Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM
RM38G0E _54 Brake _100463 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0469467 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  C05A128  Brake Pressure Sensor "E" Signal Bias Level Out of Range / Zero Adjustment Failure  


DESCRIPTION

The servo pressure sensor detects and transmits the servo pressure adjusted by the regulator to the No. 1 skid control ECU (brake booster with master cylinder assembly) in accordance with the vehicle condition.

HINT:

Brake pressure sensor "E": Servo pressure sensor


DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Note
C05A128 Brake Pressure Sensor "E" Signal Bias Level Out of Range / Zero Adjustment Failure When the brake pedal is not depressed, the servo pressure sensor output value is -0.63 MPa (-6.4 kgf/cm2, -91.4 psi) or less or 1.53 MPa (15.6 kgf/cm2, 222 psi) or more for 3 seconds or more. No. 1 skid control ECU (brake booster with master cylinder assembly) Brake Booster Output ECU: No. 1 skid control ECU (brake booster with master cylinder assembly)

C05A128 DTC Detection Conditions
Vehicle Condition
Pattern 1 Pattern 2
Diagnosis Condition When the brake pedal is not depressed ○ ○
Malfunction Status The servo pressure sensor output value is -0.63 MPa (-6.4 kgf/cm2, -91.4 psi) or less ○ -
The servo pressure sensor output value is 1.53 MPa (15.6 kgf/cm2, 222 psi) or more - ○
Detection Time 3 seconds or more. 3 seconds or more.
Number of Trips 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


CAUTION / NOTICE / HINT

NOTICE:

After replacing the No. 1 skid control ECU (brake booster with master cylinder assembly), perform "Calibration".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>UTILITY


PROCEDURE

1.CHECK BRAKE PEDAL
a.

Check that the brake pedal and the brake pedal stroke sensor assembly are properly installed and that the pedal can be depressed normally.


b.

Check and adjust the brake pedal height.

for LHD: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE PEDAL (for LHD)>ADJUSTMENT

for RHD: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE PEDAL (for RHD)>ADJUSTMENT



Result:
Proceed to
NEXT



NEXT

2.READ VALUE USING GTS (SERVO PRESSURE)
2.READ VALUE USING GTS (SERVO PRESSURE)
a.

Check that the servo pressure sensor output value is within 0.00 to 1.53 MPa when the brake pedal not depressed.

Chassis > Brake Booster > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Servo Pressure Pressure value of servo Min.: 0.00 MPa
Max.: 24.48 MPa
Brake pedal released: 0.00 to 1.53 MPa Brake pedal is being depressed: Changes in proportion to the depression force of the brake pedal
Chassis > Brake Booster > Data List
Tester Display
Servo Pressure
50003 466 210
OK:

The servo pressure sensor output value is within 0.00 to 1.53 MPa.


HINT:

If the servo pressure sensor output value is within 0.00 to 1.53 MPa, the No. 1 skid control ECU (brake booster with master cylinder assembly) automatically performs zero point calibration every time the ignition switch is turned to ON.

Therefore, if the servo pressure sensor output value is not within 0.00 to 1.53 MPa, replace the No. 1 skid control ECU (brake booster with master cylinder assembly) with a new one.



Result:
Proceed to
OK
NG



OK

3.CLEAR DTC

NG

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

3.CLEAR DTC
a.

Clear the DTCs.

Chassis > Brake Booster > Clear DTCs
50002 466

b.

Turn the ignition switch off.


Result:
Proceed to
NEXT



NEXT

4.RECONFIRM DTC
4.RECONFIRM DTC
a.

Based on the Freeze Frame Data and interview with the customer, attempt to reproduce the conditions when the malfunction occurred.


b.

Check if the same DTC is output.

Chassis > Brake Booster > Trouble Codes
50001 466
HINT:

Even if the DTC is cleared, it will immediately be output again if the servo pressure sensor zero point malfunction remains.



Result:
Result Proceed to
C05A128 is not output A
C05A128 is output B



A

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY