Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM
RM38G0E _54 Brake _100463 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0469467 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  C126E15  Reservoir Level Switch Circuit Short to Battery or Open  


DESCRIPTION

If the No. 1 skid control ECU (brake booster with master cylinder assembly) detects that the brake fluid level is low or there is an open in the brake fluid level warning switch signal circuit, DTC C126E15 is stored.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Note
C126E15 Reservoir Level Switch Circuit Short to Battery or Open The brake fluid level warning switch (brake booster with master cylinder assembly) circuit is open for 2 seconds or more.
·

Open in brake fluid level warning switch (brake booster with master cylinder assembly)

·

Open in wire harness

·

Uneven brake disc rotor wear

·

Brake fluid leaks

·

Low brake fluid

·

No. 1 skid control ECU (brake booster with master cylinder assembly)


Brake Booster Output ECU: No. 1 skid control ECU (brake booster with master cylinder assembly)

CAUTION / NOTICE / HINT

NOTICE:

After replacing the No. 1 skid control ECU (brake booster with master cylinder assembly), perform "Calibration".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>UTILITY


PROCEDURE

1.CHECK BRAKE FLUID LEVEL
a.

Check that the brake fluid level is sufficient.

HINT:

If the fluid level is low, check for fluid leaks, and repair as necessary.


i.

Check for brake fluid leaks (connection between the brake booster with accumulator pump assembly, brake actuator assembly, brake booster with master cylinder assembly and wheel cylinders).

HINT:

If no leaks exist, add and adjust fluid using the GTS.

Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE FLUID>ON-VEHICLE INSPECTION




b.

Check that there are no leaks from the connections between the brake booster with accumulator pump assembly, brake actuator assembly and brake booster with master cylinder assembly.

HINT:

As a visual check is very difficult, perform the check with the following procedure.


i.

Bleed the air from the brake system.

Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE FLUID>BLEEDING


ii.

Turn the ignition switch off.


iii.

Disconnect the B15 brake pedal stroke sensor assembly connector.


iv.

Depress the brake pedal several times to operate the pump motor, then wait until it stops.


v.

After the pump motor stops, wait for 30 seconds, then check the drop in the accumulator pressure sensor output value and the state of the pump motor.

Chassis > Brake Booster > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
ECB Motor Relay Motor relay operation request OFF / ON OFF: Relay off
ON: Relay on
ECB: Electronically Controlled Brake System
Accumulator Pressure Accumulator pressure output value Min.: 0.00 MPa
Max.: 24.48 MPa
15.00 to 21.00 MPa (Pressure stable and pump motor stopped) When brake fluid is stored in the accumulator: Accumulator pressure changes in accordance with volume of fluid stored in the accumulator
Chassis > Brake Booster > Data List
Tester Display
ECB Motor Relay
Accumulator Pressure
50003 466 96,212


Result:
Result Proceed to
The drop in the accumulator pressure sensor output value is less than 2.50 MPa 30 seconds after the pump motor stops, and the pump motor does not operate within 30 seconds after the pump motor stops. A
The drop in the accumulator pressure sensor output value is 2.50 MPa or more 30 seconds after the pump motor stops, or the pump motor operates within 30 seconds after the pump motor stops. B



A

2.INSPECT BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

B

CHECK AND REPAIR BRAKE FLUID LEAKS OR ADD FLUID

2.INSPECT BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY
a.
C230719C61
1.5,0.698 1.958,0.979 0.458,0.281 1.604,0.74 2.063,0.938 0.458,0.198 10 false B16 0.198,0.198 0.656,0.396 0.458,0.198 10 false *a
*a Component without harness connected
(Brake Fluid Level Warning Switch (Brake Booster with Master Cylinder Assembly))


Turn the ignition switch off.


b.

Reconnect the B15 brake pedal stroke sensor assembly connector.


c.

Remove the brake master cylinder reservoir filler cap assembly.


d.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



e.

Disconnect the B16 brake fluid level warning switch (brake booster with master cylinder assembly) connector.


f.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



g.

Measure the resistance according to the value(s) in the table below.

HINT:

A float is located inside the brake booster with master cylinder assembly. Its position changes according to the level of brake fluid.


Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B16)Location & Routing

Click Connector(B16)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Brake Level Warning Switch (Brake Master Cylinder Reservoir Assembly)

B16-1 - B16-2 Brake fluid level warning switch (brake booster with master cylinder assembly) off (float up) 1.84 to 2.16 kΩ
B16-1 - B16-2 Brake fluid level warning switch (brake booster with master cylinder assembly) on (float down) Below 1 Ω
(Brake fluid level is low)



h.

If there are no problems after completing the preceding inspection, adjust the brake fluid to the MAX level with the ignition switch turned to ON.


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - BRAKE FLUID LEVEL WARNING SWITCH)

NG

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - BRAKE FLUID LEVEL WARNING SWITCH)
a.

Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



c.

Disconnect the B19 No. 1 skid control ECU (brake booster with master cylinder assembly) connector.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B19,B16)Location & Routing

Click Connector(B19)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Brake Booster Control ECU (Brake Booster Assembly)

Click Connector(B16)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Brake Level Warning Switch (Brake Master Cylinder Reservoir Assembly)

B19-12 (LBL) - B16-1 Always Below 1 Ω
B19-12 (LBL) or B16-1 - Body ground Always 10 kΩ or higher
B16-2 - Body ground 1 minute or more after disconnecting the cable from the negative (-) battery terminal Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK BRAKE DISC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK BRAKE DISC
a.

Reconnect the B19 No. 1 skid control ECU (brake booster with master cylinder assembly) connector.


b.

Reconnect the B16 brake fluid level warning switch (brake booster with master cylinder assembly) connector.


c.

Disconnect the B15 brake pedal stroke sensor assembly connector.


d.

Perform a road test according to Freeze Frame Data or customer problem analysis. While driving, check for abnormal brake pedal vibration caused by brake discs that are worn or have excess runout.

OK:

Brake pedal does not vibrate during braking.


HINT:
·

An unevenly worn disc may vibrate the caliper pistons and cause fluctuations in brake line pressure, triggering a malfunction detection condition.

·

The brake pedal does not kick back due to caliper piston vibration during electronically controlled brake system control.

·

If the brake pedal stroke sensor assembly connector is disconnected, the fail-safe function will prohibit electronically controlled brake system control.

·

The Active Test does not prohibit electronically controlled brake system control when the vehicle is being driven, so disconnect the brake pedal stroke sensor assembly connector before continuing with inspection.

·

Uneven disc wear can be checked by measuring the disc thickness variation.

for Front Brake: Click hereBrake>BRAKE (FRONT)>FRONT BRAKE>INSPECTION

for Rear Brake: Click hereBrake>BRAKE (REAR)>REAR BRAKE>INSPECTION




Result:
Proceed to
OK
NG



OK

5.CLEAR DTC

NG

REPLACE BRAKE DISC

5.CLEAR DTC
a.

Turn the ignition switch off.


b.

Reconnect the B15 brake pedal stroke sensor assembly connector.


c.

Clear the DTCs.

Chassis > Brake Booster > Clear DTCs
50002 466

d.

Turn the ignition switch off.


Result:
Proceed to
NEXT



NEXT

6.RECONFIRM DTC
6.RECONFIRM DTC
a.

Based on the Freeze Frame Data and interview with the customer, attempt to reproduce the conditions when the malfunction occurred.


b.

Check if the same DTC is output.

Chassis > Brake Booster > Trouble Codes
50001 466

Result:
Result Proceed to
C126E15 is not output A
C126E15 is output B



A

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY