.375,4.552 1.99,4.75 0.615,0.198 10 false 13 3.115,2.51 3.729,2.708 0.615,0.198 10 false 4 3.146,0.479 3.76,0.677 0.615,0.198 10 false 3 3.115,1.042 3.729,1.24 0.615,0.198 10 false 13 3.083,3.083 3.698,3.281 0.615,0.198 10 false 14 1.385,5.083 2,5.281 0.615,0.198 10 false 14 3.135,4.542 3.75,4.74 0.615,0.198 10 false 8 3.073,5.083 3.688,5.281 0.615,0.198 10 false 18 4.094,0.5 4.708,0.698 0.615,0.198 10 false 1 4.094,1.031 4.708,1.229 0.615,0.198 10 false 11 4.125,2.531 4.74,2.729 0.615,0.198 10 false 6 4.104,3.083 4.719,3.281 0.615,0.198 10 false 16 4.135,4.542 4.75,4.74 0.615,0.198 10 false 9 4.115,5.104 4.729,5.302 0.615,0.198 10 false 19 4.125,5.656 4.74,5.854 0.615,0.198 10 false 2 4.104,5.979 4.719,6.177 0.615,0.198 10 false 12 5.573,0.49 6.188,0.688 0.615,0.198 10 false 7 5.573,1.031 6.188,1.229 0.615,0.198 10 false 8 5.708,2.542 6.323,2.74 0.615,0.198 10 false 9 5.719,3.083 6.333,3.281 0.615,0.198 10 false 8 5.677,4.552 6.292,4.75 0.615,0.198 10 false 24 5.677,5.094 6.292,5.292 0.615,0.198 10 false 23 0.125,1.385 0.74,1.583 0.615,0.198 10 false I39 0.125,1.573 1.948,2.021 1.823,0.448 10 false Certification ECU (Smart Key ECU Assembly) 0.135,3.406 0.75,3.604 0.615,0.198 10 false I43 0.135,3.615 2.583,4 2.448,0.385 10 false Multiplex Tilt and Telescopic ECU*1 0.135,5.427 0.75,5.625 0.615,0.198 10 false i19 0.125,5.625 2.573,6.01 2.448,0.385 10 false Position Control ECU Assembly*4 5.49,1.385 6.104,1.583 0.615,0.198 10 false I42 5.198,1.594 7.125,2.01 1.927,0.417 10 false Central Gateway ECU (Network Gateway ECU) 5.552,3.438 6.167,3.635 0.615,0.198 10 false N1 5.531,3.625 7.083,4.052 1.552,0.427 10 false Outer Mirror Control ECU Assembly LH*2 5.656,5.427 6.271,5.625 0.615,0.198 10 false B4 5.635,5.615 6.896,6.104 1.26,0.49 10 false Headlight ECU Sub-assembly LH*3 2.292,6.344 2.906,6.542 0.615,0.198 10 false I113 2.292,6.542 4.854,6.771 2.563,0.229 10 false No. 3 Global CAN Junction Connector 0.167,6.948 5.75,7.51 5.583,0.563 10 false *1: w/ Power Tilt and Power Telescopic Steering Column System 0.177,7.25 5.26,7.594 5.083,0.344 10 false *2: w/ Reverse Shift-linked Mirror 0.167,7.552 2.25,7.792 2.083,0.24 10 false *3: w/ Headlight ECU 2.552,7.563 5.146,7.854 2.594,0.292 10 false *4: w/ Seat Position Memory System

C459277E01
2.813,6.667 4.604,7.083 1.792,0.417 10 false No. 11 Global CAN Junction Connector 0.094,4 1.656,4.406 1.563,0.406 10 false Air Conditioning Amplifier Assembly 0.802,1.073 1.302,1.281 0.5,0.208 10 false CANH 0.833,1.594 1.313,1.813 0.479,0.219 10 false CANL 0.823,3.052 1.302,3.271 0.479,0.219 10 false CANH 0.823,3.531 1.302,3.75 0.479,0.219 10 false CANL 0.667,6.177 1.146,6.396 0.479,0.219 10 false CANL 0.656,5.385 1.135,5.604 0.479,0.219 10 false CANH 0.094,2.031 2.438,2.438 2.344,0.406 10 false Headlight ECU Sub-assembly RH*1 0.167,6.49 1.802,7.167 1.635,0.677 10 false Main Body ECU (Multiplex Network Body ECU) 5.5,2.052 7.073,2.583 1.573,0.531 10 false Outer Mirror Control ECU Assembly RH*2 5.906,6.052 6.438,6.24 0.531,0.188 10 false CANN 5.906,5.469 6.458,5.677 0.552,0.208 10 false CANP 5.885,1.073 6.365,1.292 0.479,0.219 10 false CANP 5.875,1.625 6.354,1.844 0.479,0.219 10 false CANN 4,0.729 4.479,0.948 0.479,0.219 10 false 13 4.031,0.458 4.51,0.677 0.479,0.219 10 false 3 1.323,2.958 1.802,3.177 0.479,0.219 10 false 2 0.104,1.833 0.583,2.052 0.479,0.219 10 false B7 0.094,3.802 0.573,4.021 0.479,0.219 10 false I33 3.094,0.958 3.573,1.177 0.479,0.219 10 false 6 5.5,1.854 5.979,2.073 0.479,0.219 10 false M1 5.635,0.979 6.365,1.25 0.729,0.271 10 false 9 5.646,1.521 6.375,1.792 0.729,0.271 10 false 8 4.021,5.427 4.5,5.656 0.479,0.229 10 false 3 4.031,5.917 4.51,6.135 0.479,0.219 10 false 9 2.854,3.823 3.333,4.042 0.479,0.219 10 false I114 3.104,5.927 3.583,6.156 0.479,0.229 10 false 8 3.042,1.521 3.521,1.74 0.479,0.219 10 false 16 1.313,5.958 1.792,6.177 0.479,0.219 10 false 1 1.344,5.385 1.823,5.604 0.479,0.219 10 false 2 3.031,3.49 3.51,3.708 0.479,0.219 10 false 17 3.125,2.938 3.604,3.156 0.479,0.219 10 false 7 1.323,0.958 1.802,1.177 0.479,0.219 10 false 24 1.313,1.51 1.792,1.729 0.479,0.219 10 false 23 5.188,6.26 5.667,6.479 0.479,0.219 10 false T1 3.115,5.396 3.594,5.615 0.479,0.219 10 false 2 1.302,3.5 1.781,3.719 0.479,0.219 10 false 1 4.031,5.188 4.76,5.458 0.729,0.271 10 false 7 4.031,4.938 4.76,5.208 0.729,0.271 10 false 1 0.146,8.438 2.646,8.708 2.5,0.271 10 false *3: w/ Power Back Door System 0.177,8.031 3.271,8.333 3.094,0.302 10 false *2: w/ Reverse Shift-linked Mirror 4.01,1.531 4.49,1.75 0.479,0.219 10 false 14 0.177,7.635 2.021,7.99 1.844,0.354 10 false *1: w/ Headlight ECU 5.604,5.417 6.083,5.635 0.479,0.219 10 false 10 4.031,1 4.51,1.219 0.479,0.219 10 false 4 5.167,6.469 7.135,6.854 1.969,0.385 10 false Multiplex Network Door ECU*3 5.604,5.938 6.083,6.156 0.479,0.219 10 false 20 2.813,6.458 3.292,6.677 0.479,0.219 10 false Q62 0.167,6.302 0.646,6.521 0.479,0.219 10 false I3 4.052,2.948 4.531,3.167 0.479,0.219 10 false 10 4.052,3.5 4.531,3.719 0.479,0.219 10 false 20 2.844,4.021 4.542,4.5 1.698,0.479 10 false No. 4 Global CAN Junction Connector

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the battery.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

Some parts must be initialized and set when replacing or removing and installing parts.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

·

Before replacing the certification ECU (smart key ECU assembly), refer to Service Bulletin.



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE
NOTICE:

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.


HINT:

Operating the ignition switch, any other switches or door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.


a.

Disconnect the cable from the negative (-) battery terminal.


b.
C458715C06
1.51,0.073 1.927,0.323 0.417,0.25 2.917,1.719 2.76,1.719 2.76,1.719 2.25,0.771 true 2.531,1.906 2.375,1.906 2.375,1.906 2.156,0.781 true 0.115,0.073 0.427,0.271 0.313,0.198 10 false *a 1.635,0.115 2.094,0.313 0.458,0.198 10 false I42 2.958,1.635 3.427,1.854 0.469,0.219 10 false CA5H 2.625,1.833 3.188,2.083 0.563,0.25 10 false CA5L
*a Component with harness connected
(Central Gateway ECU [Network Gateway ECU])


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I42)Location & Routing

Click Connector(I42)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Network Gateway ECU

I42-7 (CA5H) - I42-8 (CA5L) Cable disconnected from negative (-) battery terminal Below 70 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK FOR SHORT IN CAN BUS WIRES

NG

104.CHECK FOR OPEN IN CAN BUS WIRE (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - NO. 4 GLOBAL CAN JUNCTION CONNECTOR)
2.CHECK FOR SHORT IN CAN BUS WIRES
a.
C458715C06
1.51,0.073 1.927,0.323 0.417,0.25 2.917,1.719 2.76,1.719 2.76,1.719 2.25,0.771 true 2.531,1.906 2.375,1.906 2.375,1.906 2.156,0.781 true 0.115,0.073 0.427,0.271 0.313,0.198 10 false *a 1.635,0.115 2.094,0.313 0.458,0.198 10 false I42 2.958,1.635 3.427,1.854 0.469,0.219 10 false CA5H 2.625,1.833 3.188,2.083 0.563,0.25 10 false CA5L
*a Component with harness connected
(Central Gateway ECU [Network Gateway ECU])


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I42)Location & Routing

Click Connector(I42)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Network Gateway ECU

I42-7 (CA5H) - I42-8 (CA5L) Cable disconnected from negative (-) battery terminal 54 Ω or higher



Result:
Proceed to
OK
NG



OK

3.CHECK FOR SHORT TO B+ IN CAN BUS WIRE

NG

71.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - NO. 4 GLOBAL CAN JUNCTION CONNECTOR)
3.CHECK FOR SHORT TO B+ IN CAN BUS WIRE
a.
C458715C06
1.51,0.073 1.927,0.323 0.417,0.25 2.917,1.719 2.76,1.719 2.76,1.719 2.25,0.771 true 2.531,1.906 2.375,1.906 2.375,1.906 2.156,0.781 true 0.115,0.073 0.427,0.271 0.313,0.198 10 false *a 1.635,0.115 2.094,0.313 0.458,0.198 10 false I42 2.958,1.635 3.427,1.854 0.469,0.219 10 false CA5H 2.625,1.833 3.188,2.083 0.563,0.25 10 false CA5L
*a Component with harness connected
(Central Gateway ECU [Network Gateway ECU])


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I42,I76)Location & Routing

Click Connector(I42)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Network Gateway ECU

Click Connector(I76)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Data Link Connector 3

I42-7 (CA5H) - I76-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
I42-8 (CA5L) - I76-16 (BAT)



Result:
Proceed to
OK
NG



OK

4.CHECK FOR SHORT TO GND IN CAN BUS WIRE

NG

38.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - NO. 4 GLOBAL CAN JUNCTION CONNECTOR)
4.CHECK FOR SHORT TO GND IN CAN BUS WIRE
a.
C458715C06
1.51,0.073 1.927,0.323 0.417,0.25 2.917,1.719 2.76,1.719 2.76,1.719 2.25,0.771 true 2.531,1.906 2.375,1.906 2.375,1.906 2.156,0.781 true 0.115,0.073 0.427,0.271 0.313,0.198 10 false *a 1.635,0.115 2.094,0.313 0.458,0.198 10 false I42 2.958,1.635 3.427,1.854 0.469,0.219 10 false CA5H 2.625,1.833 3.188,2.083 0.563,0.25 10 false CA5L
*a Component with harness connected
(Central Gateway ECU [Network Gateway ECU])


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I42,I76)Location & Routing

Click Connector(I42)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Network Gateway ECU

Click Connector(I76)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Data Link Connector 3

I42-7 (CA5H) - I76-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
I42-8 (CA5L) - I76-4 (CG)



Result:
Proceed to
OK
NG



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

5.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - NO. 4 GLOBAL CAN JUNCTION CONNECTOR)
5.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - NO. 4 GLOBAL CAN JUNCTION CONNECTOR)
a.

Disconnect the I113 No. 3 global CAN junction connector.



Result:
Proceed to
OK
NG



OK

6.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU])

NG

16.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - NO. 3 GLOBAL CAN JUNCTION CONNECTOR)
6.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU])

OK

7.CHECK VEHICLE TYPE

NG

32.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU])
7.CHECK VEHICLE TYPE
a.

Check for vehicle type.


Result:
Result Proceed to
w/ Reverse Shift-linked Mirror A
w/o Reverse Shift-linked Mirror B



A

8.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - OUTER MIRROR CONTROL ECU ASSEMBLY LH)

B

9.CHECK VEHICLE TYPE
8.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - OUTER MIRROR CONTROL ECU ASSEMBLY LH)

OK

9.CHECK VEHICLE TYPE

NG

33.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - OUTER MIRROR CONTROL ECU ASSEMBLY LH)
9.CHECK VEHICLE TYPE
a.

Check for vehicle type.


Result:
Result Proceed to
w/ Power Tilt and Power Telescopic Steering Column System A
w/o Power Tilt and Power Telescopic Steering Column System B



A

10.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - MULTIPLEX TILT AND TELESCOPIC ECU)

B

11.CHECK VEHICLE TYPE
10.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - MULTIPLEX TILT AND TELESCOPIC ECU)

OK

11.CHECK VEHICLE TYPE

NG

34.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - MULTIPLEX TILT AND TELESCOPIC ECU)
11.CHECK VEHICLE TYPE
a.

Check for vehicle type.


Result:
Result Proceed to
w/ Headlight ECU A
w/o Headlight ECU B



A

12.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - HEADLIGHT ECU SUB-ASSEMBLY LH)

B

13.CHECK VEHICLE TYPE
12.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - HEADLIGHT ECU SUB-ASSEMBLY LH)

OK

13.CHECK VEHICLE TYPE

NG

35.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - HEADLIGHT ECU SUB-ASSEMBLY LH)
13.CHECK VEHICLE TYPE
a.

Check for vehicle type.


Result:
Result Proceed to
w/ Seat Position Memory System A
w/o Seat Position Memory System B



A

14.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - POSITION CONTROL ECU ASSEMBLY)

B

15.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - CERTIFICATION ECU [SMART KEY ECU ASSEMBLY])
14.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - POSITION CONTROL ECU ASSEMBLY)

OK

15.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - CERTIFICATION ECU [SMART KEY ECU ASSEMBLY])

NG

36.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - POSITION CONTROL ECU ASSEMBLY)
15.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - CERTIFICATION ECU [SMART KEY ECU ASSEMBLY])

OK

REPLACE NO. 3 GLOBAL CAN JUNCTION CONNECTOR

NG

37.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - CERTIFICATION ECU [SMART KEY ECU ASSEMBLY])
16.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - NO. 3 GLOBAL CAN JUNCTION CONNECTOR)
a.

Disconnect the I114 No. 4 global CAN junction connector.



Result:
Proceed to
OK
NG



OK

17.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - NO. 11 GLOBAL CAN JUNCTION CONNECTOR)

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - NO. 3 GLOBAL CAN JUNCTION CONNECTOR)

17.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - NO. 11 GLOBAL CAN JUNCTION CONNECTOR)

OK

18.CHECK VEHICLE TYPE

NG

23.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 11 GLOBAL CAN JUNCTION CONNECTOR - NO. 4 GLOBAL CAN JUNCTION CONNECTOR)
18.CHECK VEHICLE TYPE
a.

Check for vehicle type.


Result:
Result Proceed to
w/ Headlight ECU A
w/o Headlight ECU B



A

19.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - HEADLIGHT ECU SUB-ASSEMBLY RH)

B

20.CHECK VEHICLE TYPE
19.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - HEADLIGHT ECU SUB-ASSEMBLY RH)

OK

20.CHECK VEHICLE TYPE

NG

29.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - HEADLIGHT ECU SUB-ASSEMBLY RH)
20.CHECK VEHICLE TYPE
a.

Check for vehicle type.


Result:
Result Proceed to
w/ Reverse Shift-linked Mirror A
w/o Reverse Shift-linked Mirror B



A

21.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - OUTER MIRROR CONTROL ECU ASSEMBLY RH)

B

22.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - AIR CONDITIONING AMPLIFIER ASSEMBLY)
21.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - OUTER MIRROR CONTROL ECU ASSEMBLY RH)

OK

22.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - AIR CONDITIONING AMPLIFIER ASSEMBLY)

NG

30.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - OUTER MIRROR CONTROL ECU ASSEMBLY RH)
22.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - AIR CONDITIONING AMPLIFIER ASSEMBLY)

OK

REPLACE NO. 4 GLOBAL CAN JUNCTION CONNECTOR

NG

31.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - AIR CONDITIONING AMPLIFIER ASSEMBLY)
23.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 11 GLOBAL CAN JUNCTION CONNECTOR - NO. 4 GLOBAL CAN JUNCTION CONNECTOR)
a.

Disconnect the Q62 No. 11 global CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(Q62,I76)Location & Routing

Click Connector(Q62)Body>Air Conditioning Wiring Harness Assembly / Floor Wire / Step Rear Floor Wire RH / Theft Warning Sensor Cord Sub-Assembly>No. 11 Global CAN Junction Connector

Click Connector(I76)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Data Link Connector 3

Q62-1 (CANH) - I76-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
Q62-7 (CANL) - I76-4 (CG)



Result:
Proceed to
OK
NG



OK

24.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 11 GLOBAL CAN JUNCTION CONNECTOR - MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU])

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 11 GLOBAL CAN JUNCTION CONNECTOR - NO. 4 GLOBAL CAN JUNCTION CONNECTOR)

24.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 11 GLOBAL CAN JUNCTION CONNECTOR - MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU])
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(Q62,I76)Location & Routing

Click Connector(Q62)Body>Air Conditioning Wiring Harness Assembly / Floor Wire / Step Rear Floor Wire RH / Theft Warning Sensor Cord Sub-Assembly>No. 11 Global CAN Junction Connector

Click Connector(I76)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Data Link Connector 3

Q62-2 (CANH) - I76-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
Q62-8 (CANL) - I76-4 (CG)



Result:
Proceed to
OK
NG



OK

25.CHECK VEHICLE TYPE

NG

27.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 11 GLOBAL CAN JUNCTION CONNECTOR - MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU])
25.CHECK VEHICLE TYPE
a.

Check for vehicle type.


Result:
Result Proceed to
w/ Power Back Door System A
w/o Power Back Door System B



A

26.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 11 GLOBAL CAN JUNCTION CONNECTOR - MULTIPLEX NETWORK DOOR ECU)

B

REPLACE NO. 11 GLOBAL CAN JUNCTION CONNECTOR

26.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 11 GLOBAL CAN JUNCTION CONNECTOR - MULTIPLEX NETWORK DOOR ECU)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(Q62,I76)Location & Routing

Click Connector(Q62)Body>Air Conditioning Wiring Harness Assembly / Floor Wire / Step Rear Floor Wire RH / Theft Warning Sensor Cord Sub-Assembly>No. 11 Global CAN Junction Connector

Click Connector(I76)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Data Link Connector 3

Q62-3 (CANH) - I76-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
Q62-9 (CANL) - I76-4 (CG)



Result:
Proceed to
OK
NG



OK

REPLACE NO. 11 GLOBAL CAN JUNCTION CONNECTOR

NG

28.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 11 GLOBAL CAN JUNCTION CONNECTOR - MULTIPLEX NETWORK DOOR ECU)
27.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 11 GLOBAL CAN JUNCTION CONNECTOR - MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU])
a.

Disconnect the I3 main body ECU (multiplex network body ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(Q62,I76)Location & Routing

Click Connector(Q62)Body>Air Conditioning Wiring Harness Assembly / Floor Wire / Step Rear Floor Wire RH / Theft Warning Sensor Cord Sub-Assembly>No. 11 Global CAN Junction Connector

Click Connector(I76)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Data Link Connector 3

Q62-2 (CANH) - I76-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
Q62-8 (CANL) - I76-4 (CG)



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 11 GLOBAL CAN JUNCTION CONNECTOR - MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU])

28.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 11 GLOBAL CAN JUNCTION CONNECTOR - MULTIPLEX NETWORK DOOR ECU)
a.

Disconnect the T1 multiplex network door ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(Q62,I76)Location & Routing

Click Connector(Q62)Body>Air Conditioning Wiring Harness Assembly / Floor Wire / Step Rear Floor Wire RH / Theft Warning Sensor Cord Sub-Assembly>No. 11 Global CAN Junction Connector

Click Connector(I76)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Data Link Connector 3

Q62-3 (CANH) - I76-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
Q62-9 (CANL) - I76-4 (CG)



Result:
Proceed to
OK
NG



OK

REPLACE MULTIPLEX NETWORK DOOR ECU

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 11 GLOBAL CAN JUNCTION CONNECTOR - MULTIPLEX NETWORK DOOR ECU)

29.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - HEADLIGHT ECU SUB-ASSEMBLY RH)
a.

Disconnect the B7 headlight ECU sub-assembly RH connector.



Result:
Proceed to
OK
NG



OK

REPLACE HEADLIGHT ECU SUB-ASSEMBLY RH

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - HEADLIGHT ECU SUB-ASSEMBLY RH)

30.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - OUTER MIRROR CONTROL ECU ASSEMBLY RH)
a.

Disconnect the M1 outer mirror control ECU assembly RH connector.



Result:
Proceed to
OK
NG



OK

REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY RH

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - OUTER MIRROR CONTROL ECU ASSEMBLY RH)

31.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - AIR CONDITIONING AMPLIFIER ASSEMBLY)
a.

Disconnect the I33 air conditioning amplifier assembly connector.



Result:
Proceed to
OK
NG



OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - AIR CONDITIONING AMPLIFIER ASSEMBLY)

32.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU])
a.

Disconnect the I42 central gateway ECU (network gateway ECU) connector.



Result:
Proceed to
OK
NG



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU])

33.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - OUTER MIRROR CONTROL ECU ASSEMBLY LH)
a.

Disconnect the N1 outer mirror control ECU assembly LH connector.



Result:
Proceed to
OK
NG



OK

REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY LH

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - OUTER MIRROR CONTROL ECU ASSEMBLY LH)

34.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - MULTIPLEX TILT AND TELESCOPIC ECU)
a.

Disconnect the I43 multiplex tilt and telescopic ECU connector.



Result:
Proceed to
OK
NG



OK

REPLACE MULTIPLEX TILT AND TELESCOPIC ECU

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - MULTIPLEX TILT AND TELESCOPIC ECU)

35.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - HEADLIGHT ECU SUB-ASSEMBLY LH)
a.

Disconnect the B4 headlight ECU sub-assembly LH connector.



Result:
Proceed to
OK
NG



OK

REPLACE HEADLIGHT ECU SUB-ASSEMBLY LH

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - HEADLIGHT ECU SUB-ASSEMBLY LH)

36.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - POSITION CONTROL ECU ASSEMBLY)
a.

Disconnect the i19 position control ECU assembly connector.



Result:
Proceed to
OK
NG



OK

REPLACE POSITION CONTROL ECU ASSEMBLY

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - POSITION CONTROL ECU ASSEMBLY)

37.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - CERTIFICATION ECU [SMART KEY ECU ASSEMBLY])
a.

Disconnect the I39 certification ECU (smart key ECU assembly) connector.



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - CERTIFICATION ECU [SMART KEY ECU ASSEMBLY])

38.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - NO. 4 GLOBAL CAN JUNCTION CONNECTOR)
a.

Disconnect the I113 No. 3 global CAN junction connector.



Result:
Proceed to
OK
NG



OK

39.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU])

NG

49.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - NO. 3 GLOBAL CAN JUNCTION CONNECTOR)
39.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU])

OK

40.CHECK VEHICLE TYPE

NG

65.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU])
40.CHECK VEHICLE TYPE
a.

Check for vehicle type.


Result:
Result Proceed to
w/ Reverse Shift-linked Mirror A
w/o Reverse Shift-linked Mirror B



A

41.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - OUTER MIRROR CONTROL ECU ASSEMBLY LH)

B

42.CHECK VEHICLE TYPE
41.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - OUTER MIRROR CONTROL ECU ASSEMBLY LH)

OK

42.CHECK VEHICLE TYPE

NG

66.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - OUTER MIRROR CONTROL ECU ASSEMBLY LH)
42.CHECK VEHICLE TYPE
a.

Check for vehicle type.


Result:
Result Proceed to
w/ Power Tilt and Power Telescopic Steering Column System A
w/o Power Tilt and Power Telescopic Steering Column System B



A

43.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - MULTIPLEX TILT AND TELESCOPIC ECU)

B

44.CHECK VEHICLE TYPE
43.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - MULTIPLEX TILT AND TELESCOPIC ECU)

OK

44.CHECK VEHICLE TYPE

NG

67.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - MULTIPLEX TILT AND TELESCOPIC ECU)
44.CHECK VEHICLE TYPE
a.

Check for vehicle type.


Result:
Result Proceed to
w/ Headlight ECU A
w/o Headlight ECU B



A

45.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - HEADLIGHT ECU SUB-ASSEMBLY LH)

B

46.CHECK VEHICLE TYPE
45.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - HEADLIGHT ECU SUB-ASSEMBLY LH)

OK

46.CHECK VEHICLE TYPE

NG

68.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - HEADLIGHT ECU SUB-ASSEMBLY LH)
46.CHECK VEHICLE TYPE
a.

Check for vehicle type.


Result:
Result Proceed to
w/ Seat Position Memory System A
w/o Seat Position Memory System B



A

47.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - POSITION CONTROL ECU ASSEMBLY)

B

48.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - CERTIFICATION ECU [SMART KEY ECU ASSEMBLY])
47.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - POSITION CONTROL ECU ASSEMBLY)

OK

48.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - CERTIFICATION ECU [SMART KEY ECU ASSEMBLY])

NG

69.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - POSITION CONTROL ECU ASSEMBLY)
48.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - CERTIFICATION ECU [SMART KEY ECU ASSEMBLY])

OK

REPLACE NO. 3 GLOBAL CAN JUNCTION CONNECTOR

NG

70.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - CERTIFICATION ECU [SMART KEY ECU ASSEMBLY])
49.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - NO. 3 GLOBAL CAN JUNCTION CONNECTOR)
a.

Disconnect the I114 No. 4 global CAN junction connector.



Result:
Proceed to
OK
NG



OK

50.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - NO. 11 GLOBAL CAN JUNCTION CONNECTOR)

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - NO. 3 GLOBAL CAN JUNCTION CONNECTOR)

50.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - NO. 11 GLOBAL CAN JUNCTION CONNECTOR)

OK

51.CHECK VEHICLE TYPE

NG

56.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 11 GLOBAL CAN JUNCTION CONNECTOR - NO. 4 GLOBAL CAN JUNCTION CONNECTOR)
51.CHECK VEHICLE TYPE
a.

Check for vehicle type.


Result:
Result Proceed to
w/ Headlight ECU A
w/o Headlight ECU B



A

52.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - HEADLIGHT ECU SUB-ASSEMBLY RH)

B

53.CHECK VEHICLE TYPE
52.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - HEADLIGHT ECU SUB-ASSEMBLY RH)

OK

53.CHECK VEHICLE TYPE

NG

62.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - HEADLIGHT ECU SUB-ASSEMBLY RH)
53.CHECK VEHICLE TYPE
a.

Check for vehicle type.


Result:
Result Proceed to
w/ Reverse Shift-linked Mirror A
w/o Reverse Shift-linked Mirror B



A

54.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - OUTER MIRROR CONTROL ECU ASSEMBLY RH)

B

55.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - AIR CONDITIONING AMPLIFIER ASSEMBLY)
54.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - OUTER MIRROR CONTROL ECU ASSEMBLY RH)

OK

55.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - AIR CONDITIONING AMPLIFIER ASSEMBLY)

NG

63.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - OUTER MIRROR CONTROL ECU ASSEMBLY RH)
55.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - AIR CONDITIONING AMPLIFIER ASSEMBLY)

OK

REPLACE NO. 4 GLOBAL CAN JUNCTION CONNECTOR

NG

64.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - AIR CONDITIONING AMPLIFIER ASSEMBLY)
56.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 11 GLOBAL CAN JUNCTION CONNECTOR - NO. 4 GLOBAL CAN JUNCTION CONNECTOR)
a.

Disconnect the Q62 No. 11 global CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(Q62,I76)Location & Routing

Click Connector(Q62)Body>Air Conditioning Wiring Harness Assembly / Floor Wire / Step Rear Floor Wire RH / Theft Warning Sensor Cord Sub-Assembly>No. 11 Global CAN Junction Connector

Click Connector(I76)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Data Link Connector 3

Q62-1 (CANH) - I76-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
Q62-7 (CANL) - I76-16 (BAT)



Result:
Proceed to
OK
NG



OK

57.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 11 GLOBAL CAN JUNCTION CONNECTOR - MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU])

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 11 GLOBAL CAN JUNCTION CONNECTOR - NO. 4 GLOBAL CAN JUNCTION CONNECTOR)

57.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 11 GLOBAL CAN JUNCTION CONNECTOR - MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU])
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(Q62,I76)Location & Routing

Click Connector(Q62)Body>Air Conditioning Wiring Harness Assembly / Floor Wire / Step Rear Floor Wire RH / Theft Warning Sensor Cord Sub-Assembly>No. 11 Global CAN Junction Connector

Click Connector(I76)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Data Link Connector 3

Q62-2 (CANH) - I76-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
Q62-8 (CANL) - I76-16 (BAT)



Result:
Proceed to
OK
NG



OK

58.CHECK VEHICLE TYPE

NG

60.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 11 GLOBAL CAN JUNCTION CONNECTOR - MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU])
58.CHECK VEHICLE TYPE
a.

Check for vehicle type.


Result:
Result Proceed to
w/ Power Back Door System A
w/o Power Back Door System B



A

59.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 11 GLOBAL CAN JUNCTION CONNECTOR - MULTIPLEX NETWORK DOOR ECU)

B

REPLACE NO. 11 GLOBAL CAN JUNCTION CONNECTOR

59.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 11 GLOBAL CAN JUNCTION CONNECTOR - MULTIPLEX NETWORK DOOR ECU)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(Q62,I76)Location & Routing

Click Connector(Q62)Body>Air Conditioning Wiring Harness Assembly / Floor Wire / Step Rear Floor Wire RH / Theft Warning Sensor Cord Sub-Assembly>No. 11 Global CAN Junction Connector

Click Connector(I76)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Data Link Connector 3

Q62-3 (CANH) - I76-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
Q62-9 (CANL) - I76-16 (BAT)



Result:
Proceed to
OK
NG



OK

REPLACE NO. 11 GLOBAL CAN JUNCTION CONNECTOR

NG

61.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 11 GLOBAL CAN JUNCTION CONNECTOR - MULTIPLEX NETWORK DOOR ECU)
60.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 11 GLOBAL CAN JUNCTION CONNECTOR - MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU])
a.

Disconnect the I3 main body ECU (multiplex network body ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(Q62,I76)Location & Routing

Click Connector(Q62)Body>Air Conditioning Wiring Harness Assembly / Floor Wire / Step Rear Floor Wire RH / Theft Warning Sensor Cord Sub-Assembly>No. 11 Global CAN Junction Connector

Click Connector(I76)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Data Link Connector 3

Q62-2 (CANH) - I76-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
Q62-8 (CANL) - I76-16 (BAT)



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 11 GLOBAL CAN JUNCTION CONNECTOR - MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU])

61.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 11 GLOBAL CAN JUNCTION CONNECTOR - MULTIPLEX NETWORK DOOR ECU)
a.

Disconnect the T1 multiplex network door ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(Q62,I76)Location & Routing

Click Connector(Q62)Body>Air Conditioning Wiring Harness Assembly / Floor Wire / Step Rear Floor Wire RH / Theft Warning Sensor Cord Sub-Assembly>No. 11 Global CAN Junction Connector

Click Connector(I76)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Data Link Connector 3

Q62-3 (CANH) - I76-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
Q62-9 (CANL) - I76-16 (BAT)



Result:
Proceed to
OK
NG



OK

REPLACE MULTIPLEX NETWORK DOOR ECU

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 11 GLOBAL CAN JUNCTION CONNECTOR - MULTIPLEX NETWORK DOOR ECU)

62.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - HEADLIGHT ECU SUB-ASSEMBLY RH)
a.

Disconnect the B7 headlight ECU sub-assembly RH connector.



Result:
Proceed to
OK
NG



OK

REPLACE HEADLIGHT ECU SUB-ASSEMBLY RH

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - HEADLIGHT ECU SUB-ASSEMBLY RH)

63.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - OUTER MIRROR CONTROL ECU ASSEMBLY RH)
a.

Disconnect the M1 outer mirror control ECU assembly RH connector.



Result:
Proceed to
OK
NG



OK

REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY RH

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - OUTER MIRROR CONTROL ECU ASSEMBLY RH)

64.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - AIR CONDITIONING AMPLIFIER ASSEMBLY)
a.

Disconnect the I33 air conditioning amplifier assembly connector.



Result:
Proceed to
OK
NG



OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - AIR CONDITIONING AMPLIFIER ASSEMBLY)

65.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU])
a.

Disconnect the I42 central gateway ECU (network gateway ECU) connector.



Result:
Proceed to
OK
NG



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU])

66.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - OUTER MIRROR CONTROL ECU ASSEMBLY LH)
a.

Disconnect the N1 outer mirror control ECU assembly LH connector.



Result:
Proceed to
OK
NG



OK

REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY LH

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - OUTER MIRROR CONTROL ECU ASSEMBLY LH)

67.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - MULTIPLEX TILT AND TELESCOPIC ECU)
a.

Disconnect the I43 multiplex tilt and telescopic ECU connector.



Result:
Proceed to
OK
NG



OK

REPLACE MULTIPLEX TILT AND TELESCOPIC ECU

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - MULTIPLEX TILT AND TELESCOPIC ECU)

68.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - HEADLIGHT ECU SUB-ASSEMBLY LH)
a.

Disconnect the B4 headlight ECU sub-assembly LH connector.



Result:
Proceed to
OK
NG



OK

REPLACE HEADLIGHT ECU SUB-ASSEMBLY LH

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - HEADLIGHT ECU SUB-ASSEMBLY LH)

69.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - POSITION CONTROL ECU ASSEMBLY)
a.

Disconnect the i19 position control ECU assembly connector.



Result:
Proceed to
OK
NG



OK

REPLACE POSITION CONTROL ECU ASSEMBLY

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - POSITION CONTROL ECU ASSEMBLY)

70.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - CERTIFICATION ECU [SMART KEY ECU ASSEMBLY])
a.

Disconnect the I39 certification ECU (smart key ECU assembly) connector.



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - CERTIFICATION ECU [SMART KEY ECU ASSEMBLY])

71.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - NO. 4 GLOBAL CAN JUNCTION CONNECTOR)
a.

Disconnect the I113 No. 3 global CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I113)Location & Routing

Click Connector(I113)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>No. 3 Global CAN Junction Connector

I113-2 (CANH) - I113-12 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG



OK

72.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU])

NG

82.CHECK FOR SHORT IN CAN BUS WIRES (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - NO. 3 GLOBAL CAN JUNCTION CONNECTOR)
72.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU])
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I113)Location & Routing

Click Connector(I113)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>No. 3 Global CAN Junction Connector

I113-1 (CANH) - I113-11 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

73.CHECK VEHICLE TYPE

NG

98.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU])
73.CHECK VEHICLE TYPE
a.

Check for vehicle type.


Result:
Result Proceed to
w/ Reverse Shift-linked Mirror A
w/o Reverse Shift-linked Mirror B



A

74.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - OUTER MIRROR CONTROL ECU ASSEMBLY LH)

B

75.CHECK VEHICLE TYPE
74.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - OUTER MIRROR CONTROL ECU ASSEMBLY LH)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I113)Location & Routing

Click Connector(I113)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>No. 3 Global CAN Junction Connector

I113-6 (CANH) - I113-16 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG



OK

75.CHECK VEHICLE TYPE

NG

99.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - OUTER MIRROR CONTROL ECU ASSEMBLY LH)
75.CHECK VEHICLE TYPE
a.

Check for vehicle type.


Result:
Result Proceed to
w/ Power Tilt and Power Telescopic Steering Column System A
w/o Power Tilt and Power Telescopic Steering Column System B



A

76.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - MULTIPLEX TILT AND TELESCOPIC ECU)

B

77.CHECK VEHICLE TYPE
76.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - MULTIPLEX TILT AND TELESCOPIC ECU)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I113)Location & Routing

Click Connector(I113)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>No. 3 Global CAN Junction Connector

I113-4 (CANH) - I113-14 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG



OK

77.CHECK VEHICLE TYPE

NG

100.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - MULTIPLEX TILT AND TELESCOPIC ECU)
77.CHECK VEHICLE TYPE
a.

Check for vehicle type.


Result:
Result Proceed to
w/ Headlight ECU A
w/o Headlight ECU B



A

78.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - HEADLIGHT ECU SUB-ASSEMBLY LH)

B

79.CHECK VEHICLE TYPE
78.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - HEADLIGHT ECU SUB-ASSEMBLY LH)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I113)Location & Routing

Click Connector(I113)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>No. 3 Global CAN Junction Connector

I113-9 (CANH) - I113-19 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG



OK

79.CHECK VEHICLE TYPE

NG

101.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - HEADLIGHT ECU SUB-ASSEMBLY LH)
79.CHECK VEHICLE TYPE
a.

Check for vehicle type.


Result:
Result Proceed to
w/ Seat Position Memory System A
w/o Seat Position Memory System B



A

80.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - POSITION CONTROL ECU ASSEMBLY)

B

81.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - CERTIFICATION ECU [SMART KEY ECU ASSEMBLY])
80.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - POSITION CONTROL ECU ASSEMBLY)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I113)Location & Routing

Click Connector(I113)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>No. 3 Global CAN Junction Connector

I113-8 (CANH) - I113-18 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG



OK

81.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - CERTIFICATION ECU [SMART KEY ECU ASSEMBLY])

NG

102.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - POSITION CONTROL ECU ASSEMBLY)
81.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - CERTIFICATION ECU [SMART KEY ECU ASSEMBLY])
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I113)Location & Routing

Click Connector(I113)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>No. 3 Global CAN Junction Connector

I113-3 (CANH) - I113-13 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG



OK

REPLACE NO. 3 GLOBAL CAN JUNCTION CONNECTOR

NG

103.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - CERTIFICATION ECU [SMART KEY ECU ASSEMBLY])
82.CHECK FOR SHORT IN CAN BUS WIRES (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - NO. 3 GLOBAL CAN JUNCTION CONNECTOR)
a.

Disconnect the I114 No. 4 global CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I114)Location & Routing

Click Connector(I114)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>No. 4 Global CAN Junction Connector

I114-3 (CANH) - I114-13 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG



OK

83.CHECK FOR SHORT IN CAN BUS WIRES (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - NO. 11 GLOBAL CAN JUNCTION CONNECTOR)

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - NO. 3 GLOBAL CAN JUNCTION CONNECTOR)

83.CHECK FOR SHORT IN CAN BUS WIRES (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - NO. 11 GLOBAL CAN JUNCTION CONNECTOR)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I114)Location & Routing

Click Connector(I114)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>No. 4 Global CAN Junction Connector

I114-10 (CANH) - I114-20 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

84.CHECK VEHICLE TYPE

NG

89.CHECK FOR SHORT IN CAN BUS WIRES (NO. 11 GLOBAL CAN JUNCTION CONNECTOR - NO. 4 GLOBAL CAN JUNCTION CONNECTOR)
84.CHECK VEHICLE TYPE
a.

Check for vehicle type.


Result:
Result Proceed to
w/ Headlight ECU A
w/o Headlight ECU B



A

85.CHECK FOR SHORT IN CAN BUS WIRES (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - HEADLIGHT ECU SUB-ASSEMBLY RH)

B

86.CHECK VEHICLE TYPE
85.CHECK FOR SHORT IN CAN BUS WIRES (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - HEADLIGHT ECU SUB-ASSEMBLY RH)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I114)Location & Routing

Click Connector(I114)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>No. 4 Global CAN Junction Connector

I114-6 (CANH) - I114-16 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG



OK

86.CHECK VEHICLE TYPE

NG

95.CHECK FOR SHORT IN CAN BUS WIRES (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - HEADLIGHT ECU SUB-ASSEMBLY RH)
86.CHECK VEHICLE TYPE
a.

Check for vehicle type.


Result:
Result Proceed to
w/ Reverse Shift-linked Mirror A
w/o Reverse Shift-linked Mirror B



A

87.CHECK FOR SHORT IN CAN BUS WIRES (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - OUTER MIRROR CONTROL ECU ASSEMBLY RH)

B

88.CHECK FOR SHORT IN CAN BUS WIRES (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - AIR CONDITIONING AMPLIFIER ASSEMBLY)
87.CHECK FOR SHORT IN CAN BUS WIRES (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - OUTER MIRROR CONTROL ECU ASSEMBLY RH)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I114)Location & Routing

Click Connector(I114)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>No. 4 Global CAN Junction Connector

I114-4 (CANH) - I114-14 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG



OK

88.CHECK FOR SHORT IN CAN BUS WIRES (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - AIR CONDITIONING AMPLIFIER ASSEMBLY)

NG

96.CHECK FOR SHORT IN CAN BUS WIRES (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - OUTER MIRROR CONTROL ECU ASSEMBLY RH)
88.CHECK FOR SHORT IN CAN BUS WIRES (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - AIR CONDITIONING AMPLIFIER ASSEMBLY)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I114)Location & Routing

Click Connector(I114)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>No. 4 Global CAN Junction Connector

I114-7 (CANH) - I114-17 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG



OK

REPLACE NO. 4 GLOBAL CAN JUNCTION CONNECTOR

NG

97.CHECK FOR SHORT IN CAN BUS WIRES (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - AIR CONDITIONING AMPLIFIER ASSEMBLY)
89.CHECK FOR SHORT IN CAN BUS WIRES (NO. 11 GLOBAL CAN JUNCTION CONNECTOR - NO. 4 GLOBAL CAN JUNCTION CONNECTOR)
a.

Disconnect the Q62 No. 11 global CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(Q62)Location & Routing

Click Connector(Q62)Body>Air Conditioning Wiring Harness Assembly / Floor Wire / Step Rear Floor Wire RH / Theft Warning Sensor Cord Sub-Assembly>No. 11 Global CAN Junction Connector

Q62-1 (CANH) - Q62-7 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG



OK

90.CHECK FOR SHORT IN CAN BUS WIRES (NO. 11 GLOBAL CAN JUNCTION CONNECTOR - MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU])

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 11 GLOBAL CAN JUNCTION CONNECTOR - NO. 4 GLOBAL CAN JUNCTION CONNECTOR)

90.CHECK FOR SHORT IN CAN BUS WIRES (NO. 11 GLOBAL CAN JUNCTION CONNECTOR - MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU])
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(Q62)Location & Routing

Click Connector(Q62)Body>Air Conditioning Wiring Harness Assembly / Floor Wire / Step Rear Floor Wire RH / Theft Warning Sensor Cord Sub-Assembly>No. 11 Global CAN Junction Connector

Q62-2 (CANH) - Q62-8 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

91.CHECK VEHICLE TYPE

NG

93.CHECK FOR SHORT IN CAN BUS WIRES (NO. 11 GLOBAL CAN JUNCTION CONNECTOR - MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU])
91.CHECK VEHICLE TYPE
a.

Check for vehicle type.


Result:
Result Proceed to
w/ Power Back Door System A
w/o Power Back Door System B



A

92.CHECK FOR SHORT IN CAN BUS WIRES (NO. 11 GLOBAL CAN JUNCTION CONNECTOR - MULTIPLEX NETWORK DOOR ECU)

B

REPLACE NO. 11 GLOBAL CAN JUNCTION CONNECTOR

92.CHECK FOR SHORT IN CAN BUS WIRES (NO. 11 GLOBAL CAN JUNCTION CONNECTOR - MULTIPLEX NETWORK DOOR ECU)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(Q62)Location & Routing

Click Connector(Q62)Body>Air Conditioning Wiring Harness Assembly / Floor Wire / Step Rear Floor Wire RH / Theft Warning Sensor Cord Sub-Assembly>No. 11 Global CAN Junction Connector

Q62-3 (CANH) - Q62-9 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG



OK

REPLACE NO. 11 GLOBAL CAN JUNCTION CONNECTOR

NG

94.CHECK FOR SHORT IN CAN BUS WIRES (NO. 11 GLOBAL CAN JUNCTION CONNECTOR - MULTIPLEX NETWORK DOOR ECU)
93.CHECK FOR SHORT IN CAN BUS WIRES (NO. 11 GLOBAL CAN JUNCTION CONNECTOR - MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU])
a.

Disconnect the I3 main body ECU (multiplex network body ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(Q62)Location & Routing

Click Connector(Q62)Body>Air Conditioning Wiring Harness Assembly / Floor Wire / Step Rear Floor Wire RH / Theft Warning Sensor Cord Sub-Assembly>No. 11 Global CAN Junction Connector

Q62-2 (CANH) - Q62-8 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 11 GLOBAL CAN JUNCTION CONNECTOR - MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU])

94.CHECK FOR SHORT IN CAN BUS WIRES (NO. 11 GLOBAL CAN JUNCTION CONNECTOR - MULTIPLEX NETWORK DOOR ECU)
a.

Disconnect the T1 multiplex network door ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(Q62)Location & Routing

Click Connector(Q62)Body>Air Conditioning Wiring Harness Assembly / Floor Wire / Step Rear Floor Wire RH / Theft Warning Sensor Cord Sub-Assembly>No. 11 Global CAN Junction Connector

Q62-3 (CANH) - Q62-9 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG



OK

REPLACE MULTIPLEX NETWORK DOOR ECU

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 11 GLOBAL CAN JUNCTION CONNECTOR - MULTIPLEX NETWORK DOOR ECU)

95.CHECK FOR SHORT IN CAN BUS WIRES (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - HEADLIGHT ECU SUB-ASSEMBLY RH)
a.

Disconnect the B7 headlight ECU sub-assembly RH connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I114)Location & Routing

Click Connector(I114)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>No. 4 Global CAN Junction Connector

I114-6 (CANH) - I114-16 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG



OK

REPLACE HEADLIGHT ECU SUB-ASSEMBLY RH

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - HEADLIGHT ECU SUB-ASSEMBLY RH)

96.CHECK FOR SHORT IN CAN BUS WIRES (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - OUTER MIRROR CONTROL ECU ASSEMBLY RH)
a.

Disconnect the M1 outer mirror control ECU assembly RH connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I114)Location & Routing

Click Connector(I114)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>No. 4 Global CAN Junction Connector

I114-4 (CANH) - I114-14 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG



OK

REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY RH

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - OUTER MIRROR CONTROL ECU ASSEMBLY RH)

97.CHECK FOR SHORT IN CAN BUS WIRES (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - AIR CONDITIONING AMPLIFIER ASSEMBLY)
a.

Disconnect the I33 air conditioning amplifier assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I114)Location & Routing

Click Connector(I114)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>No. 4 Global CAN Junction Connector

I114-7 (CANH) - I114-17 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG



OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - AIR CONDITIONING AMPLIFIER ASSEMBLY)

98.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU])
a.

Disconnect the I42 central gateway ECU (network gateway ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I113)Location & Routing

Click Connector(I113)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>No. 3 Global CAN Junction Connector

I113-1 (CANH) - I113-11 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU])

99.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - OUTER MIRROR CONTROL ECU ASSEMBLY LH)
a.

Disconnect the N1 outer mirror control ECU assembly LH connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I113)Location & Routing

Click Connector(I113)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>No. 3 Global CAN Junction Connector

I113-6 (CANH) - I113-16 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG



OK

REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY LH

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - OUTER MIRROR CONTROL ECU ASSEMBLY LH)

100.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - MULTIPLEX TILT AND TELESCOPIC ECU)
a.

Disconnect the I43 multiplex tilt and telescopic ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I113)Location & Routing

Click Connector(I113)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>No. 3 Global CAN Junction Connector

I113-4 (CANH) - I113-14 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG



OK

REPLACE MULTIPLEX TILT AND TELESCOPIC ECU

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - MULTIPLEX TILT AND TELESCOPIC ECU)

101.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - HEADLIGHT ECU SUB-ASSEMBLY LH)
a.

Disconnect the B4 headlight ECU sub-assembly LH connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I113)Location & Routing

Click Connector(I113)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>No. 3 Global CAN Junction Connector

I113-9 (CANH) - I113-19 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG



OK

REPLACE HEADLIGHT ECU SUB-ASSEMBLY LH

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - HEADLIGHT ECU SUB-ASSEMBLY LH)

102.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - POSITION CONTROL ECU ASSEMBLY)
a.

Disconnect the i19 position control ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I113)Location & Routing

Click Connector(I113)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>No. 3 Global CAN Junction Connector

I113-8 (CANH) - I113-18 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG



OK

REPLACE POSITION CONTROL ECU ASSEMBLY

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - POSITION CONTROL ECU ASSEMBLY)

103.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - CERTIFICATION ECU [SMART KEY ECU ASSEMBLY])
a.

Disconnect the I39 certification ECU (smart key ECU assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I113)Location & Routing

Click Connector(I113)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>No. 3 Global CAN Junction Connector

I113-3 (CANH) - I113-13 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - CERTIFICATION ECU [SMART KEY ECU ASSEMBLY])

104.CHECK FOR OPEN IN CAN BUS WIRE (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - NO. 4 GLOBAL CAN JUNCTION CONNECTOR)
a.

Disconnect the I113 No. 3 global CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I113)Location & Routing

Click Connector(I113)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>No. 3 Global CAN Junction Connector

I113-2 (CANH) - I113-12 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

105.CHECK FOR OPEN IN CAN BUS WIRE (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU])

NG

106.CHECK FOR OPEN IN CAN BUS WIRE (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - NO. 3 GLOBAL CAN JUNCTION CONNECTOR)
105.CHECK FOR OPEN IN CAN BUS WIRE (NO. 3 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU])
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I113)Location & Routing

Click Connector(I113)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>No. 3 Global CAN Junction Connector

I113-1 (CANH) - I113-11 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

REPLACE NO. 3 GLOBAL CAN JUNCTION CONNECTOR

NG

108.CHECK FOR OPEN IN CAN BUS WIRE (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU) - NO. 3 GLOBAL CAN JUNCTION CONNECTOR)
106.CHECK FOR OPEN IN CAN BUS WIRE (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - NO. 3 GLOBAL CAN JUNCTION CONNECTOR)
a.

Reconnect the I113 No. 3 global CAN junction connector.


b.

Disconnect the I114 No. 4 global CAN junction connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I114)Location & Routing

Click Connector(I114)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>No. 4 Global CAN Junction Connector

I114-3 (CANH) - I114-13 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

107.CHECK FOR OPEN IN CAN BUS WIRE (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - NO. 11 GLOBAL CAN JUNCTION CONNECTOR)

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - NO. 3 GLOBAL CAN JUNCTION CONNECTOR)

107.CHECK FOR OPEN IN CAN BUS WIRE (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - NO. 11 GLOBAL CAN JUNCTION CONNECTOR)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I114)Location & Routing

Click Connector(I114)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>No. 4 Global CAN Junction Connector

I114-10 (CANH) - I114-20 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

REPLACE NO. 4 GLOBAL CAN JUNCTION CONNECTOR

NG

109.CHECK FOR OPEN IN CAN BUS WIRE (NO. 11 GLOBAL CAN JUNCTION CONNECTOR - NO. 4 GLOBAL CAN JUNCTION CONNECTOR)
108.CHECK FOR OPEN IN CAN BUS WIRE (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU) - NO. 3 GLOBAL CAN JUNCTION CONNECTOR)
a.

Reconnect the I113 No. 3 global CAN junction connector.


b.

Disconnect the I42 central gateway ECU (network gateway ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I42)Location & Routing

Click Connector(I42)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Network Gateway ECU

I42-7 (CA5H) - I42-8 (CA5L) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU) - NO. 3 GLOBAL CAN JUNCTION CONNECTOR)

109.CHECK FOR OPEN IN CAN BUS WIRE (NO. 11 GLOBAL CAN JUNCTION CONNECTOR - NO. 4 GLOBAL CAN JUNCTION CONNECTOR)
a.

Reconnect the I114 No. 4 global CAN junction connector.


b.

Disconnect the Q62 No. 11 global CAN junction connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(Q62)Location & Routing

Click Connector(Q62)Body>Air Conditioning Wiring Harness Assembly / Floor Wire / Step Rear Floor Wire RH / Theft Warning Sensor Cord Sub-Assembly>No. 11 Global CAN Junction Connector

Q62-1 (CANH) - Q62-7 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

110.CHECK FOR OPEN IN CAN BUS WIRE (NO. 11 GLOBAL CAN JUNCTION CONNECTOR - MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU])

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 11 GLOBAL CAN JUNCTION CONNECTOR - NO. 4 GLOBAL CAN JUNCTION CONNECTOR)

110.CHECK FOR OPEN IN CAN BUS WIRE (NO. 11 GLOBAL CAN JUNCTION CONNECTOR - MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU])
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(Q62)Location & Routing

Click Connector(Q62)Body>Air Conditioning Wiring Harness Assembly / Floor Wire / Step Rear Floor Wire RH / Theft Warning Sensor Cord Sub-Assembly>No. 11 Global CAN Junction Connector

Q62-2 (CANH) - Q62-8 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

REPLACE NO. 11 GLOBAL CAN JUNCTION CONNECTOR

NG

111.CHECK FOR OPEN IN CAN BUS WIRE (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) - NO. 11 GLOBAL CAN JUNCTION CONNECTOR)
111.CHECK FOR OPEN IN CAN BUS WIRE (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) - NO. 11 GLOBAL CAN JUNCTION CONNECTOR)
a.

Reconnect the Q62 No. 11 global CAN junction connector.


b.

Disconnect the I3 main body ECU (multiplex network body ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I3)Location & Routing

Click Connector(I3)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Main Body ECU

I3-2 (CANH) - I3-1 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) - NO. 11 GLOBAL CAN JUNCTION CONNECTOR)