Home › Engine / Hybrid System › 1GR-FE (ENGINE CONTROL) › SFI SYSTEM
RM38G0E _51 Engine / Hybrid System _100527 1GR-FE ENGINE CONTROL _0469186 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P001100  Camshaft Position "A" - Timing Over-Advanced or System Performance Bank 1  P001200  Camshaft Position "A" - Timing Over-Retarded Bank 1  P002100  Camshaft Position "A" - Timing Over-Advanced or System Performance Bank 2  P002200  Camshaft Position "A" - Timing Over-Retarded Bank 2  


DESCRIPTION

Refer to DTC P001013.

Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>P001013

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Note
P001100 Camshaft Position "A" - Timing Over-Advanced or System Performance Bank 1 Intake valve timing is stuck at a certain value when in the advance range (1 trip detection logic).
·

Valve timing

·

Camshaft timing oil control valve assembly (for intake camshaft of bank 1)

·

Oil control valve filter

·

Oil pipe

·

Camshaft timing gear assembly (bank 1)

·

ECM


Comes on SAE: P0011
P001200 Camshaft Position "A" - Timing Over-Retarded Bank 1 Intake valve timing is stuck at a certain value when in the retard range (2 trip detection logic).
·

Valve timing

·

Camshaft timing oil control valve assembly (for intake camshaft of bank 1)

·

Oil control valve filter

·

Oil pipe

·

Camshaft timing gear assembly (bank 1)

·

ECM


Comes on SAE: P0012
P002100 Camshaft Position "A" - Timing Over-Advanced or System Performance Bank 2 Intake valve timing is stuck at a certain value when in the advance range (1 trip detection logic).
·

Valve timing

·

Camshaft timing oil control valve assembly (for intake camshaft of bank 2)

·

Oil control valve filter

·

Oil pipe

·

Camshaft timing gear assembly (bank 2)

·

ECM


Comes on SAE: P0021
P002200 Camshaft Position "A" - Timing Over-Retarded Bank 2 Intake valve timing is stuck at a certain value when in the retard range (2 trip detection logic).
·

Valve timing

·

Camshaft timing oil control valve assembly (for intake camshaft of bank 2)

·

Oil control valve filter

·

Oil pipe

·

Camshaft timing gear assembly (bank 2)

·

ECM


Comes on SAE: P0022

MONITOR DESCRIPTION

The ECM optimizes the intake valve timing using the Variable Valve Timing (VVT) system to control the intake camshaft. The VVT system includes the ECM, camshaft timing oil control valve assembly (for intake camshaft) and VVT controller (camshaft timing gear assembly). The ECM sends a target duty-cycle control signal to the camshaft timing oil control valve assembly (for intake camshaft). This control signal regulates the oil pressure supplied to the VVT controller. The VVT controller can advance or retard the intake camshaft.

If the difference between the target and actual intake valve timing is large, and changes in the actual intake valve timing are small, the ECM interprets this as the VVT controller stuck malfunction and stores a DTC.

Example:

A DTC is stored when the following conditions 1 and 2 are met:

1. It takes 5 seconds or more to change the valve timing by 5°CA.

2. After the above condition 1 is met, the OCV is forcibly activated 63 times or more (when the vehicle is idling, this takes approximately 100 seconds).



DTCs P001100 and P002100 (Advanced Camshaft Timing) are subject to 1 trip detection logic.

DTCs P001200 and P002200 (Retarded Camshaft Timing) are subject to 2 trip detection logic.

These DTCs indicate that the VVT controller cannot operate properly due to a camshaft timing oil control valve assembly (for intake camshaft) malfunction or the presence of foreign matter in the camshaft timing oil control valve assembly (for intake camshaft).

CONFIRMATION DRIVING PATTERN

A232050E42
6.719,2.625 6.333,3.49 6.333,3.49 6.25,3.49 false 4.156,2.646 3.833,3.51 3.833,3.51 3.771,3.51 false 1.365,2.354 1.604,2.5 0.24,0.146 10 [A] 1.875,2.042 2.115,2.188 0.24,0.146 10 [B] 3.01,1.031 3.25,1.177 0.24,0.146 10 [C] 4.052,2.313 4.292,2.458 0.24,0.146 10 [D] 4.281,3.135 4.521,3.281 0.24,0.146 10 [E] 5.448,2.219 5.688,2.365 0.24,0.146 10 [F]* 6.615,2.302 6.854,2.448 0.24,0.146 10 [G] 6.833,3.156 7.073,3.302 0.24,0.146 10 [H] 0.156,2.313 1.125,2.646 0.969,0.333 10 Ignition Switch ON 0.708,2.052 1.094,2.24 0.385,0.188 10 Idling 0.177,1.094 1.135,1.438 0.958,0.344 10 Approximately 60 km/h 0.167,0.375 1.115,0.542 0.948,0.167 10 Vehicle Speed 1.615,2.771 2.417,2.969 0.802,0.198 10 Warming up 2.563,2.771 3.802,2.917 1.24,0.146 10 10 minutes or more 2.552,3.427 3.844,3.604 1.292,0.177 10 3 minutes or more 2.375,0.021 7.031,0.542 4.656,0.521 10 *: Repeat the pattern of accelerating the vehicle from rest to approximately 60 km/h (depress the accelerator pedal by a large amount) and then decelerating the vehicle 10 to 15 times. 5,3.385 6.188,3.563 1.188,0.177 10 3 minutes or more

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on [A].

6.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher [B].

7.

Drive the vehicle at approximately 60 km/h (37 mph) for 10 minutes or more [C].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


8.

Idle the engine for 3 minutes or more [D].

9.

Enter the following menus: Powertrain / Engine / Trouble Codes [E].

10.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

12.

Input the DTC: P001100, P001200, P002100 or P002200.

13.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [F] through [H].



14.

Repeat the pattern of accelerating the vehicle from rest to approximately 60 km/h (37 mph) and then decelerating the vehicle 10 to 15 times [F].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

Depress the accelerator pedal by a large amount.


15.

Idle the engine for 3 minutes or more [G].

16.

Enter the following menus: Powertrain / Engine / Trouble Codes [H].

17.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



18.

Check the DTC judgment result again.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.




CAUTION / NOTICE / HINT

HINT:
Abnormal Bank Timing Over Advanced
(Valve timing is out of specified range)
Timing Over Retarded
(Valve timing is out of specified range)
Bank 1 P001100 P001200
Bank 2 P002100 P002200

·

If DTC P001100 or P001200 is output, check the VVT system (for intake camshaft of bank 1) circuit.

·

If DTC P002100 or P002200 is output, check the VVT system (for intake camshaft of bank 2) circuit.

·

Bank 1 refers to the bank that includes the No. 1 cylinder*.

*: The No. 1 cylinder is the cylinder which is farthest from the transmission.

·

Bank 2 refers to the bank that does not include the No. 1 cylinder.

·

DTC P001100, P001200, P002100 or P002200 may be stored when foreign matter in the engine oil is caught in some parts of the system. The DTC will remain stored even if the system returns to normal after a short time. That foreign matter may then be captured by the oil filter.

·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P001100, P001200, P002100 OR P002200)
a.

Turn the ignition switch to ON.


b.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
DTC P001100, P001200, P002100 or P002200 is output A
DTC P001100, P001200, P002100 or P002200 and other DTCs are output B


HINT:

If any DTCs other than P001100, P001200, P002100 or P002200 are output, troubleshoot those DTCs first.




A

2.PERFORM ACTIVE TEST USING GTS (CONTROL THE INTAKE VVT OCV DUTY RATIO)

B

2.PERFORM ACTIVE TEST USING GTS (CONTROL THE INTAKE VVT OCV DUTY RATIO)
a.

Start the engine.


b.

Turn the A/C switch on.


c.

Check the engine speed while operating the camshaft timing oil control valve (for intake camshaft) using the GTS.

Powertrain > Engine > Active Test
Tester Display
Control the Intake VVT OCV Duty Ratio Bank 1
50004 372 4
Powertrain > Engine > Active Test
Tester Display
Control the Intake VVT OCV Duty Ratio Bank 2
50004 372 45
OK:
GTS Operation Engine Condition
0% Normal engine speed
100% Engine idles roughly or stalls


HINT:

Refer to "Data List / Active Test" [Intake VVT OCV Control Duty Ratio Bank 1, Intake VVT Change Angle Bank 1, Intake VVT OCV Control Duty Ratio Bank 2, and Intake VVT Change Angle Bank 2].

Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>DATA LIST / ACTIVE TEST



Result:
Proceed to
OK
NG



OK

3.CHECK WHETHER DTC OUTPUT RECURS (DTC P001100, P001200, P002100 OR P002200)

NG

4.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR INTAKE CAMSHAFT)
3.CHECK WHETHER DTC OUTPUT RECURS (DTC P001100, P001200, P002100 OR P002200)
a.

Turn the ignition switch to ON.


b.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

c.

Turn the ignition switch off and wait for at least 30 seconds.


d.

Turn the ignition switch to ON.


e.

Start the engine and warm it up.


f.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


g.

Read the pending DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
DTCs are not output A
DTC P001100, P001200, P002100 or P002200 is output B


HINT:

DTC P001100, P001200, P002100 or P002200 may be stored when foreign matter in the engine oil is caught in some parts of the system. The DTC will remain stored even if the system returns to normal after a short time. That foreign matter may then be captured by the oil filter.




A

B

5.CHECK VALVE TIMING (CHECK FOR LOOSE TIMING CHAIN AND JUMPED TEETH)
4.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR INTAKE CAMSHAFT)
a.

Inspect the camshaft timing oil control valve assembly (for intake camshaft).

Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>CAMSHAFT OIL CONTROL VALVE>INSPECTION


Result:
Proceed to
OK
NG



OK

5.CHECK VALVE TIMING (CHECK FOR LOOSE TIMING CHAIN AND JUMPED TEETH)

NG

REPLACE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR INTAKE CAMSHAFT)

5.CHECK VALVE TIMING (CHECK FOR LOOSE TIMING CHAIN AND JUMPED TEETH)
A385296C01
1.26,0.813 1.5,0.365 true 1.24,1.083 1.5,0.365 true 1.969,1.458 2.188,0.875 true 1.969,1.448 2.167,1.219 true 2.854,3.271 3.125,2.844 true 2.865,3.229 3.052,2.833 true 2.865,3.25 3.042,2.615 true 2.208,2.51 2.479,2.135 true 2.219,2.906 2.469,2.135 true 1.531,0.208 1.844,0.406 0.313,0.198 10 false *1 1.854,1.5 2.167,1.698 0.313,0.198 10 false *1 2.719,3.25 3.031,3.448 0.313,0.198 10 false *1 2.448,1.99 2.76,2.188 0.313,0.198 10 false *1
*1 Timing Mark


a.

Remove the cylinder head cover sub-assembly and cylinder head cover sub-assembly LH.

Click hereEngine / Hybrid System>1GR-FE (ENGINE MECHANICAL)>CAMSHAFT>REMOVAL


b.

Turn the crankshaft pulley, and align its groove with the "0" timing mark of the timing chain cover.


c.

Check that the timing marks of the camshaft timing gear assemblies and camshaft timing sprockets are aligned with the timing marks of the bearing cap as shown in the illustration.

HINT:

If the timing marks are not as shown, turn the crankshaft one revolution clockwise.


OK:

The timing marks on the camshaft timing gear assemblies and camshaft timing sprockets are aligned as shown in the illustration.


HINT:

If the result is not as specified, check for mechanical malfunctions that may have affected the valve timing, such as a jumped tooth or stretching of the timing chain.



Result:
Proceed to
OK
NG



OK

6.INSPECT OIL CONTROL VALVE FILTER AND OIL PIPE

NG

9.CHECK ENGINE MECHANICAL SYSTEM
6.INSPECT OIL CONTROL VALVE FILTER AND OIL PIPE
A225778C03
0.042,0 0.354,0.198 0.313,0.198 10 false *1 0.031,2.344 0.344,2.542 0.313,0.198 10 false *2
*1 No. 1 Oil Pipe
*2 No. 2 Oil Pipe


a.

Remove the No. 1 or No. 2 oil pipe.


b.

Remove the oil control valve filter.


c.

Check that the filter and pipe are not clogged.

OK:

The filter and pipe are not clogged.



d.

Reinstall the oil control valve filter.


e.

Reinstall the No. 1 or No. 2 oil pipe.


Result:
Proceed to
OK
NG



OK

7.REPLACE CAMSHAFT TIMING GEAR ASSEMBLY

NG

7.REPLACE CAMSHAFT TIMING GEAR ASSEMBLY
a.

Replace the camshaft timing gear assembly (bank 1 or bank 2).

Click hereEngine / Hybrid System>1GR-FE (ENGINE MECHANICAL)>CAMSHAFT>REMOVAL

HINT:

Perform "Inspection After Repair" after replacing the camshaft timing gear assembly.

Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
NEXT



NEXT

8.CHECK WHETHER DTC OUTPUT RECURS (DTC P001100, P001200, P002100 OR P002200)
8.CHECK WHETHER DTC OUTPUT RECURS (DTC P001100, P001200, P002100 OR P002200)
a.

Turn the ignition switch to ON.


b.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

c.

Turn the ignition switch off and wait for at least 30 seconds.


d.

Turn the ignition switch to ON.


e.

Start the engine and warm it up.


f.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


g.

Read the pending DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
DTCs are not output A
DTC P001100, P001200, P002100 or P002200 is output B




A

END

B

9.CHECK ENGINE MECHANICAL SYSTEM
a.

Check for mechanical malfunctions that affect the valve timing, such as a jumped tooth or stretching of the timing chain.


Result:
Proceed to
OK
NG



OK

10.CHECK WHETHER DTC OUTPUT RECURS (DTC P001100, P001200, P002100 OR P002200)

NG

REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA

10.CHECK WHETHER DTC OUTPUT RECURS (DTC P001100, P001200, P002100 OR P002200)
a.

Turn the ignition switch to ON.


b.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

c.

Turn the ignition switch off and wait for at least 30 seconds.


d.

Turn the ignition switch to ON.


e.

Start the engine and warm it up.


f.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


g.

Read the pending DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
DTCs are not output A
DTC P001100, P001200, P002100 or P002200 is output B




A

B