Home › Drivetrain › AXLE AND DIFFERENTIAL › REAR AXLE SHAFT
RM38G0E _52 Drivetrain _100455 AXLE AND DIFFERENTIAL _0468067 REAR AXLE SHAFT A

AXLE AND DIFFERENTIAL  REAR AXLE SHAFT  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
C456683C03
3.667,1.573 4.938,2.208 1.271,0.635 1.281,2.688 1.49,2.688 1.49,2.688 1.656,2.073 false 6.146,3.521 6.333,3.094 6.333,3.094 6.667,3.094 false 4.917,2.479 5.198,1.927 5.198,1.927 5.479,1.927 false 3.615,3.792 3.615,4.271 false 2.688,3.833 2.521,3.833 2.521,3.833 2.521,3.427 false 1.708,2.833 1.917,2.833 1.917,2.833 1.917,2.229 false 1.427,1.552 2.177,1.354 2.177,1.354 3.51,1.354 true 5.021,3.333 5.396,2.865 5.396,2.865 5.688,2.865 false 6.406,0.302 6.792,0.302 false 6.458,0.667 6.75,0.667 false 6.802,1.01 6.469,1.01 false 5.677,2.396 5.719,2.271 5.719,2.271 5.875,2.271 false 4.24,1.875 4.604,1.875 false 3.417,2.333 3.677,2.333 false 6.271,0.146 6.552,0.427 0.281,0.281 18 false 1 6.302,0.51 6.74,0.792 0.438,0.281 18 false 2 6.708,2.927 7.146,3.208 0.438,0.281 18 false 3 6.302,0.854 6.573,1.104 0.271,0.25 18 false 4 3.875,1.24 4.313,1.521 0.438,0.281 18 false 5 4.677,1.74 5.115,2.021 0.438,0.281 18 false 6 6.146,2.094 6.354,2.354 0.208,0.26 18 false 7 3.844,1.729 4.073,1.906 0.229,0.177 10 false x 2 0.813,1.646 1.063,1.823 0.25,0.177 10 true x 4 5.771,1.792 6.052,2.146 0.281,0.354 18 false 8 6.021,2.688 6.375,3.042 0.354,0.354 18 false 9 2.938,3.677 3.25,3.958 0.313,0.281 18 false 10 1.583,2.74 1.74,2.938 0.156,0.198 10 false ● 3.719,2.24 3.875,2.438 0.156,0.198 10 false ● 0.896,2.604 1.052,2.802 0.156,0.198 10 false ● 3.479,4.26 4.031,4.615 0.552,0.354 18 false 11 0.979,2.521 1.531,2.875 0.552,0.354 18 false 12 3.698,1.604 4.01,1.802 0.313,0.198 10 false *A

Procedure Part Name Code
Z101186

Z101188

Z101187

1 PRECAUTION - (Click here) - -
2 DISABLE BRAKE CONTROL - - - (Click here)
3 REAR WHEEL - - - -
4 DRAIN BRAKE FLUID - - (Click here) -
5 REAR BRAKE FLEXIBLE HOSE - (Click here) - -
6 PARKING BRAKE ACTUATOR PROTECTOR ASSEMBLY 46170 - - -
7 NO. 2 PARKING BRAKE WIRE ASSEMBLY 890C0A (Click here) - -
8 REAR DISC BRAKE CYLINDER ASSEMBLY LH 47850 (Click here) - -
9 REAR DISC 42431 (Click here) - -
10 REAR SPEED SENSOR LH 89546 (Click here) - -
11 REAR AXLE SHAFT LH 42312 - - -
12 REAR AXLE SHAFT OIL SEAL LH 42312C (Click here) - -

*A w/ PARKING BRAKE ACTUATOR PROTECTOR ASSEMBLY - -
● Non-reusable part - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the rear axle shaft removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced:
Replacement Part or Procedure Necessary Procedures Effects/Inoperative when not Performed Link
Suspension, tires, etc. Rear television camera assembly optical axis (Back camera position setting) Parking assist monitor system (Click here)
·

Parking assist ECU initialization

·

Adjust steering angle

·

Rear television camera view adjustment (for Rear camera detection system)


Panoramic view monitor system (Click here)
Disconnect cable from negative battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
Multi-terrain monitor system (Click here)
Panoramic view monitor system (Click here)


NOTICE:
·

Immediately after installing the brake pads, the braking performance may be reduced. Always perform a road test in a safe place while paying attention to the surroundings.

·

After replacing the rear disc brake pads, the brake pedal may feel soft due to clearance between the rear disc brake pads and rear disc. Depress the brake pedal several times until the brake pedal feels firm.

·

When removing or installing the rear disc brake cylinder assembly, pushing back the disc brake piston may cause a large clearance between the brake pads and brake disc. When the brake pedal is depressed with a large clearance between the brake pads and the brake disc, DTC C13DB00, C13DC00, C13DD00, C13DE00, C140000 and/or C140A00 related to abnormal brake fluid pressure may be stored. Make sure to clear any DTCs after performing this procedure.

·

While the battery is connected, even if the ignition switch is off, the brake control system activates when the brake pedal is depressed or any door courtesy switch turns on. Therefore, when servicing the brake system components, do not operate the brake pedal or open/close the doors while the battery is connected.



HINT:

When the cable is disconnected/reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Stop and start system Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes). (Click here)
Lighting system (EXT) Cornering lights Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Lane tracing assist system
Lane departure alert system
Adaptive high beam system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor and expansion valve standard position is recognized. -

·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 1. PRECAUTION

Z101186

NOTICE:

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) battery terminal.

Click here(Click here)



Hide 2.DISABLE BRAKE CONTROL

Z101186

Click here(Click here)

Hide 3.REMOVE REAR WHEEL

Hide 4.DRAIN BRAKE FLUID

Z101186

Click here(Click here)

Hide 5.DISCONNECT REAR BRAKE FLEXIBLE HOSE

a.
C459034C01
0.906,0.125 1.073,0.417 0.167,0.292 18 true i 4.042,0.125 4.24,0.406 0.198,0.281 18 true ii

i.

Disconnect the brake tube from the rear flexible hose with union nut wrench while holding the flexible hose with a wrench.

NOTICE:
·

Do not bend or damage the brake tube.

·

Do not allow any foreign matter such as dirt and dust to enter the brake tube from the connecting point.




ii.

Remove the clip.



Hide 46170 6.REMOVE PARKING BRAKE ACTUATOR PROTECTOR ASSEMBLY (w/ PARKING BRAKE ACTUATOR PROTECTOR ASSEMBLY)

Hide 890C0A 7.DISCONNECT NO. 2 PARKING BRAKE WIRE ASSEMBLY

Z101186

(Click here)

Hide 47850 8.DISCONNECT DISC BRAKE CYLINDER ASSEMBLY REAR LH

a.
C456663C02
2.542,0.042 2.719,0.292 0.177,0.25 18 true i

i.

Remove the 2 bolts and disconnect the rear disc brake cylinder assembly LH.

NOTICE:
·

Do not twist or bend the rear flexible hose.

·

Do not disconnect the rear brake flexible hose from the rear disc brake cylinder assembly LH.





Hide 42431 9.REMOVE REAR DISC

Z101186

Click here(Click here)

Hide 89546 10.REMOVE REAR SPEED SENSOR LH

Z101186

Click here(Click here)

Hide 42312 11.REMOVE REAR AXLE SHAFT LH

a.
C456684C01
0,0 0,0 false


Hide 42312C 12.REMOVE REAR AXLE SHAFT OIL SEAL LH

a.
C456666C01
2.49,0.01 2.646,0.26 0.156,0.25 18 true i

i.

Using SST, tap out the rear axle shaft oil seal LH.

SST
09308-00010  

NOTICE:

Be careful not to damage the axle housing hole.