Home › Steering › STEERING COLUMN › STEERING COLUMN ASSEMBLY (for Manual Tilt and Manual Telescopic Steering Column)
RM38G0E _55 Steering _100923 STEERING COLUMN _0469198 STEERING COLUMN ASSEMBLY(for Manual Tilt and Manual Telescopic Steering Column) A

STEERING COLUMN  STEERING COLUMN ASSEMBLY(for Manual Tilt and Manual Telescopic Steering Column)  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
C456058N01
5.438,1.906 5.854,1.906 true 6.521,0.25 6.854,0.25 true 6.021,0.115 6.563,0.427 0.542,0.313 18 false 1, 2 5.896,1.74 6.25,2.021 0.354,0.281 18 false 3

Procedure Part Name Code
Z101186

Z101188

Z101187

1 PRECAUTION - (Click here) - -
2 ALIGN FRONT WHEELS FACING STRAIGHT AHEAD - - - -
3 STEERING WHEEL ASSEMBLY 45100 - - -

C456059N01
4.271,1.25 4.083,1.25 4.083,1.25 3.844,0.917 true 5,3.865 5.448,3.865 true 4.667,2.375 5.188,2.375 true 5.552,3.719 5.948,4.083 0.396,0.365 18 false 4 4.344,1.115 4.635,1.469 0.292,0.354 18 false 5 5.531,2.24 5.927,2.604 0.396,0.365 18 false 6 5.781,3.281 6.094,3.479 0.313,0.198 10 false x 3

Procedure Part Name Code
Z101186

Z101188

Z101187

4 LOWER STEERING COLUMN COVER SUB-ASSEMBLY 45024 - - -
5 UPPER STEERING COLUMN COVER 45286B - - -
6 TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY - (Click here) - -

C456077N06
4.885,2.542 5.073,2.75 5.073,2.75 5.24,2.75 true 4.313,0.698 4.448,0.417 4.448,0.417 4.615,0.417 true 5.375,2.594 5.771,2.917 0.396,0.323 18 false 7 4.708,0.302 5.25,0.625 0.542,0.323 18 false 8 0.083,0.083 0.396,0.281 0.313,0.198 10 false *A

Procedure Part Name Code
Z101186

Z101188

Z101187

7 LOWER NO. 1 INSTRUMENT PANEL AIR BAG ASSEMBLY 73900 - - -
8 AIR DUCT SUB-ASSEMBLY - - - -

*A for LHD - -

C459448N04
4.885,2.542 5.073,2.75 5.073,2.75 5.24,2.75 true 3.115,0.813 3.25,0.531 3.25,0.531 3.417,0.531 true 5.375,2.594 5.771,2.917 0.396,0.323 18 false 7 3.5,0.396 4.042,0.719 0.542,0.323 18 false 8 0.156,0.115 0.469,0.313 0.313,0.198 10 false *A

Procedure Part Name Code
Z101186

Z101188

Z101187

7 LOWER NO. 1 INSTRUMENT PANEL AIR BAG ASSEMBLY 73900 - - -
8 AIR DUCT SUB-ASSEMBLY - - - -

*A for RHD - -

C458618N01
3.542,1.948 3.615,2.302 3.615,2.302 3.781,2.302 true 5.813,3.302 6,3.01 6,3.01 6.25,3.01 true 2.313,3.031 1.802,3.031 true 5.031,0.563 4.833,0.313 4.833,0.313 4.583,0.313 true 6.333,2.875 6.615,3.229 0.281,0.354 18 false 9 1.458,2.906 1.865,3.26 0.406,0.354 18 false 10 4.156,2.167 4.552,2.583 0.396,0.417 18 false 11 4.24,0.198 4.656,0.552 0.417,0.354 18 false 12 5.667,1.073 6.125,1.271 0.458,0.198 10 false x 2

Procedure Part Name Code
Z101186

Z101188

Z101187

9 FRONT WHEEL LH - - - -
10 NO. 2 STEERING INTERMEDIATE SHAFT SUB-ASSEMBLY 45203 (Click here) - -
11 STEERING INTERMEDIATE SHAFT ASSEMBLY 45220 (Click here) - -
12 STEERING COLUMN ASSEMBLY 45250 - - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during steering column assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Steering sensor (Including removal and installation) Steering angle neutral point Panoramic view monitor system (Click here)
Parking assist monitor system (Click here)
Steering angle setting Panoramic view monitor system (Click here)
Parking assist monitor system (Click here)
Disconnect cable from negative auxiliary battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
Multi-terrain monitor system (Click here)
Panoramic view monitor system (Click here)

HINT:

When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Stop and start system Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes). (Click here)
Lighting system (EXT) Cornering lights Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Lane tracing assist system
Lane departure alert system
Adaptive high beam system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor and expansion valve standard position is recognized. -

·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 1. PRECAUTION

Z101186

Click here(Click here)

Hide 45100 3.REMOVE STEERING WHEEL ASSEMBLY

Hide 45024 4.REMOVE LOWER STEERING COLUMN COVER SUB-ASSEMBLY

a.
C456062C01
0,0 0,0 false
V113146

Push Area
V113147

Remove in this Direction (1)
V113148

Remove in this Direction (2)
V113149

Remove in this Direction (3)



Hide 6.REMOVE TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY

Z101186

NOTICE:
·

Do not replace the spiral cable with sensor sub-assembly with the battery connected and the ignition switch to ON.

·

Do not rotate the spiral cable with sensor sub-assembly without the steering wheel assembly installed, with the battery connected and the ignition switch to ON.

·

When rotating the spiral cable with sensor sub-assembly to check the operation of the spiral cable with sensor sub-assembly (checking for abnormal noise, checking the DTC, Data List, etc.), make sure to perform the inspection with the steering wheel assembly installed.




a.
C456064C01
1.167,3.938 1.333,3.938 true 1.385,1.5 1.833,1.25 1.833,1.25 1.917,1.25 true 1,3.833 1.313,4.031 0.313,0.198 10 false *b 0.302,3.125 0.708,3.542 0.406,0.417 18 false iii 3.979,3.042 4.385,3.458 0.406,0.417 18 false iv 1.219,0.406 1.75,0.729 0.531,0.323 18 false i, ii 1.969,1.156 2.281,1.354 0.313,0.198 10 false *a
*a Slider *b Clamp
V113147

Remove in this Direction - -


i.

Disconnect each connector from the turn signal switch assembly with spiral cable sub-assembly.


ii.

Slide the slider to release the lock, and then disconnect the yellow airbag connector from the spiral cable with sensor sub-assembly.

HINT:

Refer to How to Connect or Disconnect Airbag Connector:

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>HOW TO CONNECT OR DISCONNECT AIRBAG CONNECTOR



iii.

Using pliers, support the band clamp while loosened.


iv.

Detach the claw to remove the turn signal switch assembly with spiral cable sub-assembly from the steering column assembly.



Hide 73900 7.REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY

Hide 9.REMOVE FRONT WHEEL LH

Hide 45203 10.DISCONNECT NO. 2 STEERING INTERMEDIATE SHAFT SUB-ASSEMBLY

Z101186

Click here(Click here)

Hide 45220 11.REMOVE STEERING INTERMEDIATE SHAFT ASSEMBLY

Z101186

Click here(Click here)

Hide 45250 12.REMOVE STEERING COLUMN ASSEMBLY

a.
C456065