Home › Engine / Hybrid System › 1GR-FE (ENGINE CONTROL) › SFI SYSTEM
RM38G0E _51 Engine / Hybrid System _100527 1GR-FE ENGINE CONTROL _0469186 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P001700  Crankshaft Position - Camshaft Position Correlation Bank 1 Sensor B  P001900  Crankshaft Position - Camshaft Position Correlation Bank 2 Sensor B  


DESCRIPTION

In the VVT (Variable Valve Timing) system, the appropriate exhaust valve open and close timing is controlled by the ECM. The ECM performs exhaust valve control by performing the following: 1) controlling the camshaft and camshaft timing oil control valve, and operating the camshaft timing gear; and 2) changing the relative positions of the camshaft and crankshaft.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Note
P001700 Crankshaft Position - Camshaft Position Correlation Bank 1 Sensor B Deviations in the crankshaft position sensor and VVT sensor 1 (for exhaust camshaft) signals (2 trip detection logic).
·

Valve timing

·

Camshaft timing oil control valve assembly (for exhaust side)

·

Oil control valve filter

·

Camshaft timing exhaust gear assembly

·

ECM


Comes on / Does not come on SAE: P0017
P001900 Crankshaft Position - Camshaft Position Correlation Bank 2 Sensor B Deviations in the crankshaft position sensor and VVT sensor 2 (for exhaust camshaft) signals (2 trip detection logic).
·

Valve timing

·

Camshaft timing oil control valve assembly (for exhaust side)

·

Oil control valve filter

·

Camshaft timing exhaust gear assembly

·

ECM


Comes on / Does not come on SAE: P0019

MONITOR DESCRIPTION

To monitor the correlation of the exhaust camshaft position and crankshaft position, the ECM checks the VVT learned value while the engine is idling. The VVT learned value is calibrated based on the camshaft position and crankshaft position. The exhaust valve timing is set to the most advanced angle while the engine is idling. If the VVT learned value is out of the specified range in consecutive driving cycles, the ECM illuminates the MIL and stores DTC P001700 (Bank 1) or P001900 (Bank 2).

CONFIRMATION DRIVING PATTERN

A197314E49
4.26,1.115 4.604,0.49 4.604,0.49 4.75,0.49 false 0.156,0.656 1.177,0.844 1.021,0.188 10 Vehicle Speed 1.542,2.146 1.75,2.344 0.208,0.198 10 [A] 2.167,1.656 2.396,1.823 0.229,0.167 10 [B] 3.188,1.646 3.396,1.802 0.208,0.156 10 [C] 3.823,3.01 4.031,3.167 0.208,0.156 10 [D] 4.677,0.854 4.875,1.052 0.198,0.198 10 [E] 5.656,1.615 5.854,1.813 0.198,0.198 10 [F] 6.375,3.021 6.615,3.208 0.24,0.188 10 [G] 0.667,1.75 1.115,1.927 0.448,0.177 10 Idling 4.813,0.313 6.292,0.677 1.479,0.365 10 There is no designated vehicle speed 0.208,2.031 1.135,2.344 0.927,0.313 10 Ignition Switch ON 1.906,2.5 2.719,3.063 0.813,0.563 10 Warming up the engine 2.74,2.521 3.896,2.688 1.156,0.167 10 5 minutes or more 5.271,2.531 6.427,2.698 1.156,0.167 10 5 minutes or more 4.125,2.563 5.021,2.729 0.896,0.167 10 2 to 3 minutes

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on [A].

6.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher [B].

7.

Idle the engine for 5 minutes or more [C].

8.

Enter the following menus: Powertrain / Engine / Trouble Codes [D].

9.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



10.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

11.

Input the DTC: P001700 or P001900.

12.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [E] through [G].



13.

Drive the vehicle for 2 to 3 minutes [E].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


14.

Idle the engine for 5 minutes or more [F].

15.

Enter the following menus: Powertrain / Engine / Trouble Codes [G].

16.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



17.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.




CAUTION / NOTICE / HINT

HINT:
·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

Bank 1 refers to the bank that includes the No. 1 cylinder*.

*: The No. 1 cylinder is the cylinder which is farthest from the transmission.

·

Bank 2 refers to the bank that does not include the No. 1 cylinder.



PROCEDURE

1.CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P001700 OR P001900)
a.

Turn the ignition switch to ON.


b.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
P001700 or P001900 is output A
P001700 or P001900 and other DTCs are output B


HINT:

If any DTCs other than P001700 or P001900 are output, troubleshoot those DTCs first.




A

2.PERFORM ACTIVE TEST USING GTS (OPERATE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY FOR EXHAUST SIDE)

B

2.PERFORM ACTIVE TEST USING GTS (OPERATE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY FOR EXHAUST SIDE)
a.

Start the engine.


b.

Warm up the engine.


c.

Turn the A/C on.


d.

Perform the Active Test. Check that the displacement angle varies.

Powertrain > Engine > Active Test
Active Test Display
Control the Exhaust VVT OCV Duty Ratio Bank 1
Data List Display
Exhaust VVT Change Angle Bank 1
50004 372 5 398
Powertrain > Engine > Active Test
Active Test Display
Control the Exhaust VVT OCV Duty Ratio Bank 2
Data List Display
Exhaust VVT Change Angle Bank 2
50004 372 46 470
OK:

Displacement angle varies.



Result:
Proceed to
OK
NG



OK

3.CHECK ENGINE MECHANICAL SYSTEM

NG

4.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR EXHAUST SIDE)
3.CHECK ENGINE MECHANICAL SYSTEM
a.

Check for mechanical malfunctions that affect the valve timing, such as a jumped tooth or stretching of the timing chain.


Result:
Proceed to
OK
NG



OK

7.CHECK WHETHER DTC OUTPUT RECURS (DTC P001700 OR P001900)

NG

REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA

4.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR EXHAUST SIDE)
a.

Inspect the camshaft timing oil control valve assembly.

Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>CAMSHAFT OIL CONTROL VALVE>INSPECTION


Result:
Proceed to
OK
NG



OK

5.CHECK OIL CONTROL VALVE FILTER AND OIL PIPE

NG

REPLACE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY

5.CHECK OIL CONTROL VALVE FILTER AND OIL PIPE
A225778C03
0.042,0 0.354,0.198 0.313,0.198 10 false *1 0.031,2.344 0.344,2.542 0.313,0.198 10 false *2
*1 No. 1 Oil Pipe
*2 No. 2 Oil Pipe


a.

Remove the No. 1 or No. 2 oil pipe.


b.

Remove the oil control valve filter.


c.

Check that the filter and pipe are not clogged.

OK:

The filter and pipe are not clogged.



Result:
Proceed to
OK
NG



OK

6.INSPECT CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY

NG

REPLACE OIL CONTROL VALVE FILTER OR OIL PIPE

6.INSPECT CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY
a.

Inspect the camshaft timing exhaust gear assembly.

Click hereEngine / Hybrid System>1GR-FE (ENGINE MECHANICAL)>ENGINE UNIT>INSPECTION

HINT:

Perform "Inspection After Repair" after replacing the camshaft timing exhaust gear assembly.

Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

7.CHECK WHETHER DTC OUTPUT RECURS (DTC P001700 OR P001900)

NG

REPLACE CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY

7.CHECK WHETHER DTC OUTPUT RECURS (DTC P001700 OR P001900)
a.

Turn the ignition switch to ON.


b.

Clear the DTCs

Powertrain > Engine > Clear DTCs
50002 372

c.

Start the engine and warm it up.


d.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


e.

Read the pending DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
DTCs are not output A
DTC P001700 or P001900 is output B


HINT:

DTC P001700 or P001900 is stored when foreign objects in the engine oil are caught in some parts of the system. These codes will remain stored even if the system returns to normal after a short time. These foreign objects are then captured by the oil filter, thus eliminating the source of the problem.




A

END

B