Home › Suspension › SUSPENSION CONTROL › ADAPTIVE VARIABLE SUSPENSION SYSTEM
RM38G0E _53 Suspension _100546 SUSPENSION CONTROL _0469072 ADAPTIVE VARIABLE SUSPENSION SYSTEM C

SUSPENSION CONTROL  ADAPTIVE VARIABLE SUSPENSION SYSTEM  C1715  Front Acceleration Sensor RH Malfunction  C1716  Front Acceleration Sensor LH Malfunction  C1717  Rear Acceleration Sensor Malfunction  C1796  Front Acceleration Sensor RH Malfunction (Test Mode DTC)  C1797  Front Acceleration Sensor LH Malfunction (Test Mode DTC)  C1798  Rear Acceleration Sensor Malfunction (Test Mode DTC)  


DESCRIPTION

The acceleration sensor (up and down G sensor) detects the upward and downward acceleration of the vehicle and outputs it as a voltage to the absorber control ECU.

The 3 up and down G sensors are installed in the driver side instrument panel, the passenger side instrument panel and the absorber control ECU.

Each up and down G sensor independently detects the upward and downward acceleration of the vehicle.

During a test mode inspection, the absorber control ECU reads the fluctuations in each sensor signal.

When a sensor signal does not fluctuate, test mode DTCs C1796, C1797 and C1798 remain stored.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Memory
C1715 Front Acceleration Sensor RH Malfunction One of the following conditions is met:
·

With the ignition switch to ON, a voltage of 5.5 V or higher, or 4.3 V or less is detected at the power source of the front acceleration sensor RH for 0.5 seconds.

·

With the ignition switch to ON, a voltage of 4.7 V or higher, or 0.3 V or less is detected at the front acceleration sensor RH for 1 second.

·

Sensor output value is +/- 0.0639 m/s2 continuously for 300 seconds.


·

Front acceleration sensor RH

·

Wire harness or connector

·

Absorber control ECU


Does not come on Yes
C1716 Front Acceleration Sensor LH Malfunction One of the following conditions is met:
·

With the ignition switch to ON, a voltage of 5.5 V or higher, or 4.3 V or less is detected at the power source of the front acceleration sensor LH for 0.5 seconds.

·

With the ignition switch to ON, a voltage of 4.7 V or higher, or 0.3 V or less is detected at the front acceleration sensor LH for 1 second.

·

Sensor output value is +/- 0.0639 m/s2 continuously for 300 seconds.


·

Front acceleration sensor LH

·

Wire harness or connector

·

Absorber control ECU


Does not come on Yes
C1717 Rear Acceleration Sensor Malfunction One of the following conditions is met:
·

With the ignition switch to ON, a voltage of 5.5 V or higher, or 4.3 V or less is detected at the power source of the rear acceleration sensor (absorber control ECU) for 0.5 seconds.

·

With the ignition switch to ON, a voltage of 4.7 V or higher, or 0.3 V or less is detected at the rear acceleration sensor (absorber control ECU) for 1 second.

·

Sensor output value is +/- 0.0639 m/s2 continuously for 300 seconds.


Absorber control ECU Does not come on Yes
C1796 Front Acceleration Sensor RH Malfunction (Test Mode DTC) With the vehicle stationary on a level surface, an acceleration sensor value that is within -1.96 to 1.96 m/s2 is not received from the front acceleration sensor RH for 1 second or more.
·

Front acceleration sensor RH

·

Wire harness or connector

·

Absorber control ECU


Test mode Test mode
C1797 Front Acceleration Sensor LH Malfunction (Test Mode DTC) With the vehicle stationary on a level surface, an acceleration sensor value that is within -1.96 to 1.96 m/s2 is not received from the front acceleration sensor LH for 1 second or more.
·

Front acceleration sensor LH

·

Wire harness or connector

·

Absorber control ECU


Test mode Test mode
C1798 Rear Acceleration Sensor Malfunction (Test Mode DTC) With the vehicle stationary on a level surface, an acceleration sensor value that is within -1.96 to 1.96 m/s2 is not received from the rear acceleration sensor (absorber control ECU) for 1 second or more. Absorber control ECU Test mode Test mode

DTC Detection Conditions: C1715
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3 Pattern 4 Pattern 5
Diagnosis Condition Ignition switch is ON ○ ○ ○ ○ ○
Malfunction Status Sensor power source voltage is 4.3 V or less ○ - - - -
Sensor power source voltage is 5.5 V or higher - ○ - - -
Output voltage is 0.3 V or less - - ○ - -
Output voltage is 4.7 V or higher - - - ○ -
Sensor output value is +/- 0.0638 m/s2 - - - - ○
Detection Time 0.5 seconds or more 0.5 seconds or more 1 second or more 1 second or more 300 seconds or more
Number of Trips 1 trip 1 trip 1 trip 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


DTC Detection Conditions: C1716
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3 Pattern 4 Pattern 5
Diagnosis Condition Ignition switch is ON ○ ○ ○ ○ ○
Malfunction Status Sensor power source voltage is 4.3 V or less ○ - - - -
Sensor power source voltage is 5.5 V or higher - ○ - - -
Output voltage is 0.3 V or less - - ○ - -
Output voltage is 4.7 V or higher - - - ○ -
Sensor output value is +/- 0.0638 m/s2 - - - - ○
Detection Time 0.5 seconds or more 0.5 seconds or more 1 second or more 1 second or more 300 seconds or more
Number of Trips 1 trip 1 trip 1 trip 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


DTC Detection Conditions: C1717
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3 Pattern 4 Pattern 5
Diagnosis Condition Ignition switch is ON ○ ○ ○ ○ ○
Malfunction Status Sensor power source voltage is 4.3 V or less ○ - - - -
Sensor power source voltage is 5.5 V or higher - ○ - - -
Output voltage is 0.3 V or less - - ○ - -
Output voltage is 4.7 V or higher - - - ○ -
Sensor output value is +/- 0.0638 m/s2 - - - - ○
Detection Time 0.5 seconds or more 0.5 seconds or more 1 second or more 1 second or more 300 seconds or more
Number of Trips 1 trip 1 trip 1 trip 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


WIRING DIAGRAM

C306495E35
1.396,0.813 2.01,1.01 0.615,0.198 10 false SGFR 1.479,1.271 1.938,1.469 0.458,0.198 10 false SGG 1.49,1.729 1.948,1.927 0.458,0.198 10 false SGB 0.51,2.24 0.823,2.438 0.313,0.198 10 false Q15 0.51,2.417 3.094,2.583 2.583,0.167 10 false Acceleration Sensor Assembly RH 1.427,3.656 2.042,3.854 0.615,0.198 10 false SGFL 1.469,4.125 2.083,4.323 0.615,0.198 10 false SGG 1.479,4.583 1.938,4.781 0.458,0.198 10 false SGB 0.552,5.156 1.01,5.354 0.458,0.198 10 false S10 1.917,0.698 2.073,0.896 0.156,0.198 10 false 1 1.917,1.177 2.073,1.375 0.156,0.198 10 false 2 1.917,1.646 2.073,1.844 0.156,0.198 10 false 3 1.917,3.563 2.073,3.76 0.156,0.198 10 false 1 1.917,4.031 2.073,4.229 0.156,0.198 10 false 2 1.917,4.49 2.073,4.688 0.156,0.198 10 false 3 5.479,0.802 6.094,1 0.615,0.198 10 false SGS1 5.479,1.271 6.094,1.469 0.615,0.198 10 false SGG1 5.49,1.729 6.104,1.927 0.615,0.198 10 false SGB1 5.479,3.667 6.094,3.865 0.615,0.198 10 false SGS2 5.479,4.135 6.094,4.333 0.615,0.198 10 false SGG2 5.479,4.583 6.094,4.781 0.615,0.198 10 false SGB2 5.083,5.917 6.802,6.292 1.719,0.375 10 false Absorber Control ECU 5.083,5.74 5.396,5.927 0.313,0.188 10 false Q11 5.198,0.708 5.51,0.906 0.313,0.198 10 false 23 5.198,1.167 5.51,1.365 0.313,0.198 10 false 22 5.198,1.625 5.51,1.823 0.313,0.198 10 false 14 5.198,3.552 5.51,3.75 0.313,0.198 10 false 25 5.198,4.01 5.51,4.208 0.313,0.198 10 false 24 5.188,4.469 5.5,4.667 0.313,0.198 10 false 15 0.542,5.344 3.125,5.51 2.583,0.167 10 false Acceleration Sensor Assembly LH

CAUTION / NOTICE / HINT

NOTICE:
·

Before performing troubleshooting, inspect the connectors of related circuits.

·

If DTC C1782 (Power Source Voltage Malfunction) is output at the same time, perform troubleshooting for C1782 first.

Click hereSuspension>SUSPENSION CONTROL>ADAPTIVE VARIABLE SUSPENSION SYSTEM>C1782

·

Before replacing the absorber control ECU, perform all of the following:

-

DTC inspection.

*

If no malfunctions are found in other areas, replace the absorber control ECU.



·

After replacing the absorber control ECU with a new one, perform registration of vehicle identification information.

Click hereSuspension>SUSPENSION CONTROL>ADAPTIVE VARIABLE SUSPENSION SYSTEM>TEST MODE PROCEDURE



PROCEDURE

1.READ VALUE USING GTS ((UP & DOWN) G SENSOR)
a.

Read the Data List.

Chassis > Adaptive Variable Suspension System > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
(Up&Down)G Sensor FR Front acceleration sensor RH (up and down) Min.: -1045.29 m/s2
Max.: 1045.26 m/s2
-0.98 to 0.98 m/s2
when stationary
The value changes when the vehicle (front RH) is bounced.
(Up&Down)G Sensor FL Front acceleration sensor LH (up and down) Min.: -1045.29 m/s2
Max.: 1045.26 m/s2
-0.98 to 0.98 m/s2
when stationary
The value changes when the vehicle (front LH) is bounced.
(Up&Down)G Sensor Rear Rear acceleration sensor (up and down) Min.: -1045.29 m/s2
Max.: 1045.26 m/s2
-0.98 to 0.98 m/s2
when stationary
The value changes when the vehicle (rear) is bounced.
Chassis > Adaptive Variable Suspension System > Data List
Tester Display
(Up&Down)G Sensor FR
(Up&Down)G Sensor FL
(Up&Down)G Sensor Rear
50003 171 1,2,3
OK:

The values are as specified in the normal condition column.



Result:
Result Proceed to
OK A
NG (front RH or front LH) B
NG (rear) C



A

2.CHECK FOR DTCS

B

3.INSPECT FRONT ACCELERATION SENSOR

C

REPLACE ABSORBER CONTROL ECU

2.CHECK FOR DTCS
a.

Clear the DTCs.

Chassis > Adaptive Variable Suspension System > Clear DTCs
50002 171

b.

Turn the ignition switch off.


c.

Check for DTCs.

Chassis > Adaptive Variable Suspension System > Trouble Codes
50001 171

Result:
Result Proceed to
DTCs are output (front RH or front LH) A
DTCs are output (rear) B
DTCs are not output C



A

3.INSPECT FRONT ACCELERATION SENSOR

B

REPLACE ABSORBER CONTROL ECU

C

3.INSPECT FRONT ACCELERATION SENSOR
a.

Turn the ignition switch off.


b.

Remove the front acceleration sensor RH or front acceleration sensor LH.

Click hereSuspension>SUSPENSION CONTROL>FRONT ACCELERATION SENSOR>REMOVAL


c.

Inspect the front acceleration sensor RH or front acceleration sensor LH.

Click hereSuspension>SUSPENSION CONTROL>FRONT ACCELERATION SENSOR>INSPECTION


Result:
Result Proceed to
OK A
Front acceleration sensor RH malfunction B
Front acceleration sensor LH malfunction C



A

4.CHECK HARNESS AND CONNECTOR (FRONT ACCELERATION SENSOR - ABSORBER CONTROL ECU)

B

REPLACE FRONT ACCELERATION SENSOR RH

C

REPLACE FRONT ACCELERATION SENSOR LH

4.CHECK HARNESS AND CONNECTOR (FRONT ACCELERATION SENSOR - ABSORBER CONTROL ECU)
a.

Check the front acceleration sensor RH harness and connector (when DTC C1715 is output).

i.

Disconnect the Q11 absorber control ECU connector.


ii.

Disconnect the Q15 front acceleration sensor RH connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(Q15,Q11)Location & Routing

Click Connector(Q15)Instrument Panel>Floor Wire / No. 1 Cooler Wiring Harness Sub-Assembly>Acceleration Sensor RH

Click Connector(Q11)Body>Air Conditioning Wiring Harness Assembly / Floor Wire / Step Rear Floor Wire RH / Theft Warning Sensor Cord Sub-Assembly>Absorber Control ECU

Q15-1 (SGFR) - Q11-23 (SGS1) Always Below 1 Ω
Q15-2 (SGG) - Q11-22 (SGG1) Always Below 1 Ω
Q15-3 (SGB) - Q11-14 (SGB1) Always Below 1 Ω
Q15-1 (SGFR) or Q11-23 (SGS1) - Body ground Always 10 kΩ or higher
Q15-2 (SGG) or Q11-22 (SGG1) - Body ground Always 10 kΩ or higher
Q15-3 (SGB) or Q11-14 (SGB1) - Body ground Always 10 kΩ or higher




b.

Check the front acceleration sensor LH harness and connector (when DTC C1716 is output).

i.

Disconnect the Q11 absorber control ECU connector.


ii.

Disconnect the S10 front acceleration sensor LH connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(S10,Q11)Location & Routing

Click Connector(S10)Instrument Panel>No. 2 Floor Wire>Acceleration Sensor LH

Click Connector(Q11)Body>Air Conditioning Wiring Harness Assembly / Floor Wire / Step Rear Floor Wire RH / Theft Warning Sensor Cord Sub-Assembly>Absorber Control ECU

S10-1 (SGFL) - Q11-25 (SGS2) Always Below 1 Ω
S10-2 (SGG) - Q11-24 (SGG2) Always Below 1 Ω
S10-3 (SGB) - Q11-15 (SGB2) Always Below 1 Ω
S10-1 (SGFL) or Q11-25 (SGS2) - Body ground Always 10 kΩ or higher
S10-2 (SGG) or Q11-24 (SGG2) - Body ground Always 10 kΩ or higher
S10-3 (SGB) or Q11-15 (SGB2) - Body ground Always 10 kΩ or higher




Result:
Proceed to
OK
NG



OK

REPLACE ABSORBER CONTROL ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR