Home › Engine / Hybrid System › 1GR-FE (ENGINE CONTROL) › SFI SYSTEM
RM38G0E _51 Engine / Hybrid System _100527 1GR-FE ENGINE CONTROL _0469186 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P035113  Ignition Coil "A" Circuit Open  P035213  Ignition Coil "B" Circuit Open  P035313  Ignition Coil "C" Circuit Open  P035413  Ignition Coil "D" Circuit Open  P035513  Ignition Coil "E" Circuit Open  P035613  Ignition Coil "F" Circuit Open  


DESCRIPTION

HINT:
·

These DTCs indicate malfunctions relating to the primary circuit.

·

If DTC P035113 is output, check the No. 1 ignition coil assembly (No. 1 cylinder) circuit.

·

If DTC P035213 is output, check the No. 2 ignition coil assembly (No. 2 cylinder) circuit.

·

If DTC P035313 is output, check the No. 3 ignition coil assembly (No. 3 cylinder) circuit.

·

If DTC P035413 is output, check the No. 4 ignition coil assembly (No. 4 cylinder) circuit.

·

If DTC P035513 is output, check the No. 5 ignition coil assembly (No. 5 cylinder) circuit.

·

If DTC P035613 is output, check the No. 6 ignition coil assembly (No. 6 cylinder) circuit.



A Direct Ignition System (DIS) is used on this vehicle.

The DIS is a 1-cylinder ignition system in which each cylinder is ignited by one ignition coil assembly and one spark plug is connected to the end of each secondary wiring. A powerful voltage, generated in the secondary wiring, is applied directly to each spark plug. The spark of the spark plugs passes from the center electrode to the ground electrodes.

The ECM determines the ignition timing and transmits the ignition (IGT) signals to each cylinder. Using the IGT signal, the ECM turns the power transistor inside the igniter on and off. The power transistor, in turn, switches the current supplied to the primary coil on and off. When the current to the primary coil is cut off, a powerful voltage is generated in the secondary coil. This voltage is applied to the spark plugs, causing them to spark inside the cylinders. As the ECM cuts the current to the primary coil, the igniter sends back an ignition confirmation (IGF1) signal to the ECM, for each cylinder ignition.

A319209E01
5.417,1.292 5.583,0.708 5.583,0.708 5.75,0.708 false 4.688,1.667 4.833,0.917 4.833,0.917 4.667,0.917 false 0.344,2.042 2.167,2.313 1.823,0.271 10 false Crankshaft Position Sensor 0.385,4.115 2.208,4.385 1.823,0.271 10 false VVT Sensor 0.229,5.76 2.125,6.542 1.896,0.781 10 false Other Sensors (Engine Coolant Temperature Sensor, Mass Air Flow Meter Sub-assembly, Throttle Position Sensor, etc.) 3.198,1.531 3.625,1.781 0.427,0.25 10 false IGT1 3.188,1.99 3.615,2.24 0.427,0.25 10 false IGF1 3.198,2.927 3.625,3.177 0.427,0.25 10 false IGT2 3.208,4.01 3.635,4.26 0.427,0.25 10 false IGT3 3.198,5.073 3.625,5.323 0.427,0.25 10 false IGT4 3.198,6.156 3.625,6.406 0.427,0.25 10 false IGT5 3.198,7.24 3.625,7.49 0.427,0.25 10 false IGT6 4.771,0.396 6.01,0.615 1.24,0.219 10 false from Battery 4.229,0.833 5.469,1.052 1.24,0.219 10 false Igniter 5.844,0.646 6.938,1.219 1.094,0.573 10 false No. 1 Ignition Coil Assembly 5.833,1.51 7.073,1.729 1.24,0.219 10 false No. 1 Cylinder 5.885,2.115 6.844,2.344 0.958,0.229 10 false Spark Plug 4.427,2.844 5.521,3.417 1.094,0.573 10 false No. 2 Ignition Coil Assembly 4.438,3.938 5.531,4.51 1.094,0.573 10 false No. 3 Ignition Coil Assembly 4.427,5.01 5.521,5.583 1.094,0.573 10 false No. 4 Ignition Coil Assembly 4.427,6.094 5.521,6.667 1.094,0.573 10 false No. 5 Ignition Coil Assembly 4.406,7.177 5.5,7.75 1.094,0.573 10 false No. 6 Ignition Coil Assembly 5.781,3.302 7.021,3.521 1.24,0.219 10 false No. 2 Cylinder 5.813,4.406 7.052,4.625 1.24,0.219 10 false No. 3 Cylinder 5.802,5.469 7.042,5.688 1.24,0.219 10 false No. 4 Cylinder 5.854,6.563 7.094,6.781 1.24,0.219 10 false No. 5 Cylinder 5.833,7.635 7.073,7.854 1.24,0.219 10 false No. 6 Cylinder 3.021,8.021 3.448,8.271 0.427,0.25 10 false ECM

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Note
P035113 Ignition Coil "A" Circuit Open No IGF1 signal to ECM while the engine is running (1 trip detection logic).
·

Ignition system

·

Open or short in IGF1 or IGT1 circuit between ignition coil assembly and ECM

·

No. 1 ignition coil assembly

·

IGP NO. 2 relay

·

ECM


Comes on SAE: P0351
P035213 Ignition Coil "B" Circuit Open No IGF1 signal to ECM while the engine is running (1 trip detection logic).
·

Ignition system

·

Open or short in IGF1 or IGT2 circuit between ignition coil assembly and ECM

·

No. 2 ignition coil assembly

·

IGP NO. 2 relay

·

ECM


Comes on SAE: P0352
P035313 Ignition Coil "C" Circuit Open No IGF1 signal to ECM while the engine is running (1 trip detection logic).
·

Ignition system

·

Open or short in IGF1 or IGT3 circuit between ignition coil assembly and ECM

·

No. 3 ignition coil assembly

·

IGP NO. 2 relay

·

ECM


Comes on SAE: P0353
P035413 Ignition Coil "D" Circuit Open No IGF1 signal to ECM while the engine is running (1 trip detection logic).
·

Ignition system

·

Open or short in IGF1 or IGT4 circuit between ignition coil assembly and ECM

·

No. 4 ignition coil assembly

·

IGP NO. 2 relay

·

ECM


Comes on SAE: P0354
P035513 Ignition Coil "E" Circuit Open No IGF1 signal to ECM while the engine is running (1 trip detection logic).
·

Ignition system

·

Open or short in IGF1 or IGT5 circuit between ignition coil assembly and ECM

·

No. 5 ignition coil assembly

·

IGP NO. 2 relay

·

ECM


Comes on SAE: P0355
P035613 Ignition Coil "F" Circuit Open No IGF1 signal to ECM while the engine is running (1 trip detection logic).
·

Ignition system

·

Open or short in IGF1 or IGT6 circuit between ignition coil assembly and ECM

·

No. 6 ignition coil assembly

·

IGP NO. 2 relay

·

ECM


Comes on SAE: P0356

Reference: Inspection using an oscilloscope

Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>TERMINALS OF ECM

MONITOR DESCRIPTION

A212405E36
1.781,1.646 2.177,1.823 0.396,0.177 10 false ECM 2.958,1.302 3.229,1.49 0.271,0.188 10 false IGT 2.948,1.729 3.698,2.198 0.75,0.469 10 false IGF1 4.156,1.51 4.594,1.656 0.438,0.146 10 false Igniter 5.396,1.344 6.167,1.521 0.771,0.177 10 false Ignition Coil 4.469,2.354 5.875,2.542 1.406,0.188 10 false Ignition Coil Assembly 0.208,3.115 1.146,3.448 0.938,0.333 10 false Ignition Signal (IGT) 1.646,3.542 2.135,3.729 0.49,0.188 10 false Normal 1.385,3.948 2.156,4.135 0.771,0.188 10 false Malfunction 0.188,3.896 1.156,4.417 0.969,0.521 10 false Ignition Confirmation Signal (IGF1) 3.635,4.51 4.49,4.688 0.854,0.177 10 false Circuit Open 5.948,4.969 6.313,5.167 0.365,0.198 10 false Time

If the ECM does not receive any IGF signals despite transmitting the IGT signal, it interprets this as a fault in the igniter and stores a DTC.

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on.

6.

Start the engine.

7.

Idle the engine for 10 seconds or more.

8.

Enter the following menus: Powertrain / Engine / Trouble Codes.

9.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



10.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

11.

Input the DTC: P035113, P035213, P035313, P035413, P035513 or P035613.

12.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




WIRING DIAGRAM

A488671E01
0.719,2.896 1.792,3.094 1.073,0.198 10 false Battery 1.677,2.25 3.667,2.448 1.99,0.198 10 false SUB R/B-NO. 1 1,1.073 1.615,1.271 0.615,0.198 10 false IGPD 1.583,1.198 4.51,1.458 2.927,0.26 10 false Certification ECU (Smart Key ECU Assembly) 4.625,0.896 6,1.094 1.375,0.198 10 false IGP NO. 1 4.531,0.125 4.688,0.323 0.156,0.198 10 false 3 5.281,0.115 5.438,0.313 0.156,0.198 10 false 5 4.521,0.49 4.677,0.688 0.156,0.198 10 false 1 5.281,0.5 5.438,0.698 0.156,0.198 10 false 2 5.167,3.344 7.156,3.542 1.99,0.198 10 false ECU-IGP NO. 3 4.677,2.698 4.833,2.896 0.156,0.198 10 false 3 3.906,2.698 4.063,2.896 0.156,0.198 10 false 5 4.688,3.063 4.844,3.26 0.156,0.198 10 false 1 3.885,3.073 4.042,3.271 0.156,0.198 10 false 2 3.99,3.458 5.365,3.656 1.375,0.198 10 false IGP NO. 2 1.635,3.281 1.792,3.479 0.156,0.198 10 false A 2.49,2.99 2.948,3.188 0.458,0.198 10 false IGN 1.604,1.052 2.063,1.25 0.458,0.198 10 false I40 1.219,0.844 1.531,1.042 0.313,0.198 10 false 24

A488672E01
1.49,0.302 1.646,0.5 0.156,0.198 10 false A 3.156,0.615 3.313,0.813 0.156,0.198 10 false 1 3.156,0.979 3.313,1.177 0.156,0.198 10 false 4 4.344,0.99 4.5,1.188 0.156,0.198 10 false 2 4.354,0.615 4.51,0.813 0.156,0.198 10 false 3 2.917,1.25 3.375,1.448 0.458,0.198 10 false C58 2.917,1.417 4.708,1.625 1.792,0.208 10 false No. 1 Ignition Coil Assembly 3.354,0.729 3.667,0.927 0.313,0.198 10 false +B 3.354,1.115 3.75,1.333 0.396,0.219 10 false GND 4,0.729 4.396,0.927 0.396,0.198 10 false IGT1 4.021,1.115 4.417,1.313 0.396,0.198 10 false IGF 5.938,0.604 6.552,0.802 0.615,0.198 10 false IGT1 5.948,1.042 6.563,1.24 0.615,0.198 10 false IGF1 5.948,1.854 6.563,2.052 0.615,0.198 10 false IGT2 5.948,3.115 6.563,3.313 0.615,0.198 10 false IGT3 5.948,4.375 6.563,4.573 0.615,0.198 10 false IGT4 5.958,5.625 6.573,5.823 0.615,0.198 10 false IGT5 5.938,6.875 6.552,7.073 0.615,0.198 10 false IGT6 5.719,0.646 6.031,0.844 0.313,0.198 10 false 37 5.698,1.01 6.01,1.208 0.313,0.198 10 false 54 6.292,7.75 6.75,7.948 0.458,0.198 10 false ECM 2.917,2.667 4.708,2.875 1.792,0.208 10 false No. 2 Ignition Coil Assembly 2.917,2.5 3.375,2.698 0.458,0.198 10 false C59 3.167,1.833 3.323,2.031 0.156,0.198 10 false 1 3.167,2.25 3.323,2.448 0.156,0.198 10 false 4 3.354,1.969 3.667,2.167 0.313,0.198 10 false +B 3.354,2.365 3.75,2.583 0.396,0.219 10 false GND 4,1.969 4.396,2.167 0.396,0.198 10 false IGT2 4.021,2.333 4.417,2.531 0.396,0.198 10 false IGF 4.344,1.885 4.5,2.083 0.156,0.198 10 false 3 4.344,2.25 4.5,2.448 0.156,0.198 10 false 2 5.698,1.885 6.01,2.083 0.313,0.198 10 false 36 5.688,3.146 6,3.344 0.313,0.198 10 false 35 5.698,4.385 6.01,4.583 0.313,0.198 10 false 34 5.708,5.656 6.021,5.854 0.313,0.198 10 false 33 5.698,6.917 6.01,7.115 0.313,0.198 10 false 32 2.917,3.917 4.708,4.125 1.792,0.208 10 false No. 3 Ignition Coil Assembly 2.917,5.167 4.708,5.375 1.792,0.208 10 false No. 4 Ignition Coil Assembly 2.917,6.417 4.708,6.625 1.792,0.208 10 false No. 5 Ignition Coil Assembly 2.917,7.667 4.708,7.875 1.792,0.208 10 false No. 6 Ignition Coil Assembly 2.917,3.75 3.375,3.948 0.458,0.198 10 false C60 2.917,5 3.375,5.198 0.458,0.198 10 false C61 2.917,6.25 3.375,6.448 0.458,0.198 10 false C62 2.917,7.5 3.375,7.698 0.458,0.198 10 false C63 3.354,3.25 3.667,3.448 0.313,0.198 10 false +B 3.354,4.5 3.667,4.698 0.313,0.198 10 false +B 3.354,5.75 3.667,5.948 0.313,0.198 10 false +B 3.354,7 3.667,7.198 0.313,0.198 10 false +B 3.354,3.615 3.75,3.833 0.396,0.219 10 false GND 3.354,4.865 3.75,5.083 0.396,0.219 10 false GND 3.354,6.115 3.75,6.333 0.396,0.219 10 false GND 3.354,7.365 3.75,7.583 0.396,0.219 10 false GND 4,3.25 4.396,3.448 0.396,0.198 10 false IGT3 4,4.5 4.396,4.698 0.396,0.198 10 false IGT4 4,5.75 4.396,5.948 0.396,0.198 10 false IGT5 4,6.969 4.396,7.167 0.396,0.198 10 false IGT6 4.021,3.635 4.417,3.833 0.396,0.198 10 false IGF 4.021,4.885 4.417,5.083 0.396,0.198 10 false IGF 4.021,6.135 4.417,6.333 0.396,0.198 10 false IGF 4.021,7.385 4.417,7.583 0.396,0.198 10 false IGF 3.167,3.135 3.323,3.333 0.156,0.198 10 false 1 3.167,4.385 3.323,4.583 0.156,0.198 10 false 1 3.167,5.635 3.323,5.833 0.156,0.198 10 false 1 3.167,6.917 3.323,7.115 0.156,0.198 10 false 1 3.177,3.5 3.333,3.698 0.156,0.198 10 false 4 3.167,4.75 3.323,4.948 0.156,0.198 10 false 4 3.167,6 3.323,6.198 0.156,0.198 10 false 4 3.167,7.25 3.323,7.448 0.156,0.198 10 false 4 4.344,3.135 4.5,3.333 0.156,0.198 10 false 3 4.344,4.385 4.5,4.583 0.156,0.198 10 false 3 4.344,5.635 4.5,5.833 0.156,0.198 10 false 3 4.344,6.885 4.5,7.083 0.156,0.198 10 false 3 4.344,3.5 4.5,3.698 0.156,0.198 10 false 2 4.344,4.75 4.5,4.948 0.156,0.198 10 false 2 4.344,6 4.5,6.198 0.156,0.198 10 false 2 4.344,7.25 4.5,7.448 0.156,0.198 10 false 2 6,7.75 6.458,7.948 0.458,0.198 10 false C92

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.READ OUTPUT DTCS (DTC P035113, P035213, P035313, P035413, P035513 OR P035613)
a.

Turn the ignition switch to ON.


b.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

c.

Turn the ignition switch off and wait for at least 30 seconds.


d.

Shuffle the arrangement of the ignition coil assemblies (among No. 1 to No. 6 cylinders).

NOTICE:

Do not change the location of the connectors.



e.

Perform a simulation test.


f.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
Same DTC output A
Different ignition coil DTC output B


HINT:

Perform "Inspection After Repair" after replacing the ignition coil assembly.

Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION




A

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF IGNITION COIL ASSEMBLY)

B

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF IGNITION COIL ASSEMBLY)
a.

Disconnect the ignition coil assembly connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(C58,C59,C60,C61,C62,C63)Location & Routing

Click Connector(C58)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Ignition Coil Assembly No. 1

Click Connector(C59)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Ignition Coil Assembly No. 2

Click Connector(C60)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Ignition Coil Assembly No. 3

Click Connector(C61)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Ignition Coil Assembly No. 4

Click Connector(C62)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Ignition Coil Assembly No. 5

Click Connector(C63)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Ignition Coil Assembly No. 6

C58-1 (+B) - C58-4 (GND) Ignition switch ON 11 to 14 V
C59-1 (+B) - C59-4 (GND) Ignition switch ON 11 to 14 V
C60-1 (+B) - C60-4 (GND) Ignition switch ON 11 to 14 V
C61-1 (+B) - C61-4 (GND) Ignition switch ON 11 to 14 V
C62-1 (+B) - C62-4 (GND) Ignition switch ON 11 to 14 V
C63-1 (+B) - C63-4 (GND) Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - ECM)

NG

4.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - BODY GROUND)
3.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - ECM)
a.

Disconnect the ignition coil assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(C58,C92,C59,C60,C61,C62,C63)Location & Routing

Click Connector(C58)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Ignition Coil Assembly No. 1

Click Connector(C92)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>ECM

Click Connector(C59)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Ignition Coil Assembly No. 2

Click Connector(C60)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Ignition Coil Assembly No. 3

Click Connector(C61)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Ignition Coil Assembly No. 4

Click Connector(C62)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Ignition Coil Assembly No. 5

Click Connector(C63)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Ignition Coil Assembly No. 6

C58-3 (IGT1) - C92-37 (IGT1) Always Below 1 Ω
C59-3 (IGT2) - C92-36 (IGT2) Always Below 1 Ω
C60-3 (IGT3) - C92-35 (IGT3) Always Below 1 Ω
C61-3 (IGT4) - C92-34 (IGT4) Always Below 1 Ω
C62-3 (IGT5) - C92-33 (IGT5) Always Below 1 Ω
C63-3 (IGT6) - C92-32 (IGT6) Always Below 1 Ω
C58-2 (IGF) - C92-54 (IGF1) Always Below 1 Ω
C59-2 (IGF) - C92-54 (IGF1) Always Below 1 Ω
C60-2 (IGF) - C92-54 (IGF1) Always Below 1 Ω
C61-2 (IGF) - C92-54 (IGF1) Always Below 1 Ω
C62-2 (IGF) - C92-54 (IGF1) Always Below 1 Ω
C63-2 (IGF) - C92-54 (IGF1) Always Below 1 Ω
C58-3 (IGT1) or C92-37 (IGT1) - Body ground and other terminals Always 10 kΩ or higher
C59-3 (IGT2) or C92-36 (IGT2) - Body ground and other terminals Always 10 kΩ or higher
C60-3 (IGT3) or C92-35 (IGT3) - Body ground and other terminals Always 10 kΩ or higher
C61-3 (IGT4) or C92-34 (IGT4) - Body ground and other terminals Always 10 kΩ or higher
C62-3 (IGT5) or C92-33 (IGT5) - Body ground and other terminals Always 10 kΩ or higher
C63-3 (IGT6) or C92-32 (IGT6) - Body ground and other terminals Always 10 kΩ or higher
C58-2 (IGF) or C92-54 (IGF1) - Body ground and other terminals Always 10 kΩ or higher
C59-2 (IGF) or C92-54 (IGF1) - Body ground and other terminals Always 10 kΩ or higher
C60-2 (IGF) or C92-54 (IGF1) - Body ground and other terminals Always 10 kΩ or higher
C61-2 (IGF) or C92-54 (IGF1) - Body ground and other terminals Always 10 kΩ or higher
C62-2 (IGF) or C92-54 (IGF1) - Body ground and other terminals Always 10 kΩ or higher
C63-2 (IGF) or C92-54 (IGF1) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - BODY GROUND)
a.

Disconnect the ignition coil assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(C58,C59,C60,C61,C62,C63)Location & Routing

Click Connector(C58)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Ignition Coil Assembly No. 1

Click Connector(C59)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Ignition Coil Assembly No. 2

Click Connector(C60)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Ignition Coil Assembly No. 3

Click Connector(C61)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Ignition Coil Assembly No. 4

Click Connector(C62)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Ignition Coil Assembly No. 5

Click Connector(C63)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Ignition Coil Assembly No. 6

C58-4 (GND) - Body ground Always Below 1 Ω
C59-4 (GND) - Body ground Always Below 1 Ω
C60-4 (GND) - Body ground Always Below 1 Ω
C61-4 (GND) - Body ground Always Below 1 Ω
C62-4 (GND) - Body ground Always Below 1 Ω
C63-4 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (IGP NO.2 RELAY - IGNITION COIL ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (IGP NO.2 RELAY - IGNITION COIL ASSEMBLY)
a.

Remove the IGP NO.2 relay.


b.

Disconnect the ignition coil assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(C58,C59,C60,C61,C62,C63)Location & Routing

Click Connector(C58)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Ignition Coil Assembly No. 1

Click Connector(C59)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Ignition Coil Assembly No. 2

Click Connector(C60)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Ignition Coil Assembly No. 3

Click Connector(C61)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Ignition Coil Assembly No. 4

Click Connector(C62)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Ignition Coil Assembly No. 5

Click Connector(C63)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Ignition Coil Assembly No. 6

5 (IGP NO.2 relay) - C58-1 (+B) Always Below 1 Ω
5 (IGP NO.2 relay) - C59-1 (+B) Always Below 1 Ω
5 (IGP NO.2 relay) - C60-1 (+B) Always Below 1 Ω
5 (IGP NO.2 relay) - C61-1 (+B) Always Below 1 Ω
5 (IGP NO.2 relay) - C62-1 (+B) Always Below 1 Ω
5 (IGP NO.2 relay) - C63-1 (+B) Always Below 1 Ω
5 (IGP NO.2 relay) or C58-1 (+B) - Body ground and other terminals Always 10 kΩ or higher
5 (IGP NO.2 relay) or C59-1 (+B) - Body ground and other terminals Always 10 kΩ or higher
5 (IGP NO.2 relay) or C60-1 (+B) - Body ground and other terminals Always 10 kΩ or higher
5 (IGP NO.2 relay) or C61-1 (+B)- Body ground and other terminals Always 10 kΩ or higher
5 (IGP NO.2 relay) or C62-1 (+B) - Body ground and other terminals Always 10 kΩ or higher
5 (IGP NO.2 relay) or C63-1 (+B) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.INSPECT IGP NO.2 RELAY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT IGP NO.2 RELAY

Result:
Proceed to
OK
NG



OK

7.CHECK TERMINAL VOLTAGE (POWER SOURCE OF IGP NO.2 RELAY)

NG

REPLACE IGP NO.2 RELAY

7.CHECK TERMINAL VOLTAGE (POWER SOURCE OF IGP NO.2 RELAY)
A488812C01
0.177,0.177 0.49,0.333 0.313,0.156 10 false *1 2.031,1.854 2.344,2.01 0.313,0.156 10 false *a
*1 Engine Room Relay Block No. 2
*a IGP NO.2 Relay Terminal


a.

Remove the IGP NO.2 relay.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
3 (IGP NO.2 relay) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (IGP NO.2 RELAY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (IGP NO. 2 RELAY - BATTERY)

8.CHECK HARNESS AND CONNECTOR (IGP NO.2 RELAY - BODY GROUND)
a.

Remove the IGP NO.2 relay.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (IGP NO.2 relay) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (IGP NO.2 RELAY - IGP NO.1 RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK HARNESS AND CONNECTOR (IGP NO.2 RELAY - IGP NO.1 RELAY)
a.

Remove the IGP NO.2 relay.


b.

Remove the IGP NO.1 relay.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (IGP NO.2 relay) - 5 (IGP NO.1 relay) Always Below 1 Ω
1 (IGP NO.2 relay) or 5 (IGP NO.1 relay) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR