The main body ECU (multiplex network body ECU) controls the automatic high beam system based on signals received from the forward recognition camera.
First, confirm that there is no malfunction in the front radar sensor system.
Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.
When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.
Before troubleshooting, make sure that the low beam headlights and high beam headlights operate normally.
If the windshield glass is dirty, fogged up or has an oily film, the forward recognition camera may not operate properly, affecting the operation of systems that use the forward recognition camera.
When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle. As a result, a DTC may be stored.
When the forward recognition camera is replaced with a new one, make sure to read Before Starting Adjustment, then perform optical axis alignment for the forward recognition camera and clear the vehicle control history for each system.
Forward recognition camera axis alignment can be performed by using either One Time Recognition, Sequential Recognition or Driving Adjustment.
for Sequential Recognition:
Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>FRONT CAMERA>TARGET ADJUSTMENT(SEQUENTIAL RECOGNITION)
for One Time Recognition:
Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>FRONT CAMERA>TARGET ADJUSTMENT(ONE TIME RECOGNITION)
for Driving Adjustment:
Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>FRONT CAMERA>DRIVING ADJUSTMENT
Check the operation of the automatic high beam indicator.
Turn the ignition switch to ON.
Turn the light control switch to the AUTO or HEAD position.
Cover the automatic light control sensor to turn the low beam headlights on.
Move the dimmer switch to the low position.
Press the auto high beam switch.
| Result | Proceed to |
|---|---|
| OK (The automatic high beam indicator and the auto high beam switch indicator illuminate) | A |
| NG (Automatic high beam indicator does not illuminate) | B |
| NG (Auto high beam switch indicator does not illuminate) | C |
| NG (Automatic high beam indicator and auto high beam switch indicator do not operate) | D |
A
B
C
D
| *1 | Forward Recognition Camera (Automatic High Beam Sensor) |
| *2 | Work Light or Equivalent |
| *a | 100 mm (3.94 in.) or less |
Shine a light on the automatic high beam sensor.
If troubleshooting is being performed in a bright area, such as outside on a sunny day, it will not be necessary to perform this step.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Automatic High Beam Headlights Sensor Detection Status | Automatic high beam sensor current state | Undetected, N/A, No sens, Headlight, Taillight, Speed, Daytime, Village, Other sens, Change, Out of aim, SAE Mod, Aim adjust or LIN Err | Condition can be displayed | - |
| Tester Display |
|---|
| Automatic High Beam Headlights Sensor Detection Status |
"Daytime" is displayed on the GTS.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Cardboard or Equivalent Object |
| *a | 150 mm (5.91 in.) or more |
| *b | 3 mm (0.118 in.) or more |
Cover the automatic high beam sensor with an opaque object, such as cardboard.
Make sure that there is no clearance between the cardboard or equivalent object and the area of the windshield glass in front of the automatic high beam sensor.
If there is any clearance, light may shine on the automatic high beam sensor and the value of the Data List will not change.
Read the Data List according to the display on the GTS.
As it may take time for the values in the Data List to change, wait at least 10 seconds before reading the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Automatic High Beam Headlights Sensor Detection Status | Automatic high beam sensor current state | Undetected, N/A, No sens, Headlight, Taillight, Speed, Daytime, Village, Other sens, Change, Out of aim, SAE Mod, Aim adjust or LIN Err | Condition can be displayed | - |
| Tester Display |
|---|
| Automatic High Beam Headlights Sensor Detection Status |
"Speed" is displayed on the GTS.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
Using the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Front Recognition Camera High Temperature 2 | Whether high temperature malfunction of forward recognition camera exists or not | Not High Temperature or High Temperature | Not High Temperature: Approximately 65°C (149°F) or less High Temperature: Approximately 65°C (149°F) or higher |
If this item is "High Temperature", the automatic high beam system will be temporarily unavailable. If this does not improve even if the inside of the vehicle is left cooled for at least 10 minutes, the forward recognition camera may be malfunctioning.
|
| Tester Display |
|---|
| Front Recognition Camera High Temperature 2 |
Normal condition listed above is displayed.
When "High Temperature" is displayed, move the vehicle to a cool area and turn the ignition switch off to allow the temperature of the front recognition camera to decrease.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Perform the Active Test according to the display on the GTS.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Automatic High Beam Indicator (Green) | Automatic high beam indicator | OFF or ON | - |
| Tester Display |
|---|
| Automatic High Beam Indicator (Green) |
The automatic high beam indicator illuminates and turns off.
| Proceed to |
|---|
| OK |
| NG |
OK
for LHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
NG
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Auto High Beam Main Switch | Auto high beam switch signal | OFF or ON | OFF: Auto high beam switch not pressed ON: Auto high beam switch pressed |
- |
| Tester Display |
|---|
| Auto High Beam Main Switch |
Normal conditions listed above are displayed.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Automatic High Beam Headlights Sensor Detection Status | Automatic high beam sensor current state | Undetected, N/A, No sens, Headlight, Taillight, Speed, Daytime, Village, Other sens, Change, Out of aim, SAE Mod, Aim adjust or LIN Err | Condition can be displayed | - |
| Tester Display |
|---|
| Automatic High Beam Headlights Sensor Detection Status |
"Daytime" or "Speed" is displayed on the GTS.
| Proceed to |
|---|
| OK |
| NG |
OK
for LHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
NG
Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>AUTOMATIC HIGH BEAM MAIN SWITCH>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the I81 auto high beam switch connector.
Disconnect the I3 main body ECU (multiplex network body ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I81,I3)Location & Routingewd_type=routing;type=c,c;code=I81,I3 |
||
| I81-5 (+B) - I3-14 (AHBI) | Always | Below 1 Ω |
| I81-5 (+B) or I3-14 (AHBI) - Body ground | Always | 10 kΩ or higher |
| I81-2 (E) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
for LHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
NG