Home › Engine / Hybrid System › 1GR-FE (ENGINE CONTROL) › SFI SYSTEM
RM38G0E _51 Engine / Hybrid System _100527 1GR-FE ENGINE CONTROL _0469186 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P001600  Crankshaft Position - Camshaft Position Correlation Bank 1 Sensor A  P001800  Crankshaft Position - Camshaft Position Correlation Bank 2 Sensor A  


DESCRIPTION

In the VVT (Variable Valve Timing) system, the appropriate intake valve open and close timing is controlled by the ECM. The ECM performs intake valve control by performing the following: 1) controlling the intake camshaft and camshaft timing oil control valve assembly (for intake camshaft), and operating the camshaft timing gear assembly; and 2) changing the relative positions of the camshaft and crankshaft.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Note
P001600 Crankshaft Position - Camshaft Position Correlation Bank 1 Sensor A Deviation in the crankshaft position sensor signal and VVT sensor (for intake camshaft of bank 1) signal (2 trip detection logic).
·

Valve timing

·

Camshaft timing oil control valve assembly (for intake camshaft of bank 1)

·

Oil control valve filter

·

Oil pipe

·

Camshaft timing gear assembly (bank 1)

·

ECM


Comes on / Does not come on SAE: P0016
P001800 Crankshaft Position - Camshaft Position Correlation Bank 2 Sensor A Deviation in the crankshaft position sensor signal and VVT sensor (for intake camshaft of bank 2) signal (2 trip detection logic).
·

Valve timing

·

Camshaft timing oil control valve assembly (for intake camshaft of bank 2)

·

Oil control valve filter

·

Oil pipe

·

Camshaft timing gear assembly (bank 2)

·

ECM


Comes on / Does not come on SAE: P0018

MONITOR DESCRIPTION

To monitor the correlation of the intake camshaft position and crankshaft position, the ECM checks the VVT learned value while the engine is idling. The VVT learned value is calibrated based on the camshaft position and crankshaft position. The intake valve timing is set to the most retarded angle while the engine is idling. If the VVT learned value is out of the specified range in consecutive driving cycles, the ECM stores a DTC.

CONFIRMATION DRIVING PATTERN

A197314E49
4.26,1.115 4.604,0.49 4.604,0.49 4.75,0.49 false 0.156,0.656 1.177,0.844 1.021,0.188 10 Vehicle Speed 1.542,2.146 1.75,2.344 0.208,0.198 10 [A] 2.167,1.656 2.396,1.823 0.229,0.167 10 [B] 3.188,1.646 3.396,1.802 0.208,0.156 10 [C] 3.823,3.01 4.031,3.167 0.208,0.156 10 [D] 4.677,0.854 4.875,1.052 0.198,0.198 10 [E] 5.656,1.615 5.854,1.813 0.198,0.198 10 [F] 6.375,3.021 6.615,3.208 0.24,0.188 10 [G] 0.667,1.75 1.115,1.927 0.448,0.177 10 Idling 4.813,0.313 6.292,0.677 1.479,0.365 10 There is no designated vehicle speed 0.208,2.031 1.135,2.344 0.927,0.313 10 Ignition Switch ON 1.906,2.5 2.719,3.063 0.813,0.563 10 Warming up the engine 2.74,2.521 3.896,2.688 1.156,0.167 10 5 minutes or more 5.271,2.531 6.427,2.698 1.156,0.167 10 5 minutes or more 4.125,2.563 5.021,2.729 0.896,0.167 10 2 to 3 minutes

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on [A].

6.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher [B].

7.

Idle the engine for 5 minutes or more [C].

8.

Enter the following menus: Powertrain / Engine / Trouble Codes [D].

9.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



10.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

11.

Input the DTC: P001600 or P001800.

12.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [E] through [G].



13.

Drive the vehicle for 2 to 3 minutes [E].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


14.

Idle the engine for 5 minutes or more [F].

15.

Enter the following menus: Powertrain / Engine / Trouble Codes [G].

16.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



17.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.




CAUTION / NOTICE / HINT

HINT:
·

Bank 1 refers to the bank that includes the No. 1 cylinder*.

*: The No. 1 cylinder is the cylinder which is farthest from the transmission.

·

Bank 2 refers to the bank that does not include the No. 1 cylinder.

·

The monitor for this DTC detects when the timing chain is shifted by two teeth or more.

·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P001600 OR P001800)
a.

Turn the ignition switch to ON.


b.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
DTC P001600 or P001800 is output A
DTC P001600 or P001800 and other DTCs are output B


HINT:

If any DTCs other than P001600 or P001800 are output, troubleshoot those DTCs first.




A

2.PERFORM ACTIVE TEST USING GTS (CONTROL THE INTAKE VVT OCV DUTY RATIO)

B

2.PERFORM ACTIVE TEST USING GTS (CONTROL THE INTAKE VVT OCV DUTY RATIO)
HINT:

If the VVT system can be operated through the Active Test, it can be assumed that the VVT system is operating normally.


a.

Start the engine.


b.

Turn the A/C switch on.


c.

Perform the Active Test. Check that the displacement angle varies.

Powertrain > Engine > Active Test
Active Test Display
Control the Intake VVT OCV Duty Ratio Bank 1
Data List Display
Intake VVT Change Angle Bank 1
50004 372 4 397
Powertrain > Engine > Active Test
Active Test Display
Control the Intake VVT OCV Duty Ratio Bank 2
Data List Display
Intake VVT Change Angle Bank 2
50004 372 45 469
OK:

Displacement angle varies.



Result:
Proceed to
OK
NG



OK

3.CHECK ENGINE MECHANICAL SYSTEM

NG

4.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE (FOR INTAKE CAMSHAFT)
3.CHECK ENGINE MECHANICAL SYSTEM
a.

Check for mechanical malfunctions that affect the valve timing, such as a jumped tooth or stretching of the timing chain.


Result:
Proceed to
OK
NG



OK

7.CHECK WHETHER DTC OUTPUT RECURS (DTC P001600 OR P001800)

NG

REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA

4.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE (FOR INTAKE CAMSHAFT)
a.

Inspect the camshaft timing oil control valve (for intake camshaft).

Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>CAMSHAFT OIL CONTROL VALVE>INSPECTION


Result:
Proceed to
OK
NG



OK

5.INSPECT OIL CONTROL VALVE FILTER AND OIL PIPE

NG

REPLACE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR INTAKE CAMSHAFT)

5.INSPECT OIL CONTROL VALVE FILTER AND OIL PIPE
A225778C03
0.042,0 0.354,0.198 0.313,0.198 10 false *1 0.031,2.344 0.344,2.542 0.313,0.198 10 false *2
*1 No. 1 Oil Pipe
*2 No. 2 Oil Pipe


a.

Remove the No. 1 or No. 2 oil pipe.


b.

Remove the oil control valve filter.


c.

Check that the filter and pipe are not clogged.

OK:

The filter and pipe are not clogged.



d.

Reinstall the oil control valve filter.


e.

Reinstall the No. 1 or No. 2 oil pipe.


Result:
Proceed to
OK
NG



OK

6.INSPECT CAMSHAFT TIMING GEAR ASSEMBLY

NG

REPLACE OIL CONTROL VALVE FILTER OR OIL PIPE

6.INSPECT CAMSHAFT TIMING GEAR ASSEMBLY
a.

Inspect the camshaft timing gear assembly.

Click hereEngine / Hybrid System>1GR-FE (ENGINE MECHANICAL)>ENGINE UNIT>INSPECTION

HINT:

Perform "Inspection After Repair" after replacing the camshaft timing gear assembly.

Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

7.CHECK WHETHER DTC OUTPUT RECURS (DTC P001600 OR P001800)

NG

REPLACE CAMSHAFT TIMING GEAR ASSEMBLY

7.CHECK WHETHER DTC OUTPUT RECURS (DTC P001600 OR P001800)
a.

Turn the ignition switch to ON.


b.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

c.

Turn the ignition switch off and wait for at least 30 seconds.


d.

Turn the ignition switch to ON.


e.

Start the engine and warm it up.


f.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


g.

Read the pending DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
DTCs are not output A
DTC P001600 or P001800 is output B




A

B