The air conditioning amplifier assembly outputs the magnet clutch on request signal to the ECM. The ECM sends a magnet clutch on permission signal to the air conditioning amplifier assembly. The air conditioning amplifier assembly turns the magnet clutch on based on this signal.
Remove the air conditioning amplifier assembly with its connectors still connected.
Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING AMPLIFIER>REMOVAL
| *a | Component with harness connected (Air Conditioning Amplifier Assembly) |
- | - |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I32)Location & Routingewd_type=routing;type=c;code=I32 |
||
| I32-19 (MGC) - Body ground |
·
Engine running
·
Blower switch: LO
·
A/C switch: On (magnet clutch on) |
Below 1 V |
| I32-19 (MGC) - Body ground |
·
Engine running
·
Blower switch: LO
·
A/C switch : Off or on (magnet clutch off) |
11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Magnetic Clutch Fuse Shut Off Status | Magnet clutch assembly fuse shut off status | OFF/ON | OFF: Fuse has no shut off history ON: Fuse has shut off history |
- |
| Tester Display |
|---|
| Magnetic Clutch Fuse Shut Off Status |
OFF is displayed on the GTS.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Magnetic Clutch Input Signal | Magnet clutch assembly input signal | OFF/ON | OFF: Magnet clutch assembly signal not input ON: Magnet clutch assembly signal input |
- |
| Tester Display |
|---|
| Magnetic Clutch Input Signal |
ON is displayed on the GTS.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Magnetic Clutch Output Signal | Magnet clutch assembly output signal | OFF/ON | OFF: Magnet clutch assembly off ON: Magnet clutch assembly on |
- |
| Tester Display |
|---|
| Magnetic Clutch Output Signal |
ON is displayed on the GTS.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the C39 cooler compressor assembly connector.
Disconnect the B57 semiconductor power integration ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(C39,B57)Location & Routingewd_type=routing;type=c,c;code=C39,B57 |
||
| C39-1 (MG+) - B57-4 (L) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the C39 compressor with magnet clutch connector.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Magnetic Clutch Fuse Shut Off Status | Magnet clutch assembly fuse shut off status | OFF/ON | OFF: Fuse has no shut off history ON: Fuse has shut off history |
- |
| Tester Display |
|---|
| Magnetic Clutch Fuse Shut Off Status |
OFF is displayed on the GTS.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the C39 cooler compressor assembly connector.
Disconnect the B57 semiconductor power integration ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(C39,B57)Location & Routingewd_type=routing;type=c,c;code=C39,B57 |
||
| C39-1 (MG+) or B57-4 (L) - Other terminals and body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the I33 air conditioning amplifier assembly connector.
Disconnect the B57 semiconductor power integration ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I32,B57)Location & Routingewd_type=routing;type=c,c;code=I32,B57 |
||
| I32-19 (MGC) - B57-5 (MGC) | Always | Below 1 Ω |
| I32-19 (MGC) or B57-5 (MGC) - Other terminals and body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the I33 air conditioning amplifier assembly connector.
Disconnect the B2*1 or B1*2 ECM connector.
*1: for 1GR-FE
*2: for V35A-FTS
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I33,B2)Location & Routingewd_type=routing;type=c,c;code=I33,B2 |
||
| I33-19 (AC1) - B2-9 (AC1) | Always | Below 1 Ω |
| I33-3 (ACT) - B2-17 (ACT) | Always | Below 1 Ω |
| I33-19 (AC1) or B2-9 (AC1) - Other terminals and body ground | Always | 10 kΩ or higher |
| I33-3 (ACT) or B2-17 (ACT) - Other terminals and body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I33,B1)Location & Routingewd_type=routing;type=c,c;code=I33,B1 |
||
| I33-19 (AC1) - B1-61 (AC1) | Always | Below 1 Ω |
| I33-3 (ACT) - B1-52 (ACT) | Always | Below 1 Ω |
| I33-19 (AC1) or B1-61 (AC1) - Other terminals and body ground | Always | 10 kΩ or higher |
| I33-3 (ACT) or B1-52 (ACT) - Other terminals and body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the air conditioning amplifier assembly with its connectors still connected.
Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING AMPLIFIER>REMOVAL
| *a | Component with harness connected (Air Conditioning Amplifier Assembly) |
- | - |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I33)Location & Routingewd_type=routing;type=c;code=I33 |
||
| I33-19 (AC1) - Body ground |
·
Engine running
·
Blower switch: On (LO level)
·
A/C switch: On |
Below 1 V |
| I33-19 (AC1) - Body ground |
·
Engine running
·
Blower switch: On (LO level)
·
A/C switch: Off |
11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the air conditioning amplifier assembly with its connectors still connected.
Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING AMPLIFIER>REMOVAL
| *a | Component with harness connected (Air Conditioning Amplifier Assembly) |
- | - |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I33)Location & Routingewd_type=routing;type=c;code=I33 |
||
| I33-3 (ACT) - Body ground |
·
Engine running
·
Blower switch: LO
·
A/C switch: Off or on (magnet clutch off) |
Below 1 V |
| I33-3 (ACT) - Body ground |
·
Engine running
·
Blower switch: LO
·
A/C switch: On (magnet clutch on) |
4.5 to 5.5 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG