| *1 | O-RING | *2 | FUEL PUMP LIFTER ASSEMBLY |
| *3 | FUEL PUMP SPACER | - | - |
|
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) |
|
N*m (kgf*cm, ft.*lbf): Specified torque |
| * | For use with union nut wrench | ● | Non-reusable part |
|
Engine oil | - | - |
This procedure includes the installation of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
Perform "Inspection After Repair" after replacing the fuel (engine room side) pump assembly.
Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION
23224D 1.INSTALL FUEL PUMP SPACER GASKET
23100X 2.TEMPORARILY INSTALL FUEL (ENGINE ROOM SIDE) PUMP ASSEMBLY
|
|
| *1 | Camshaft | *2 | Fuel (Engine Room Side) Pump Assembly |
| *3 | Fuel Pump Lifter Assembly | - | - |
| *a | Correct | *b | Incorrect |
Turn the crankshaft pulley until the flat of the camshaft faces the fuel pump lifter assembly.
This prevents the camshaft nose from pushing up the fuel pump lifter assembly when installing the fuel (engine room side) pump assembly and No. 1 fuel pipe sub-assembly.
Apply 30 cc (1.83 cu.in.) of engine oil to the fuel pump lifter housing.
| *a | Apply engine oil | - | - |
| *a | Apply engine oil | *b | Protrusion |
| *c | Groove | - | - |
Apply engine oil to the inside of the fuel pump lifter housing and the outside of the fuel pump lifter assembly.
Set the fuel pump lifter assembly on the fuel pump lifter housing as shown in the illustration.
Align the protrusion of the fuel pump lifter assembly with the groove of the fuel pump lifter housing.
| *a | Apply engine oil | - | - |
Apply engine oil to a new O-ring and install it to the fuel (engine room side) pump assembly.
Do not damage the O-ring.
Set the fuel pump spacer and fuel (engine room side) pump assembly on the cylinder head cover sub-assembly RH with the 2 bolts.
Install the fuel (engine room side) pump assembly so that it can still be moved.
Connect the connector to the fuel (engine room side) pump assembly.
23801P 3.TEMPORARILY INSTALL NO. 1 FUEL PIPE SUB-ASSEMBLY
Temporarily install the No. 1 fuel pipe sub-assembly to the fuel (engine room side) pump assembly and No. 2 fuel delivery pipe sub-assembly RH with the 2 union nuts.
If the 2 union nuts do not make contact, loosen the No. 2 fuel delivery pipe sub-assembly RH installation bolt and adjust so that the 2 union bolts make contact.
Install the union nut by hand until all of the threads make contact.
23100X 4.TIGHTEN FUEL (ENGINE ROOM SIDE) PUMP ASSEMBLY
23801P 5.TIGHTEN NO. 1 FUEL PIPE SUB-ASSEMBLY
| *a | Torque Wrench Fulcrum Length | - | - |
Install the No. 1 fuel pipe sub-assembly to the cylinder head cover sub-assembly RH with the bolt.
Using a 17 mm union nut wrench, tighten the union nut on the No. 2 fuel delivery pipe sub-assembly RH side of the No. 1 fuel pipe sub-assembly.
Do not adjust the torque in the loosening direction.
Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
When using a 17 mm union nut wrench (fulcrum length of 30 mm (1.18 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)): 30 N*m (306 kgf*cm, 22 ft.*lbf)
Using a 17 mm union nut wrench, tighten the union nut on the fuel (engine room side) pump assembly side of the No. 1 fuel pipe sub-assembly.
Do not adjust the torque in the loosening direction.
Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
When using a 17 mm union nut wrench (fulcrum length of 30 mm (1.18 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)): 30 N*m (306 kgf*cm, 22 ft.*lbf)
23910A 6.INSTALL FUEL TUBE SUB-ASSEMBLY
Install the fuel tube sub-assembly to the fuel (engine room side) pump assembly and fuel inlet pipe sub-assembly.
Click hereEngine / Hybrid System>V35A-FTS (FUEL)>FUEL SYSTEM>PRECAUTION
17111 7.INSTALL INTAKE MANIFOLD
8.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
9. INITIALIZATION AFTER RECONNECTING BATTERY TERMINAL
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE
When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART
10.INSPECT FOR FUEL LEAK
11.PERFORM INITIALIZATION
Perform "Inspection After Repair" after replacing the fuel (engine room side) pump assembly.
Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION