Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM
RM38G0E _54 Brake _100463 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0469467 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  C057728  Brake Pressure Sensor "D" Signal Bias Level Out of Range / Zero Adjustment Failure  


DESCRIPTION

The reaction force pressure sensor detects and outputs the brake fluid pressure of the stroke simulator, which changes in accordance with brake pedal operation, to the No. 1 skid control ECU (brake booster with master cylinder assembly).

HINT:

Brake pressure sensor "D": Reaction force pressure sensor


DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Note
C057728 Brake Pressure Sensor "D" Signal Bias Level Out of Range / Zero Adjustment Failure When the brake pedal is not depressed, the reaction force pressure sensor output value is -0.63 MPa (-6.4 kgf/cm2, -91.4 psi) or less or 1.53 MPa (15.6 kgf/cm2, 222 psi) or more for 3 seconds or more. No. 1 skid control ECU (brake booster with master cylinder assembly) Brake Booster Output ECU: No. 1 skid control ECU (brake booster with master cylinder assembly)

C057728 DTC Detection Conditions
Vehicle Condition
Pattern 1 Pattern 2
Diagnosis Condition When the brake pedal is not depressed ○ ○
Malfunction Status The reaction force pressure sensor output value is -0.63 MPa (-6.4 kgf/cm2, -91.4 psi) or less ○ -
The reaction force pressure sensor output value is 1.53 MPa (15.6 kgf/cm2, 222 psi) or more - ○
Detection Time 3 seconds or more. 3 seconds or more.
Number of Trips 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


CAUTION / NOTICE / HINT

NOTICE:

After replacing the No. 1 skid control ECU (brake booster with master cylinder assembly), perform "Calibration".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>UTILITY


PROCEDURE

1.CHECK BRAKE PEDAL
a.

Check that the brake pedal and the brake pedal stroke sensor assembly are properly installed and that the pedal can be depressed normally.


b.

Check and adjust the brake pedal height.

for LHD: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE PEDAL (for LHD)>ADJUSTMENT

for RHD: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE PEDAL (for RHD)>ADJUSTMENT



Result:
Proceed to
NEXT



NEXT

2.READ VALUE USING GTS (REACTION FORCE PRESSURE)
2.READ VALUE USING GTS (REACTION FORCE PRESSURE)
a.

Check that the reaction force pressure sensor output value is within 0.00 to 1.53 MPa when the brake pedal is not depressed.

Chassis > Brake Booster > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Reaction Force Pressure Pressure value of stroke simulator Min.: 0.00 MPa
Max.: 24.48 MPa
Brake pedal released: 0.00 to 1.53 MPa Brake pedal is being depressed: Changes in proportion to the depression force of the brake pedal
Chassis > Brake Booster > Data List
Tester Display
Reaction Force Pressure
50003 466 205
OK:

The reaction force pressure sensor output value is within 0.00 to 1.53 MPa.


HINT:

If the reaction force pressure sensor output value is within 0.00 to 1.53 MPa, the No. 1 skid control ECU (brake booster with master cylinder assembly) automatically performs zero point calibration every time the ignition switch is turned to ON.

Therefore, if the reaction force pressure sensor output value is not within 0.00 to 1.53 MPa, replace the No. 1 skid control ECU (brake booster with master cylinder assembly) with a new one.



Result:
Proceed to
OK
NG



OK

3.CLEAR DTC

NG

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

3.CLEAR DTC
a.

Clear the DTCs.

Chassis > Brake Booster > Clear DTCs
50002 466

b.

Turn the ignition switch off.


Result:
Proceed to
NEXT



NEXT

4.RECONFIRM DTC
4.RECONFIRM DTC
a.

Based on the Freeze Frame Data and interview with the customer, attempt to reproduce the conditions when the malfunction occurred.


b.

Check if the same DTC is output.

Chassis > Brake Booster > Trouble Codes
50001 466
HINT:

Even if the DTC is cleared, it will immediately be output again if the reaction force pressure sensor zero point malfunction remains.



Result:
Result Proceed to
C057728 is not output A
C057728 is output B



A

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY